(hw->bus.width == hw->bus_caps.width);
}
+/**
+ * fm10k_update_vlan_pf - Update status of VLAN ID in VLAN filter table
+ * @hw: pointer to hardware structure
+ * @vid: VLAN ID to add to table
+ * @vsi: Index indicating VF ID or PF ID in table
+ * @set: Indicates if this is a set or clear operation
+ *
+ * This function adds or removes the corresponding VLAN ID from the VLAN
+ * filter table for the corresponding function. In addition to the
+ * standard set/clear that supports one bit a multi-bit write is
+ * supported to set 64 bits at a time.
+ **/
+static s32 fm10k_update_vlan_pf(struct fm10k_hw *hw, u32 vid, u8 vsi, bool set)
+{
+ u32 vlan_table, reg, mask, bit, len;
+
+ /* verify the VSI index is valid */
+ if (vsi > FM10K_VLAN_TABLE_VSI_MAX)
+ return FM10K_ERR_PARAM;
+
+ /* VLAN multi-bit write:
+ * The multi-bit write has several parts to it.
+ * 3 2 1 0
+ * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
+ * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ * | RSVD0 | Length |C|RSVD0| VLAN ID |
+ * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ *
+ * VLAN ID: Vlan Starting value
+ * RSVD0: Reserved section, must be 0
+ * C: Flag field, 0 is set, 1 is clear (Used in VF VLAN message)
+ * Length: Number of times to repeat the bit being set
+ */
+ len = vid >> 16;
+ vid = (vid << 17) >> 17;
+
+ /* verify the reserved 0 fields are 0 */
+ if (len >= FM10K_VLAN_TABLE_VID_MAX ||
+ vid >= FM10K_VLAN_TABLE_VID_MAX)
+ return FM10K_ERR_PARAM;
+
+ /* Loop through the table updating all required VLANs */
+ for (reg = FM10K_VLAN_TABLE(vsi, vid / 32), bit = vid % 32;
+ len < FM10K_VLAN_TABLE_VID_MAX;
+ len -= 32 - bit, reg++, bit = 0) {
+ /* record the initial state of the register */
+ vlan_table = fm10k_read_reg(hw, reg);
+
+ /* truncate mask if we are at the start or end of the run */
+ mask = (~(u32)0 >> ((len < 31) ? 31 - len : 0)) << bit;
+
+ /* make necessary modifications to the register */
+ mask &= set ? ~vlan_table : vlan_table;
+ if (mask)
+ fm10k_write_reg(hw, reg, vlan_table ^ mask);
+ }
+
+ return 0;
+}
+
/**
* fm10k_read_mac_addr_pf - Read device MAC address
* @hw: pointer to the HW structure
return 0;
}
+/**
+ * fm10k_glort_valid_pf - Validate that the provided glort is valid
+ * @hw: pointer to the HW structure
+ * @glort: base glort to be validated
+ *
+ * This function will return an error if the provided glort is invalid
+ **/
+bool fm10k_glort_valid_pf(struct fm10k_hw *hw, u16 glort)
+{
+ glort &= hw->mac.dglort_map >> FM10K_DGLORTMAP_MASK_SHIFT;
+
+ return glort == (hw->mac.dglort_map & FM10K_DGLORTMAP_NONE);
+}
+
+/**
+ * fm10k_update_uc_addr_pf - Update device unicast addresss
+ * @hw: pointer to the HW structure
+ * @glort: base resource tag for this request
+ * @mac: MAC address to add/remove from table
+ * @vid: VLAN ID to add/remove from table
+ * @add: Indicates if this is an add or remove operation
+ * @flags: flags field to indicate add and secure
+ *
+ * This function generates a message to the Switch API requesting
+ * that the given logical port add/remove the given L2 MAC/VLAN address.
