ARM: nomadik: fix up SD/MMC DT settings
authorLinus Walleij <linus.walleij@linaro.org>
Mon, 1 Feb 2016 13:18:57 +0000 (14:18 +0100)
committerOlof Johansson <olof@lixom.net>
Thu, 4 Feb 2016 21:24:08 +0000 (13:24 -0800)
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.

Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.

The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.

Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
arch/arm/boot/dts/ste-nomadik-stn8815.dtsi

index d0c74385331803383d5296d7157516aa63c63758..27a333eb89870167b82a170d3553bd5078fafdfb 100644 (file)
                        };
                        mmcsd_default_mode: mmcsd_default {
                                mmcsd_default_cfg1 {
-                                       /* MCCLK */
-                                       pins = "GPIO8_B10";
-                                       ste,output = <0>;
-                               };
-                               mmcsd_default_cfg2 {
-                                       /* MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2 */
-                                       pins = "GPIO10_C11", "GPIO15_A12",
-                                       "GPIO16_C13", "GPIO23_D15";
-                                       ste,output = <1>;
-                               };
-                               mmcsd_default_cfg3 {
-                                       /* MCCMD, MCDAT3-0, MCMSFBCLK */
-                                       pins = "GPIO9_A10", "GPIO11_B11",
-                                       "GPIO12_A11", "GPIO13_C12",
-                                       "GPIO14_B12", "GPIO24_C15";
-                                       ste,input = <1>;
+                                       /*
+                                        * MCCLK, MCCMDDIR, MCDAT0DIR, MCDAT31DIR, MCDATDIR2
+                                        * MCCMD, MCDAT3-0, MCMSFBCLK
+                                        */
+                                       pins = "GPIO8_B10", "GPIO9_A10", "GPIO10_C11", "GPIO11_B11",
+                                              "GPIO12_A11", "GPIO13_C12", "GPIO14_B12", "GPIO15_A12",
+                                              "GPIO16_C13", "GPIO23_D15", "GPIO24_C15";
+                                       ste,output = <2>;
                                };
                        };
                };
                        clock-names = "mclk", "apb_pclk";
                        interrupt-parent = <&vica>;
                        interrupts = <22>;
-                       max-frequency = <48000000>;
+                       max-frequency = <400000>;
                        bus-width = <4>;
                        cap-mmc-highspeed;
                        cap-sd-highspeed;
+                       full-pwr-cycle;
+                       /*
+                        * The STw4811 circuit used with the Nomadik strictly
+                        * requires that all of these signal direction pins be
+                        * routed and used for its 4-bit levelshifter.
+                        */
+                       st,sig-dir-dat0;
+                       st,sig-dir-dat2;
+                       st,sig-dir-dat31;
+                       st,sig-dir-cmd;
+                       st,sig-pin-fbclk;
                        pinctrl-names = "default";
                        pinctrl-0 = <&mmcsd_default_mux>, <&mmcsd_default_mode>;
                        vmmc-supply = <&vmmc_regulator>;