Remove our own implementation of I2C bit-banging.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
select MII
select INET_LRO
select CRC32
+ select I2C
+ select I2C_ALGOBIT
help
This driver supports 10-gigabit Ethernet cards based on
the Solarflare Communications Solarstorm SFC4000 controller.
sfc-y += efx.o falcon.o tx.o rx.o falcon_xmac.o \
- i2c-direct.o selftest.o ethtool.o xfp_phy.o \
+ selftest.o ethtool.o xfp_phy.o \
mdio_10g.o tenxpress.o boards.o sfe4001.o
obj-$(CONFIG_SFC) += sfc.o
[EFX_BOARD_INVALID] =
{NULL, NULL, dummy_init},
[EFX_BOARD_SFE4001] =
- {"SFE4001", "10GBASE-T adapter", sfe4001_poweron},
+ {"SFE4001", "10GBASE-T adapter", sfe4001_init},
[EFX_BOARD_SFE4002] =
{"SFE4002", "XFP adapter", sfe4002_init},
};
};
extern int efx_set_board_info(struct efx_nic *efx, u16 revision_info);
-extern int sfe4001_poweron(struct efx_nic *efx);
-extern void sfe4001_poweroff(struct efx_nic *efx);
+extern int sfe4001_init(struct efx_nic *efx);
/* Are we putting the PHY into flash config mode */
extern unsigned int sfe4001_phy_flash_cfg;
.init = efx_nic_dummy_op_int,
.init_leds = efx_port_dummy_op_int,
.set_fault_led = efx_port_dummy_op_blink,
+ .fini = efx_port_dummy_op_void,
};
/**************************************************************************
efx_fini_port(efx);
/* Shutdown the board, then the NIC and board state */
+ efx->board_info.fini(efx);
falcon_fini_interrupt(efx);
efx_fini_napi(efx);
#include <linux/pci.h>
#include <linux/module.h>
#include <linux/seq_file.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
#include "net_driver.h"
#include "bitfield.h"
#include "efx.h"
* struct falcon_nic_data - Falcon NIC state
* @next_buffer_table: First available buffer table id
* @pci_dev2: The secondary PCI device if present
+ * @i2c_data: Operations and state for I2C bit-bashing algorithm
*/
struct falcon_nic_data {
unsigned next_buffer_table;
struct pci_dev *pci_dev2;
+ struct i2c_algo_bit_data i2c_data;
};
/**************************************************************************
*
**************************************************************************
*/
-static void falcon_setsdascl(struct efx_i2c_interface *i2c)
+static void falcon_setsda(void *data, int state)
{
+ struct efx_nic *efx = (struct efx_nic *)data;
efx_oword_t reg;
- falcon_read(i2c->efx, ®, GPIO_CTL_REG_KER);
- EFX_SET_OWORD_FIELD(reg, GPIO0_OEN, (i2c->scl ? 0 : 1));
- EFX_SET_OWORD_FIELD(reg, GPIO3_OEN, (i2c->sda ? 0 : 1));
- falcon_write(i2c->efx, ®, GPIO_CTL_REG_KER);
+ falcon_read(efx, ®, GPIO_CTL_REG_KER);
+ EFX_SET_OWORD_FIELD(reg, GPIO3_OEN, !state);
+ falcon_write(efx, ®, GPIO_CTL_REG_KER);
}
-static int falcon_getsda(struct efx_i2c_interface *i2c)
+static void falcon_setscl(void *data, int state)
{
+ struct efx_nic *efx = (struct efx_nic *)data;
efx_oword_t reg;
- falcon_read(i2c->efx, ®, GPIO_CTL_REG_KER);
+ falcon_read(efx, ®, GPIO_CTL_REG_KER);
+ EFX_SET_OWORD_FIELD(reg, GPIO0_OEN, !state);
+ falcon_write(efx, ®, GPIO_CTL_REG_KER);
+}
+
+static int falcon_getsda(void *data)
+{
+ struct efx_nic *efx = (struct efx_nic *)data;
+ efx_oword_t reg;
+
+ falcon_read(efx, ®, GPIO_CTL_REG_KER);
return EFX_OWORD_FIELD(reg, GPIO3_IN);
}
-static int falcon_getscl(struct efx_i2c_interface *i2c)
+static int falcon_getscl(void *data)
{
+ struct efx_nic *efx = (struct efx_nic *)data;
efx_oword_t reg;
- falcon_read(i2c->efx, ®, GPIO_CTL_REG_KER);
- return EFX_DWORD_FIELD(reg, GPIO0_IN);
+ falcon_read(efx, ®, GPIO_CTL_REG_KER);
+ return EFX_OWORD_FIELD(reg, GPIO0_IN);
}
-static struct efx_i2c_bit_operations falcon_i2c_bit_operations = {
- .setsda = falcon_setsdascl,
- .setscl = falcon_setsdascl,
+static struct i2c_algo_bit_data falcon_i2c_bit_operations = {
+ .setsda = falcon_setsda,
+ .setscl = falcon_setscl,
.getsda = falcon_getsda,
.getscl = falcon_getscl,
.udelay = 100,
- .mdelay = 10,
+ /*
+ * This is the number of system clock ticks after which
+ * i2c-algo-bit gives up waiting for SCL to become high.