+ **/
+static s32 fm10k_update_xc_addr_pf(struct fm10k_hw *hw, u16 glort,
+ const u8 *mac, u16 vid, bool add, u8 flags)
+{
+ struct fm10k_mbx_info *mbx = &hw->mbx;
+ struct fm10k_mac_update mac_update;
+ u32 msg[5];
+
+ /* if glort is not valid return error */
+ if (!fm10k_glort_valid_pf(hw, glort))
+ return FM10K_ERR_PARAM;
+
+ /* drop upper 4 bits of VLAN ID */
+ vid = (vid << 4) >> 4;
+
+ /* record fields */
+ mac_update.mac_lower = cpu_to_le32(((u32)mac[2] << 24) |
+ ((u32)mac[3] << 16) |
+ ((u32)mac[4] << 8) |
+ ((u32)mac[5]));
+ mac_update.mac_upper = cpu_to_le16(((u32)mac[0] << 8) |
+ ((u32)mac[1]));
+ mac_update.vlan = cpu_to_le16(vid);
+ mac_update.glort = cpu_to_le16(glort);
+ mac_update.action = add ? 0 : 1;
+ mac_update.flags = flags;
+
+ /* populate mac_update fields */
+ fm10k_tlv_msg_init(msg, FM10K_PF_MSG_ID_UPDATE_MAC_FWD_RULE);
+ fm10k_tlv_attr_put_le_struct(msg, FM10K_PF_ATTR_ID_MAC_UPDATE,
+ &mac_update, sizeof(mac_update));
+
+ /* load onto outgoing mailbox */
+ return mbx->ops.enqueue_tx(hw, mbx, msg);
+}
+
+/**
+ * fm10k_update_uc_addr_pf - Update device unicast addresss
+ * @hw: pointer to the HW structure
+ * @glort: base resource tag for this request
+ * @mac: MAC address to add/remove from table
+ * @vid: VLAN ID to add/remove from table
+ * @add: Indicates if this is an add or remove operation
+ * @flags: flags field to indicate add and secure
+ *
+ * This function is used to add or remove unicast addresses for
+ * the PF.
+ **/
+static s32 fm10k_update_uc_addr_pf(struct fm10k_hw *hw, u16 glort,
+ const u8 *mac, u16 vid, bool add, u8 flags)
+{
+ /* verify MAC address is valid */
+ if (!is_valid_ether_addr(mac))
+ return FM10K_ERR_PARAM;
+
+ return fm10k_update_xc_addr_pf(hw, glort, mac, vid, add, flags);
+}
+
+/**
+ * fm10k_update_mc_addr_pf - Update device multicast addresses
+ * @hw: pointer to the HW structure
+ * @glort: base resource tag for this request
+ * @mac: MAC address to add/remove from table
+ * @vid: VLAN ID to add/remove from table
+ * @add: Indicates if this is an add or remove operation
+ *
+ * This function is used to add or remove multicast MAC addresses for
+ * the PF.
+ **/
+static s32 fm10k_update_mc_addr_pf(struct fm10k_hw *hw, u16 glort,
+ const u8 *mac, u16 vid, bool add)
+{
+ /* verify multicast address is valid */
+ if (!is_multicast_ether_addr(mac))
+ return FM10K_ERR_PARAM;
+
+ return fm10k_update_xc_addr_pf(hw, glort, mac, vid, add, 0);
+}
+
+/**
+ * fm10k_update_xcast_mode_pf - Request update of multicast mode
+ * @hw: pointer to hardware structure
+ * @glort: base resource tag for this request
+ * @mode: integer value indicating mode being requested
+ *
+ * This function will attempt to request a higher mode for the port
+ * so that it can enable either multicast, multicast promiscuous, or
+ * promiscuous mode of operation.
