*/
/* Commands */
-#define FTDI_SIO_RESET 0 /* Reset the port */
-#define FTDI_SIO_MODEM_CTRL 1 /* Set the modem control register */
-#define FTDI_SIO_SET_FLOW_CTRL 2 /* Set flow control register */
-#define FTDI_SIO_SET_BAUD_RATE 3 /* Set baud rate */
-#define FTDI_SIO_SET_DATA 4 /* Set the data characteristics of the port */
-#define FTDI_SIO_GET_MODEM_STATUS 5 /* Retrieve current value of modem status register */
-#define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
-#define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
+#define FTDI_SIO_RESET 0 /* Reset the port */
+#define FTDI_SIO_MODEM_CTRL 1 /* Set the modem control register */
+#define FTDI_SIO_SET_FLOW_CTRL 2 /* Set flow control register */
+#define FTDI_SIO_SET_BAUD_RATE 3 /* Set baud rate */
+#define FTDI_SIO_SET_DATA 4 /* Set the data characteristics of
+ the port */
+#define FTDI_SIO_GET_MODEM_STATUS 5 /* Retrieve current value of modem
+ status register */
+#define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
+#define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
#define FTDI_SIO_SET_LATENCY_TIMER 9 /* Set the latency timer */
#define FTDI_SIO_GET_LATENCY_TIMER 10 /* Get the latency timer */
*/
/* Port Identifier Table */
-#define PIT_DEFAULT 0 /* SIOA */
+#define PIT_DEFAULT 0 /* SIOA */
#define PIT_SIOA 1 /* SIOA */
/* The device this driver is tested with one has only one port */
#define PIT_SIOB 2 /* SIOB */
* wLength: 0
* Data: None
* The BaudDivisor values are calculated as follows:
- * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
- * I knew how to detect old chips to select proper base clock!
+ * - BaseClock is either 12000000 or 48000000 depending on the device.
+ * FIXME: I wish I knew how to detect old chips to select proper base clock!
* - BaudDivisor is a fixed point number encoded in a funny way.
* (--WRONG WAY OF THINKING--)
* BaudDivisor is a fixed point number encoded with following bit weighs:
* (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
* end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
* (--THE REALITY--)
- * The both-bits-set has quite different meaning from 0.75 - the chip designers
- * have decided it to mean 0.125 instead of 0.75.
+ * The both-bits-set has quite different meaning from 0.75 - the chip
+ * designers have decided it to mean 0.125 instead of 0.75.
* This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
* and Flow Control Consideration for USB to RS232".
* - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
- * automagically re-encode the resulting value to take fractions into consideration.
+ * automagically re-encode the resulting value to take fractions into
+ * consideration.
* As all values are integers, some bit twiddling is in order:
* BaudDivisor = (BaseClock / 16 / BaudRate) |
* (((BaseClock / 2 / BaudRate) & 4) ? 0x4000 // 0.5
* not supported by the FT8U232AM).
*/
-typedef enum {
+enum ftdi_chip_type {
SIO = 1,
FT8U232AM = 2,
FT232BM = 3,
FT232RL = 5,
FT2232H = 6,
FT4232H = 7
-} ftdi_chip_type_t;
-
-typedef enum {
- ftdi_sio_b300 = 0,
- ftdi_sio_b600 = 1,
- ftdi_sio_b1200 = 2,
- ftdi_sio_b2400 = 3,
- ftdi_sio_b4800 = 4,
- ftdi_sio_b9600 = 5,
- ftdi_sio_b19200 = 6,
- ftdi_sio_b38400 = 7,
- ftdi_sio_b57600 = 8,
- ftdi_sio_b115200 = 9
-} FTDI_SIO_baudrate_t;
+};
+
+enum ftdi_sio_baudrate {
+ ftdi_sio_b300 = 0,
+ ftdi_sio_b600 = 1,
+ ftdi_sio_b1200 = 2,
+ ftdi_sio_b2400 = 3,
+ ftdi_sio_b4800 = 4,
+ ftdi_sio_b9600 = 5,
+ ftdi_sio_b19200 = 6,
+ ftdi_sio_b38400 = 7,
+ ftdi_sio_b57600 = 8,
+ ftdi_sio_b115200 = 9
+};
/*
- * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
- * are calculated internally.
+ * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor
+ * values are calculated internally.
*/
-
-#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
-#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
-#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8)
-#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8)
-#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11)
-#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11)
-#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11)
-#define FTDI_SIO_SET_BREAK (0x1 << 14)
+#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
+#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
+#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8)
+#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8)
+#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11)
+#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11)
+#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11)
+#define FTDI_SIO_SET_BREAK (0x1 << 14)
/* FTDI_SIO_SET_DATA */
/*
*
* A value of zero in the hIndex field disables handshaking
*
- * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
- * and the lValue field contains the XON character.
+ * If Xon/Xoff handshaking is specified, the hValue field should contain the
+ * XOFF character and the lValue field contains the XON character.
*/
/*
/* FTDI_SIO_SET_ERROR_CHAR */
-/* Set the parity error replacement character for the specified communications port */
+/*
+ * Set the parity error replacement character for the specified communications
+ * port
+ */
/*
* BmRequestType: 0100 0000b
*
* IN Endpoint
*
- * The device reserves the first two bytes of data on this endpoint to contain the current
- * values of the modem and line status registers. In the absence of data, the device
- * generates a message consisting of these two status bytes every 40 ms
+ * The device reserves the first two bytes of data on this endpoint to contain
+ * the current values of the modem and line status registers. In the absence of
+ * data, the device generates a message consisting of these two status bytes
+ * every 40 ms
*
* Byte 0: Modem Status
*
#define FTDI_RS0_RI (1 << 6)
#define FTDI_RS0_RLSD (1 << 7)
-#define FTDI_RS_DR 1
-#define FTDI_RS_OE (1<<1)
-#define FTDI_RS_PE (1<<2)
-#define FTDI_RS_FE (1<<3)
-#define FTDI_RS_BI (1<<4)
-#define FTDI_RS_THRE (1<<5)
-#define FTDI_RS_TEMT (1<<6)
-#define FTDI_RS_FIFO (1<<7)
+#define FTDI_RS_DR 1
+#define FTDI_RS_OE (1<<1)
+#define FTDI_RS_PE (1<<2)
+#define FTDI_RS_FE (1<<3)
+#define FTDI_RS_BI (1<<4)
+#define FTDI_RS_THRE (1<<5)
+#define FTDI_RS_TEMT (1<<6)
+#define FTDI_RS_FIFO (1<<7)
/*
* OUT Endpoint
*
- * This device reserves the first bytes of data on this endpoint contain the length
- * and port identifier of the message. For the FTDI USB Serial converter the port
- * identifier is always 1.
+ * This device reserves the first bytes of data on this endpoint contain the
+ * length and port identifier of the message. For the FTDI USB Serial converter
+ * the port identifier is always 1.
*
* Byte 0: Line Status
*
/*
* Hameg HO820 and HO870 interface (using VID 0x0403)
*/
-#define HAMEG_HO820_PID 0xed74
-#define HAMEG_HO870_PID 0xed71
+#define HAMEG_HO820_PID 0xed74
+#define HAMEG_HO870_PID 0xed71
/*
* MaxStream devices www.maxstream.net
* and Mike Studer (K6EEP) <k6eep@hamsoftware.org>.
* Ian Abbott <abbotti@mev.co.uk> added a few more from the driver INF file.