+ * It must be at least 2 since the first tick can happen
+ * immediately after it starts waiting.
+ */
+ .timeout = 2,
};
/**************************************************************************
struct falcon_nic_data *nic_data;
int rc;
- /* Initialise I2C interface state */
- efx->i2c.efx = efx;
- efx->i2c.op = &falcon_i2c_bit_operations;
- efx->i2c.sda = 1;
- efx->i2c.scl = 1;
-
/* Allocate storage for hardware specific data */
nic_data = kzalloc(sizeof(*nic_data), GFP_KERNEL);
efx->nic_data = nic_data;
if (rc)
goto fail5;
+ /* Initialise I2C adapter */
+ efx->i2c_adap.owner = THIS_MODULE;
+ efx->i2c_adap.class = I2C_CLASS_HWMON;
+ nic_data->i2c_data = falcon_i2c_bit_operations;
+ nic_data->i2c_data.data = efx;
+ efx->i2c_adap.algo_data = &nic_data->i2c_data;
+ efx->i2c_adap.dev.parent = &efx->pci_dev->dev;
+ strcpy(efx->i2c_adap.name, "SFC4000 GPIO");
+ rc = i2c_bit_add_bus(&efx->i2c_adap);
+ if (rc)
+ goto fail5;
+
return 0;
fail5:
void falcon_remove_nic(struct efx_nic *efx)
{
struct falcon_nic_data *nic_data = efx->nic_data;
+ int rc;
+
+ rc = i2c_del_adapter(&efx->i2c_adap);
+ BUG_ON(rc);
falcon_free_buffer(efx, &efx->irq_status);
+++ /dev/null
-/****************************************************************************
- * Driver for Solarflare Solarstorm network controllers and boards
- * Copyright 2005 Fen Systems Ltd.
- * Copyright 2006-2008 Solarflare Communications Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation, incorporated herein by reference.
- */
-
-#include <linux/delay.h>
-#include "net_driver.h"
-#include "i2c-direct.h"
-
-/*
- * I2C data (SDA) and clock (SCL) line read/writes with appropriate
- * delays.
- */
-
-static inline void setsda(struct efx_i2c_interface *i2c, int state)
-{
- udelay(i2c->op->udelay);
- i2c->sda = state;
- i2c->op->setsda(i2c);
- udelay(i2c->op->udelay);
-}
-
-static inline void setscl(struct efx_i2c_interface *i2c, int state)
-{
- udelay(i2c->op->udelay);
- i2c->scl = state;
- i2c->op->setscl(i2c);
- udelay(i2c->op->udelay);
-}
-
-static inline int getsda(struct efx_i2c_interface *i2c)
-{
- int sda;
-
- udelay(i2c->op->udelay);
- sda = i2c->op->getsda(i2c);
- udelay(i2c->op->udelay);
- return sda;
-}
-
-static inline int getscl(struct efx_i2c_interface *i2c)
-{
- int scl;
-
- udelay(i2c->op->udelay);
- scl = i2c->op->getscl(i2c);
- udelay(i2c->op->udelay);
- return scl;
-}
-
-/*
- * I2C low-level protocol operations
- *
- */
-
-static inline void i2c_release(struct efx_i2c_interface *i2c)
-{
- EFX_WARN_ON_PARANOID(!i2c->scl);
- EFX_WARN_ON_PARANOID(!i2c->sda);
- /* Devices may time out if operations do not end */
- setscl(i2c, 1);
- setsda(i2c, 1);
- EFX_BUG_ON_PARANOID(getsda(i2c) != 1);
- EFX_BUG_ON_PARANOID(getscl(i2c) != 1);
-}
-
-static inline void i2c_start(struct efx_i2c_interface *i2c)
-{
- /* We may be restarting immediately after a {send,recv}_bit,
- * so SCL will not necessarily already be high.