+ **/
+static s32 fm10k_update_xcast_mode_pf(struct fm10k_hw *hw, u16 glort, u8 mode)
+{
+ struct fm10k_mbx_info *mbx = &hw->mbx;
+ u32 msg[3], xcast_mode;
+
+ if (mode > FM10K_XCAST_MODE_NONE)
+ return FM10K_ERR_PARAM;
+ /* if glort is not valid return error */
+ if (!fm10k_glort_valid_pf(hw, glort))
+ return FM10K_ERR_PARAM;
+
+ /* write xcast mode as a single u32 value,
+ * lower 16 bits: glort
+ * upper 16 bits: mode
+ */
+ xcast_mode = ((u32)mode << 16) | glort;
+
+ /* generate message requesting to change xcast mode */
+ fm10k_tlv_msg_init(msg, FM10K_PF_MSG_ID_XCAST_MODES);
+ fm10k_tlv_attr_put_u32(msg, FM10K_PF_ATTR_ID_XCAST_MODE, xcast_mode);
+
+ /* load onto outgoing mailbox */
+ return mbx->ops.enqueue_tx(hw, mbx, msg);
+}
+
+/**
+ * fm10k_update_int_moderator_pf - Update interrupt moderator linked list
+ * @hw: pointer to hardware structure
+ *
+ * This function walks through the MSI-X vector table to determine the
+ * number of active interrupts and based on that information updates the
+ * interrupt moderator linked list.
+ **/
+static void fm10k_update_int_moderator_pf(struct fm10k_hw *hw)
+{
+ u32 i;
+
+ /* Disable interrupt moderator */
+ fm10k_write_reg(hw, FM10K_INT_CTRL, 0);
+
+ /* loop through PF from last to first looking enabled vectors */
+ for (i = FM10K_ITR_REG_COUNT_PF - 1; i; i--) {
+ if (!fm10k_read_reg(hw, FM10K_MSIX_VECTOR_MASK(i)))
+ break;
+ }
+
+ /* always reset VFITR2[0] to point to last enabled PF vector*/
+ fm10k_write_reg(hw, FM10K_ITR2(FM10K_ITR_REG_COUNT_PF), i);
+
+ /* reset ITR2[0] to point to last enabled PF vector */
+ fm10k_write_reg(hw, FM10K_ITR2(0), i);
+
+ /* Enable interrupt moderator */
+ fm10k_write_reg(hw, FM10K_INT_CTRL, FM10K_INT_CTRL_ENABLEMODERATOR);
+}
+
+/**
+ * fm10k_update_lport_state_pf - Notify the switch of a change in port state
+ * @hw: pointer to the HW structure
+ * @glort: base resource tag for this request
+ * @count: number of logical ports being updated
+ * @enable: boolean value indicating enable or disable
+ *
+ * This function is used to add/remove a logical port from the switch.
+ **/
+static s32 fm10k_update_lport_state_pf(struct fm10k_hw *hw, u16 glort,
+ u16 count, bool enable)
+{
+ struct fm10k_mbx_info *mbx = &hw->mbx;
+ u32 msg[3], lport_msg;
+
+ /* do nothing if we are being asked to create or destroy 0 ports */
+ if (!count)
+ return 0;
+
+ /* if glort is not valid return error */
+ if (!fm10k_glort_valid_pf(hw, glort))
+ return FM10K_ERR_PARAM;
+
+ /* construct the lport message from the 2 pieces of data we have */
+ lport_msg = ((u32)count << 16) | glort;
+
+ /* generate lport create/delete message */
+ fm10k_tlv_msg_init(msg, enable ? FM10K_PF_MSG_ID_LPORT_CREATE :
+ FM10K_PF_MSG_ID_LPORT_DELETE);
+ fm10k_tlv_attr_put_u32(msg, FM10K_PF_ATTR_ID_PORT, lport_msg);
+
+ /* load onto outgoing mailbox */
+ return mbx->ops.enqueue_tx(hw, mbx, msg);
+}
+
+/**
+ * fm10k_configure_dglort_map_pf - Configures GLORT entry and queues
+ * @hw: pointer to hardware structure
+ * @dglort: pointer to dglort configuration structure
+ *
+ * Reads the configuration structure contained in dglort_cfg and uses
+ * that information to then populate a DGLORTMAP/DEC entry and the queues
+ * to which it has been assigned.
