[BNX2]: Add 40-bit DMA workaround for 5708.
authorMichael Chan <mchan@broadcom.com>
Thu, 3 May 2007 20:19:18 +0000 (13:19 -0700)
committerDavid S. Miller <davem@davemloft.net>
Thu, 3 May 2007 20:19:18 +0000 (13:19 -0700)
The internal PCIE-to-PCIX bridge of the 5708 has the same 40-bit DMA
limitation as some of the tg3 chips.  Set dma_mask and persistent DMA
mask to 40-bit to workaround.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bnx2.c
drivers/net/bnx2.h

index 6d05397420f307ca953a01939ed2b34b3588e659..679ee669e1e030bad78143c5e964a7b37957341e 100644 (file)
@@ -5711,6 +5711,7 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
        unsigned long mem_len;
        int rc;
        u32 reg;
+       u64 dma_mask, persist_dma_mask;
 
        SET_MODULE_OWNER(dev);
        SET_NETDEV_DEV(dev, &pdev->dev);
@@ -5749,21 +5750,6 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
                goto err_out_release;
        }
 
-       if (pci_set_dma_mask(pdev, DMA_64BIT_MASK) == 0) {
-               bp->flags |= USING_DAC_FLAG;
-               if (pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK) != 0) {
-                       dev_err(&pdev->dev,
-                               "pci_set_consistent_dma_mask failed, aborting.\n");
-                       rc = -EIO;
-                       goto err_out_release;
-               }
-       }
-       else if (pci_set_dma_mask(pdev, DMA_32BIT_MASK) != 0) {
-               dev_err(&pdev->dev, "System does not support DMA, aborting.\n");
-               rc = -EIO;
-               goto err_out_release;
-       }
-
        bp->dev = dev;
        bp->pdev = pdev;
 
@@ -5805,6 +5791,26 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
                }
        }
 
+       /* 5708 cannot support DMA addresses > 40-bit.  */
+       if (CHIP_NUM(bp) == CHIP_NUM_5708)
+               persist_dma_mask = dma_mask = DMA_40BIT_MASK;
+       else
+               persist_dma_mask = dma_mask = DMA_64BIT_MASK;
+
+       /* Configure DMA attributes. */
+       if (pci_set_dma_mask(pdev, dma_mask) == 0) {
+               dev->features |= NETIF_F_HIGHDMA;
+               rc = pci_set_consistent_dma_mask(pdev, persist_dma_mask);
+               if (rc) {
+                       dev_err(&pdev->dev,
+                               "pci_set_consistent_dma_mask failed, aborting.\n");
+                       goto err_out_unmap;
+               }
+       } else if ((rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) != 0) {
+               dev_err(&pdev->dev, "System does not support DMA, aborting.\n");
+               goto err_out_unmap;
+       }
+
        /* Get bus information. */
        reg = REG_RD(bp, BNX2_PCICFG_MISC_STATUS);
        if (reg & BNX2_PCICFG_MISC_STATUS_PCIX_DET) {
@@ -6114,8 +6120,6 @@ bnx2_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
        printk("\n");
 
        dev->features |= NETIF_F_SG;
-       if (bp->flags & USING_DAC_FLAG)
-               dev->features |= NETIF_F_HIGHDMA;
        dev->features |= NETIF_F_IP_CSUM;
 #ifdef BCM_VLAN
        dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
index 878eee58f12ab2b5b50584ab062612e4e745cb61..8e7b29a3f9303145999da578f838491799e3f57b 100644 (file)
@@ -6433,7 +6433,6 @@ struct bnx2 {
 #define PCI_32BIT_FLAG                 2
 #define ONE_TDMA_FLAG                  4       /* no longer used */
 #define NO_WOL_FLAG                    8
-#define USING_DAC_FLAG                 0x10
 #define USING_MSI_FLAG                 0x20
 #define ASF_ENABLE_FLAG                        0x40