- */
- EFX_WARN_ON_PARANOID(!i2c->sda);
- setscl(i2c, 1);
- setsda(i2c, 0);
- setscl(i2c, 0);
- setsda(i2c, 1);
-}
-
-static inline void i2c_send_bit(struct efx_i2c_interface *i2c, int bit)
-{
- EFX_WARN_ON_PARANOID(i2c->scl != 0);
- setsda(i2c, bit);
- setscl(i2c, 1);
- setscl(i2c, 0);
- setsda(i2c, 1);
-}
-
-static inline int i2c_recv_bit(struct efx_i2c_interface *i2c)
-{
- int bit;
-
- EFX_WARN_ON_PARANOID(i2c->scl != 0);
- EFX_WARN_ON_PARANOID(!i2c->sda);
- setscl(i2c, 1);
- bit = getsda(i2c);
- setscl(i2c, 0);
- return bit;
-}
-
-static inline void i2c_stop(struct efx_i2c_interface *i2c)
-{
- EFX_WARN_ON_PARANOID(i2c->scl != 0);
- setsda(i2c, 0);
- setscl(i2c, 1);
- setsda(i2c, 1);
-}
-
-/*
- * I2C mid-level protocol operations
- *
- */
-
-/* Sends a byte via the I2C bus and checks for an acknowledgement from
- * the slave device.
- */
-static int i2c_send_byte(struct efx_i2c_interface *i2c, u8 byte)
-{
- int i;
-
- /* Send byte */
- for (i = 0; i < 8; i++) {
- i2c_send_bit(i2c, !!(byte & 0x80));
- byte <<= 1;
- }
-
- /* Check for acknowledgement from slave */
- return (i2c_recv_bit(i2c) == 0 ? 0 : -EIO);
-}
-
-/* Receives a byte via the I2C bus and sends ACK/NACK to the slave device. */
-static u8 i2c_recv_byte(struct efx_i2c_interface *i2c, int ack)
-{
- u8 value = 0;
- int i;
-
- /* Receive byte */
- for (i = 0; i < 8; i++)
- value = (value << 1) | i2c_recv_bit(i2c);
-
- /* Send ACK/NACK */
- i2c_send_bit(i2c, (ack ? 0 : 1));
-
- return value;
-}
-
-/* Calculate command byte for a read operation */
-static inline u8 i2c_read_cmd(u8 device_id)
-{
- return ((device_id << 1) | 1);
-}
-
-/* Calculate command byte for a write operation */
-static inline u8 i2c_write_cmd(u8 device_id)
-{
- return ((device_id << 1) | 0);
-}
-
-int efx_i2c_check_presence(struct efx_i2c_interface *i2c, u8 device_id)
-{
- int rc;
-
- /* If someone is driving the bus low we just give up. */
- if (getsda(i2c) == 0 || getscl(i2c) == 0) {
- EFX_ERR(i2c->efx, "%s someone is holding the I2C bus low."
- " Giving up.\n", __func__);
- return -EFAULT;
- }
-
- /* Pretend to initiate a device write */
- i2c_start(i2c);
- rc = i2c_send_byte(i2c, i2c_write_cmd(device_id));
- if (rc)
- goto out;
-
- out:
- i2c_stop(i2c);
- i2c_release(i2c);
-
- return rc;
-}
-
-/* This performs a fast read of one or more consecutive bytes from an
- * I2C device. Not all devices support consecutive reads of more than
- * one byte; for these devices use efx_i2c_read() instead.