+ **/
+static s32 fm10k_configure_dglort_map_pf(struct fm10k_hw *hw,
+ struct fm10k_dglort_cfg *dglort)
+{
+ u16 glort, queue_count, vsi_count, pc_count;
+ u16 vsi, queue, pc, q_idx;
+ u32 txqctl, dglortdec, dglortmap;
+
+ /* verify the dglort pointer */
+ if (!dglort)
+ return FM10K_ERR_PARAM;
+
+ /* verify the dglort values */
+ if ((dglort->idx > 7) || (dglort->rss_l > 7) || (dglort->pc_l > 3) ||
+ (dglort->vsi_l > 6) || (dglort->vsi_b > 64) ||
+ (dglort->queue_l > 8) || (dglort->queue_b >= 256))
+ return FM10K_ERR_PARAM;
+
+ /* determine count of VSIs and queues */
+ queue_count = 1 << (dglort->rss_l + dglort->pc_l);
+ vsi_count = 1 << (dglort->vsi_l + dglort->queue_l);
+ glort = dglort->glort;
+ q_idx = dglort->queue_b;
+
+ /* configure SGLORT for queues */
+ for (vsi = 0; vsi < vsi_count; vsi++, glort++) {
+ for (queue = 0; queue < queue_count; queue++, q_idx++) {
+ if (q_idx >= FM10K_MAX_QUEUES)
+ break;
+
+ fm10k_write_reg(hw, FM10K_TX_SGLORT(q_idx), glort);
+ fm10k_write_reg(hw, FM10K_RX_SGLORT(q_idx), glort);
+ }
+ }
+
+ /* determine count of PCs and queues */
+ queue_count = 1 << (dglort->queue_l + dglort->rss_l + dglort->vsi_l);
+ pc_count = 1 << dglort->pc_l;
+
+ /* configure PC for Tx queues */
+ for (pc = 0; pc < pc_count; pc++) {
+ q_idx = pc + dglort->queue_b;
+ for (queue = 0; queue < queue_count; queue++) {
+ if (q_idx >= FM10K_MAX_QUEUES)
+ break;
+
+ txqctl = fm10k_read_reg(hw, FM10K_TXQCTL(q_idx));
+ txqctl &= ~FM10K_TXQCTL_PC_MASK;
+ txqctl |= pc << FM10K_TXQCTL_PC_SHIFT;
+ fm10k_write_reg(hw, FM10K_TXQCTL(q_idx), txqctl);
+
+ q_idx += pc_count;
+ }
+ }
+
+ /* configure DGLORTDEC */
+ dglortdec = ((u32)(dglort->rss_l) << FM10K_DGLORTDEC_RSSLENGTH_SHIFT) |
+ ((u32)(dglort->queue_b) << FM10K_DGLORTDEC_QBASE_SHIFT) |
+ ((u32)(dglort->pc_l) << FM10K_DGLORTDEC_PCLENGTH_SHIFT) |
+ ((u32)(dglort->vsi_b) << FM10K_DGLORTDEC_VSIBASE_SHIFT) |
+ ((u32)(dglort->vsi_l) << FM10K_DGLORTDEC_VSILENGTH_SHIFT) |
+ ((u32)(dglort->queue_l));
+ if (dglort->inner_rss)
+ dglortdec |= FM10K_DGLORTDEC_INNERRSS_ENABLE;
+
+ /* configure DGLORTMAP */
+ dglortmap = (dglort->idx == fm10k_dglort_default) ?