*/
-#define FTDI_MHAM_KW_PID 0xEEE8 /* USB-KW interface */
-#define FTDI_MHAM_YS_PID 0xEEE9 /* USB-YS interface */
-#define FTDI_MHAM_Y6_PID 0xEEEA /* USB-Y6 interface */
-#define FTDI_MHAM_Y8_PID 0xEEEB /* USB-Y8 interface */
-#define FTDI_MHAM_IC_PID 0xEEEC /* USB-IC interface */
-#define FTDI_MHAM_DB9_PID 0xEEED /* USB-DB9 interface */
-#define FTDI_MHAM_RS232_PID 0xEEEE /* USB-RS232 interface */
-#define FTDI_MHAM_Y9_PID 0xEEEF /* USB-Y9 interface */
+#define FTDI_MHAM_KW_PID 0xEEE8 /* USB-KW interface */
+#define FTDI_MHAM_YS_PID 0xEEE9 /* USB-YS interface */
+#define FTDI_MHAM_Y6_PID 0xEEEA /* USB-Y6 interface */
+#define FTDI_MHAM_Y8_PID 0xEEEB /* USB-Y8 interface */
+#define FTDI_MHAM_IC_PID 0xEEEC /* USB-IC interface */
+#define FTDI_MHAM_DB9_PID 0xEEED /* USB-DB9 interface */
+#define FTDI_MHAM_RS232_PID 0xEEEE /* USB-RS232 interface */
+#define FTDI_MHAM_Y9_PID 0xEEEF /* USB-Y9 interface */
/* Domintell products http://www.domintell.com */
#define FTDI_DOMINTELL_DGQG_PID 0xEF50 /* Master */
* Blackfin gnICE JTAG
* http://docs.blackfin.uclinux.org/doku.php?id=hw:jtag:gnice
*/
-#define ADI_VID 0x0456
-#define ADI_GNICE_PID 0xF000
-#define ADI_GNICEPLUS_PID 0xF001
+#define ADI_VID 0x0456
+#define ADI_GNICE_PID 0xF000
+#define ADI_GNICEPLUS_PID 0xF001
/*
* RATOC REX-USB60F
#define SEALEVEL_2802_7_PID 0X2872 /* SeaLINK+8/485 (2802) Port 7 */
#define SEALEVEL_2802_8_PID 0X2882 /* SeaLINK+8/485 (2802) Port 8 */
#define SEALEVEL_2803_1_PID 0X2813 /* SeaLINK+8 (2803) Port 1 */
-#define SEALEVEL_2803_2_PID 0X2823 /* SeaLINK+8 (2803) Port 2 */
-#define SEALEVEL_2803_3_PID 0X2833 /* SeaLINK+8 (2803) Port 3 */
-#define SEALEVEL_2803_4_PID 0X2843 /* SeaLINK+8 (2803) Port 4 */
-#define SEALEVEL_2803_5_PID 0X2853 /* SeaLINK+8 (2803) Port 5 */
-#define SEALEVEL_2803_6_PID 0X2863 /* SeaLINK+8 (2803) Port 6 */
-#define SEALEVEL_2803_7_PID 0X2873 /* SeaLINK+8 (2803) Port 7 */
-#define SEALEVEL_2803_8_PID 0X2883 /* SeaLINK+8 (2803) Port 8 */
+#define SEALEVEL_2803_2_PID 0X2823 /* SeaLINK+8 (2803) Port 2 */
+#define SEALEVEL_2803_3_PID 0X2833 /* SeaLINK+8 (2803) Port 3 */
+#define SEALEVEL_2803_4_PID 0X2843 /* SeaLINK+8 (2803) Port 4 */
+#define SEALEVEL_2803_5_PID 0X2853 /* SeaLINK+8 (2803) Port 5 */
+#define SEALEVEL_2803_6_PID 0X2863 /* SeaLINK+8 (2803) Port 6 */
+#define SEALEVEL_2803_7_PID 0X2873 /* SeaLINK+8 (2803) Port 7 */
+#define SEALEVEL_2803_8_PID 0X2883 /* SeaLINK+8 (2803) Port 8 */
/*
* JETI SPECTROMETER SPECBOS 1201
*/
#define EVOLUTION_VID 0xDEEE /* Vendor ID */
#define EVOLUTION_ER1_PID 0x0300 /* ER1 Control Module */
-#define EVO_8U232AM_PID 0x02FF /* Evolution robotics RCM2 (FT232AM)*/
+#define EVO_8U232AM_PID 0x02FF /* Evolution robotics RCM2 (FT232AM)*/
#define EVO_HYBRID_PID 0x0302 /* Evolution robotics RCM4 PID (FT232BM)*/
#define EVO_RCM4_PID 0x0303 /* Evolution robotics RCM4 PID */
projects / GitHub / MotorolaMobilityLLC / kernel-slsi.git / commitdiff