- */
-int efx_i2c_fast_read(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, u8 *data, unsigned int len)
-{
- int i;
- int rc;
-
- EFX_WARN_ON_PARANOID(getsda(i2c) != 1);
- EFX_WARN_ON_PARANOID(getscl(i2c) != 1);
- EFX_WARN_ON_PARANOID(data == NULL);
- EFX_WARN_ON_PARANOID(len < 1);
-
- /* Select device and starting offset */
- i2c_start(i2c);
- rc = i2c_send_byte(i2c, i2c_write_cmd(device_id));
- if (rc)
- goto out;
- rc = i2c_send_byte(i2c, offset);
- if (rc)
- goto out;
-
- /* Read data from device */
- i2c_start(i2c);
- rc = i2c_send_byte(i2c, i2c_read_cmd(device_id));
- if (rc)
- goto out;
- for (i = 0; i < (len - 1); i++)
- /* Read and acknowledge all but the last byte */
- data[i] = i2c_recv_byte(i2c, 1);
- /* Read last byte with no acknowledgement */
- data[i] = i2c_recv_byte(i2c, 0);
-
- out:
- i2c_stop(i2c);
- i2c_release(i2c);
-
- return rc;
-}
-
-/* This performs a fast write of one or more consecutive bytes to an
- * I2C device. Not all devices support consecutive writes of more
- * than one byte; for these devices use efx_i2c_write() instead.
- */
-int efx_i2c_fast_write(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset,
- const u8 *data, unsigned int len)
-{
- int i;
- int rc;
-
- EFX_WARN_ON_PARANOID(getsda(i2c) != 1);
- EFX_WARN_ON_PARANOID(getscl(i2c) != 1);
- EFX_WARN_ON_PARANOID(len < 1);
-
- /* Select device and starting offset */
- i2c_start(i2c);
- rc = i2c_send_byte(i2c, i2c_write_cmd(device_id));
- if (rc)
- goto out;
- rc = i2c_send_byte(i2c, offset);
- if (rc)
- goto out;
-
- /* Write data to device */
- for (i = 0; i < len; i++) {
- rc = i2c_send_byte(i2c, data[i]);
- if (rc)
- goto out;
- }
-
- out:
- i2c_stop(i2c);
- i2c_release(i2c);
-
- return rc;
-}
-
-/* I2C byte-by-byte read */
-int efx_i2c_read(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, u8 *data, unsigned int len)
-{
- int rc;
-
- /* i2c_fast_read with length 1 is a single byte read */
- for (; len > 0; offset++, data++, len--) {
- rc = efx_i2c_fast_read(i2c, device_id, offset, data, 1);
- if (rc)
- return rc;
- }
-
- return 0;
-}
-
-/* I2C byte-by-byte write */
-int efx_i2c_write(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, const u8 *data, unsigned int len)
-{
- int rc;
-
- /* i2c_fast_write with length 1 is a single byte write */
- for (; len > 0; offset++, data++, len--) {
- rc = efx_i2c_fast_write(i2c, device_id, offset, data, 1);
- if (rc)
- return rc;
- mdelay(i2c->op->mdelay);
- }
-
- return 0;
-}
-
-
-/* This is just a slightly neater wrapper round efx_i2c_fast_write
- * in the case where the target doesn't take an offset
- */
-int efx_i2c_send_bytes(struct efx_i2c_interface *i2c,
- u8 device_id, const u8 *data, unsigned int len)
-{
- return efx_i2c_fast_write(i2c, device_id, data[0], data + 1, len - 1);
-}
-
-/* I2C receiving of bytes - does not send an offset byte */
-int efx_i2c_recv_bytes(struct efx_i2c_interface *i2c, u8 device_id,
- u8 *bytes, unsigned int len)
-{
- int i;
- int rc;
-
- EFX_WARN_ON_PARANOID(getsda(i2c) != 1);
- EFX_WARN_ON_PARANOID(getscl(i2c) != 1);
- EFX_WARN_ON_PARANOID(len < 1);
-
- /* Select device */
- i2c_start(i2c);
-
- /* Read data from device */
- rc = i2c_send_byte(i2c, i2c_read_cmd(device_id));
- if (rc)
- goto out;
-
- for (i = 0; i < (len - 1); i++)
- /* Read and acknowledge all but the last byte */
- bytes[i] = i2c_recv_byte(i2c, 1);
- /* Read last byte with no acknowledgement */
- bytes[i] = i2c_recv_byte(i2c, 0);
-
- out:
- i2c_stop(i2c);
- i2c_release(i2c);
-
- return rc;
-}
-
-/* SMBus and some I2C devices will time out if the I2C clock is
- * held low for too long. This is most likely to happen in virtualised
- * systems (when the entire domain is descheduled) but could in
- * principle happen due to preemption on any busy system (and given the
- * potential length of an I2C operation turning preemption off is not
- * a sensible option). The following functions deal with the failure by
- * retrying up to a fixed number of times.