+ FM10K_DGLORTMAP_ANY : FM10K_DGLORTMAP_ZERO;
+ dglortmap <<= dglort->vsi_l + dglort->queue_l + dglort->shared_l;
+ dglortmap |= dglort->glort;
+
+ /* write values to hardware */
+ fm10k_write_reg(hw, FM10K_DGLORTDEC(dglort->idx), dglortdec);
+ fm10k_write_reg(hw, FM10K_DGLORTMAP(dglort->idx), dglortmap);
+
+ return 0;
+}
+
/**
* fm10k_update_stats_hw_pf - Updates hardware related statistics of PF
* @hw: pointer to hardware structure
fm10k_update_hw_stats_pf(hw, stats);
}
+/**
+ * fm10k_set_dma_mask_pf - Configures PhyAddrSpace to limit DMA to system
+ * @hw: pointer to hardware structure
+ * @dma_mask: 64 bit DMA mask required for platform
+ *
+ * This function sets the PHYADDR.PhyAddrSpace bits for the endpoint in order
+ * to limit the access to memory beyond what is physically in the system.
+ **/
+static void fm10k_set_dma_mask_pf(struct fm10k_hw *hw, u64 dma_mask)
+{
+ /* we need to write the upper 32 bits of DMA mask to PhyAddrSpace */
+ u32 phyaddr = (u32)(dma_mask >> 32);
+
+ fm10k_write_reg(hw, FM10K_PHYADDR, phyaddr);
+}
+
/**
* fm10k_get_fault_pf - Record a fault in one of the interface units
* @hw: pointer to hardware structure
return 0;
}
+/**
+ * fm10k_request_lport_map_pf - Request LPORT map from the switch API
+ * @hw: pointer to hardware structure
+ *
+ **/
+static s32 fm10k_request_lport_map_pf(struct fm10k_hw *hw)
+{
+ struct fm10k_mbx_info *mbx = &hw->mbx;
+ u32 msg[1];
+
+ /* issue request asking for LPORT map */
+ fm10k_tlv_msg_init(msg, FM10K_PF_MSG_ID_LPORT_MAP);
+
+ /* load onto outgoing mailbox */
+ return mbx->ops.enqueue_tx(hw, mbx, msg);
+}
+
+/**
+ * fm10k_get_host_state_pf - Returns the state of the switch and mailbox
+ * @hw: pointer to hardware structure
+ * @switch_ready: pointer to boolean value that will record switch state
+ *
+ * This funciton will check the DMA_CTRL2 register and mailbox in order
+ * to determine if the switch is ready for the PF to begin requesting
+ * addresses and mapping traffic to the local interface.
+ **/
+static s32 fm10k_get_host_state_pf(struct fm10k_hw *hw, bool *switch_ready)
+{
+ s32 ret_val = 0;
+ u32 dma_ctrl2;
+
+ /* verify the switch is ready for interraction */
+ dma_ctrl2 = fm10k_read_reg(hw, FM10K_DMA_CTRL2);
+ if (!(dma_ctrl2 & FM10K_DMA_CTRL2_SWITCH_READY))
+ goto out;
+
+ /* retrieve generic host state info */
+ ret_val = fm10k_get_host_state_generic(hw, switch_ready);
+ if (ret_val)
+ goto out;
+
+ /* interface cannot receive traffic without logical ports */
+ if (hw->mac.dglort_map == FM10K_DGLORTMAP_NONE)
+ ret_val = fm10k_request_lport_map_pf(hw);
+
+out:
+ return ret_val;
+}
+
+/* This structure defines the attibutes to be parsed below */
+const struct fm10k_tlv_attr fm10k_lport_map_msg_attr[] = {
+ FM10K_TLV_ATTR_U32(FM10K_PF_ATTR_ID_LPORT_MAP),
+ FM10K_TLV_ATTR_LAST
+};
+
+/**
+ * fm10k_msg_lport_map_pf - Message handler for lport_map message from SM
+ * @hw: Pointer to hardware structure
+ * @results: pointer array containing parsed data
+ * @mbx: Pointer to mailbox information structure
+ *
+ * This handler configures the lport mapping based on the reply from the
+ * switch API.