- */
-
-#define I2C_MAX_RETRIES (10)
-
-/* The timeout problem will result in -EIO. If the wrapped function
- * returns any other error, pass this up and do not retry. */
-#define RETRY_WRAPPER(_f) \
- int retries = I2C_MAX_RETRIES; \
- int rc; \
- while (retries) { \
- rc = _f; \
- if (rc != -EIO) \
- return rc; \
- retries--; \
- } \
- return rc; \
-
-int efx_i2c_check_presence_retry(struct efx_i2c_interface *i2c, u8 device_id)
-{
- RETRY_WRAPPER(efx_i2c_check_presence(i2c, device_id))
-}
-
-int efx_i2c_read_retry(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, u8 *data, unsigned int len)
-{
- RETRY_WRAPPER(efx_i2c_read(i2c, device_id, offset, data, len))
-}
-
-int efx_i2c_write_retry(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, const u8 *data, unsigned int len)
-{
- RETRY_WRAPPER(efx_i2c_write(i2c, device_id, offset, data, len))
-}
+++ /dev/null
-/****************************************************************************
- * Driver for Solarflare Solarstorm network controllers and boards
- * Copyright 2005 Fen Systems Ltd.
- * Copyright 2006 Solarflare Communications Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License version 2 as published
- * by the Free Software Foundation, incorporated herein by reference.
- */
-
-#ifndef EFX_I2C_DIRECT_H
-#define EFX_I2C_DIRECT_H
-
-#include "net_driver.h"
-
-/*
- * Direct control of an I2C bus
- */
-
-struct efx_i2c_interface;
-
-/**
- * struct efx_i2c_bit_operations - I2C bus direct control methods
- *
- * I2C bus direct control methods.
- *
- * @setsda: Set state of SDA line
- * @setscl: Set state of SCL line
- * @getsda: Get state of SDA line
- * @getscl: Get state of SCL line
- * @udelay: Delay between each bit operation
- * @mdelay: Delay between each byte write
- */
-struct efx_i2c_bit_operations {
- void (*setsda) (struct efx_i2c_interface *i2c);
- void (*setscl) (struct efx_i2c_interface *i2c);
- int (*getsda) (struct efx_i2c_interface *i2c);
- int (*getscl) (struct efx_i2c_interface *i2c);
- unsigned int udelay;
- unsigned int mdelay;
-};
-
-/**
- * struct efx_i2c_interface - an I2C interface
- *
- * An I2C interface.
- *
- * @efx: Attached Efx NIC
- * @op: I2C bus control methods
- * @sda: Current output state of SDA line
- * @scl: Current output state of SCL line
- */
-struct efx_i2c_interface {
- struct efx_nic *efx;
- struct efx_i2c_bit_operations *op;
- unsigned int sda:1;
- unsigned int scl:1;
-};
-
-extern int efx_i2c_check_presence(struct efx_i2c_interface *i2c, u8 device_id);
-extern int efx_i2c_fast_read(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset,
- u8 *data, unsigned int len);
-extern int efx_i2c_fast_write(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset,
- const u8 *data, unsigned int len);
-extern int efx_i2c_read(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, u8 *data, unsigned int len);
-extern int efx_i2c_write(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset,
- const u8 *data, unsigned int len);
-
-extern int efx_i2c_send_bytes(struct efx_i2c_interface *i2c, u8 device_id,
- const u8 *bytes, unsigned int len);
-
-extern int efx_i2c_recv_bytes(struct efx_i2c_interface *i2c, u8 device_id,
- u8 *bytes, unsigned int len);
-
-
-/* Versions of the API that retry on failure. */
-extern int efx_i2c_check_presence_retry(struct efx_i2c_interface *i2c,
- u8 device_id);
-
-extern int efx_i2c_read_retry(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset, u8 *data, unsigned int len);
-
-extern int efx_i2c_write_retry(struct efx_i2c_interface *i2c,
- u8 device_id, u8 offset,
- const u8 *data, unsigned int len);
-
-#endif /* EFX_I2C_DIRECT_H */
#include <linux/highmem.h>
#include <linux/workqueue.h>
#include <linux/inet_lro.h>
+#include <linux/i2c.h>
#include "enum.h"
#include "bitfield.h"
-#include "i2c-direct.h"
#define EFX_MAX_LRO_DESCRIPTORS 8
#define EFX_MAX_LRO_AGGR MAX_SKB_FRAGS
* @init_leds: Sets up board LEDs
* @set_fault_led: Turns the fault LED on or off
* @blink: Starts/stops blinking
+ * @fini: Cleanup function
* @blinker: used to blink LEDs in software
+ * @hwmon_client: I2C client for hardware monitor
+ * @ioexp_client: I2C client for power/port control
*/
struct efx_board {
int type;
int (*init_leds)(struct efx_nic *efx);
void (*set_fault_led) (struct efx_nic *efx, int state);
void (*blink) (struct efx_nic *efx, int start);
+ void (*fini) (struct efx_nic *nic);
struct efx_blinker blinker;
+ struct i2c_client *hwmon_client, *ioexp_client;
};
#define STRING_TABLE_LOOKUP(val, member) \
* @membase: Memory BAR value
* @biu_lock: BIU (bus interface unit) lock
* @interrupt_mode: Interrupt mode
- * @i2c: I2C interface
+ * @i2c_adap: I2C adapter
* @board_info: Board-level information
* @state: Device state flag. Serialised by the rtnl_lock.