+ **/
+s32 fm10k_msg_lport_map_pf(struct fm10k_hw *hw, u32 **results,
+ struct fm10k_mbx_info *mbx)
+{
+ u16 glort, mask;
+ u32 dglort_map;
+ s32 err;
+
+ err = fm10k_tlv_attr_get_u32(results[FM10K_PF_ATTR_ID_LPORT_MAP],
+ &dglort_map);
+ if (err)
+ return err;
+
+ /* extract values out of the header */
+ glort = FM10K_MSG_HDR_FIELD_GET(dglort_map, LPORT_MAP_GLORT);
+ mask = FM10K_MSG_HDR_FIELD_GET(dglort_map, LPORT_MAP_MASK);
+
+ /* verify mask is set and none of the masked bits in glort are set */
+ if (!mask || (glort & ~mask))
+ return FM10K_ERR_PARAM;
+
+ /* verify the mask is contiguous, and that it is 1's followed by 0's */
+ if (((~(mask - 1) & mask) + mask) & FM10K_DGLORTMAP_NONE)
+ return FM10K_ERR_PARAM;
+
+ /* record the glort, mask, and port count */
+ hw->mac.dglort_map = dglort_map;
+
+ return 0;
+}
+
+const struct fm10k_tlv_attr fm10k_update_pvid_msg_attr[] = {
+ FM10K_TLV_ATTR_U32(FM10K_PF_ATTR_ID_UPDATE_PVID),
+ FM10K_TLV_ATTR_LAST
+};
+
+/**
+ * fm10k_msg_update_pvid_pf - Message handler for port VLAN message from SM
+ * @hw: Pointer to hardware structure
+ * @results: pointer array containing parsed data
+ * @mbx: Pointer to mailbox information structure
+ *
+ * This handler configures the default VLAN for the PF
+ **/
+s32 fm10k_msg_update_pvid_pf(struct fm10k_hw *hw, u32 **results,
+ struct fm10k_mbx_info *mbx)
+{
+ u16 glort, pvid;
+ u32 pvid_update;
+ s32 err;
+
+ err = fm10k_tlv_attr_get_u32(results[FM10K_PF_ATTR_ID_UPDATE_PVID],
+ &pvid_update);
+ if (err)
+ return err;
+
+ /* extract values from the pvid update */
+ glort = FM10K_MSG_HDR_FIELD_GET(pvid_update, UPDATE_PVID_GLORT);
+ pvid = FM10K_MSG_HDR_FIELD_GET(pvid_update, UPDATE_PVID_PVID);
+
+ /* if glort is not valid return error */
+ if (!fm10k_glort_valid_pf(hw, glort))
+ return FM10K_ERR_PARAM;
+
+ /* verify VID is valid */
+ if (pvid >= FM10K_VLAN_TABLE_VID_MAX)
+ return FM10K_ERR_PARAM;
+
+ /* record the port VLAN ID value */
+ hw->mac.default_vid = pvid;
+
+ return 0;
+}
+
+/**
+ * fm10k_record_global_table_data - Move global table data to swapi table info
+ * @from: pointer to source table data structure
+ * @to: pointer to destination table info structure
+ *
+ * This function is will copy table_data to the table_info contained in
+ * the hw struct.
+ **/
+static void fm10k_record_global_table_data(struct fm10k_global_table_data *from,
+ struct fm10k_swapi_table_info *to)
+{
+ /* convert from le32 struct to CPU byte ordered values */
+ to->used = le32_to_cpu(from->used);
+ to->avail = le32_to_cpu(from->avail);
+}
+
+const struct fm10k_tlv_attr fm10k_err_msg_attr[] = {
+ FM10K_TLV_ATTR_LE_STRUCT(FM10K_PF_ATTR_ID_ERR,
+ sizeof(struct fm10k_swapi_error)),
+ FM10K_TLV_ATTR_LAST
+};
+
+/**
+ * fm10k_msg_err_pf - Message handler for error reply
+ * @hw: Pointer to hardware structure
+ * @results: pointer array containing parsed data
+ * @mbx: Pointer to mailbox information structure
+ *
+ * This handler will capture the data for any error replies to previous
+ * messages that the PF has sent.
+ **/
+s32 fm10k_msg_err_pf(struct fm10k_hw *hw, u32 **results,
+ struct fm10k_mbx_info *mbx)
+{
+ struct fm10k_swapi_error err_msg;
+ s32 err;
+
+ /* extract structure from message */
+ err = fm10k_tlv_attr_get_le_struct(results[FM10K_PF_ATTR_ID_ERR],
+ &err_msg, sizeof(err_msg));
+ if (err)
+ return err;
+
+ /* record table status */
+ fm10k_record_global_table_data(&err_msg.mac, &hw->swapi.mac);
+ fm10k_record_global_table_data(&err_msg.nexthop, &hw->swapi.nexthop);
+ fm10k_record_global_table_data(&err_msg.ffu, &hw->swapi.ffu);
+
+ /* record SW API status value */
+ hw->swapi.status = le32_to_cpu(err_msg.status);
+
+ return 0;
+}
+
+static const struct fm10k_msg_data fm10k_msg_data_pf[] = {
+ FM10K_PF_MSG_ERR_HANDLER(XCAST_MODES, fm10k_msg_err_pf),
+ FM10K_PF_MSG_ERR_HANDLER(UPDATE_MAC_FWD_RULE, fm10k_msg_err_pf),
+ FM10K_PF_MSG_LPORT_MAP_HANDLER(fm10k_msg_lport_map_pf),
+ FM10K_PF_MSG_ERR_HANDLER(LPORT_CREATE, fm10k_msg_err_pf),
+ FM10K_PF_MSG_ERR_HANDLER(LPORT_DELETE, fm10k_msg_err_pf),
+ FM10K_PF_MSG_UPDATE_PVID_HANDLER(fm10k_msg_update_pvid_pf),
+ FM10K_TLV_MSG_ERROR_HANDLER(fm10k_tlv_msg_error),
+};
+
static struct fm10k_mac_ops mac_ops_pf = {
.get_bus_info = &fm10k_get_bus_info_generic,
.reset_hw = &fm10k_reset_hw_pf,
.start_hw = &fm10k_start_hw_generic,
.stop_hw = &fm10k_stop_hw_generic,
.is_slot_appropriate = &fm10k_is_slot_appropriate_pf,
+ .update_vlan = &fm10k_update_vlan_pf,
.read_mac_addr = &fm10k_read_mac_addr_pf,
+ .update_uc_addr = &fm10k_update_uc_addr_pf,
+ .update_mc_addr = &fm10k_update_mc_addr_pf,
+ .update_xcast_mode = &fm10k_update_xcast_mode_pf,
+ .update_int_moderator = &fm10k_update_int_moderator_pf,
+ .update_lport_state = &fm10k_update_lport_state_pf,
.update_hw_stats = &fm10k_update_hw_stats_pf,
.rebind_hw_stats = &fm10k_rebind_hw_stats_pf,
+ .configure_dglort_map = &fm10k_configure_dglort_map_pf,
+ .set_dma_mask = &fm10k_set_dma_mask_pf,
.get_fault = &fm10k_get_fault_pf,
- .get_host_state = &fm10k_get_host_state_generic,
+ .get_host_state = &fm10k_get_host_state_pf,
};
+static s32 fm10k_get_invariants_pf(struct fm10k_hw *hw)
+{
+ fm10k_get_invariants_generic(hw);
+
+ return fm10k_sm_mbx_init(hw, &hw->mbx, fm10k_msg_data_pf);
+}
+
struct fm10k_info fm10k_pf_info = {
.mac = fm10k_mac_pf,
- .get_invariants = &fm10k_get_invariants_generic,
+ .get_invariants = &fm10k_get_invariants_pf,
.mac_ops = &mac_ops_pf,
};
projects / GitHub / LineageOS / G12 / android_kernel_amlogic_linux-4.9.git / commitdiff