* @reset_pending: Pending reset method (normally RESET_TYPE_NONE)
spinlock_t biu_lock;
enum efx_int_mode interrupt_mode;
- struct efx_i2c_interface i2c;
+ struct i2c_adapter i2c_adap;
struct efx_board board_info;
enum nic_state state;
static const u8 xgphy_max_temperature = 90;
-void sfe4001_poweroff(struct efx_nic *efx)
+static void sfe4001_poweroff(struct efx_nic *efx)
{
- struct efx_i2c_interface *i2c = &efx->i2c;
+ struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
+ struct i2c_client *hwmon_client = efx->board_info.hwmon_client;
- u8 cfg, out, in;
+ /* Turn off all power rails and disable outputs */
+ i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
+ i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
+ i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);
- EFX_INFO(efx, "%s\n", __func__);
-
- /* Turn off all power rails */
- out = 0xff;
- efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
-
- /* Disable port 1 outputs on IO expander */
- cfg = 0xff;
- efx_i2c_write(i2c, PCA9539, P1_CONFIG, &cfg, 1);
+ /* Clear any over-temperature alert */
+ i2c_smbus_read_byte_data(hwmon_client, RSL);
+}
- /* Disable port 0 outputs on IO expander */
- cfg = 0xff;
- efx_i2c_write(i2c, PCA9539, P0_CONFIG, &cfg, 1);
+static void sfe4001_fini(struct efx_nic *efx)
+{
+ EFX_INFO(efx, "%s\n", __func__);
- /* Clear any over-temperature alert */
- efx_i2c_read(i2c, MAX6647, RSL, &in, 1);
+ sfe4001_poweroff(efx);
+ i2c_unregister_device(efx->board_info.ioexp_client);
+ i2c_unregister_device(efx->board_info.hwmon_client);
}
/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected
* be turned on before the PHY can be used.
* Context: Process context, rtnl lock held
*/
-int sfe4001_poweron(struct efx_nic *efx)
+int sfe4001_init(struct efx_nic *efx)
{
- struct efx_i2c_interface *i2c = &efx->i2c;
+ struct i2c_client *hwmon_client, *ioexp_client;
unsigned int count;
int rc;
- u8 out, in, cfg;
+ u8 out;
efx_dword_t reg;
+ hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647);
+ if (!hwmon_client)
+ return -EIO;
+ efx->board_info.hwmon_client = hwmon_client;
+
+ ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539);
+ if (!ioexp_client) {
+ rc = -EIO;
+ goto fail_hwmon;
+ }
+ efx->board_info.ioexp_client = ioexp_client;
+
/* 10Xpress has fixed-function LED pins, so there is no board-specific
* blink code. */
efx->board_info.blink = tenxpress_phy_blink;
falcon_xmac_writel(efx, ®, XX_PWR_RST_REG_MAC);
udelay(10);
+ efx->board_info.fini = sfe4001_fini;
+
/* Set DSP over-temperature alert threshold */
EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature);
- rc = efx_i2c_write(i2c, MAX6647, WLHO,
- &xgphy_max_temperature, 1);
+ rc = i2c_smbus_write_byte_data(hwmon_client, WLHO,
+ xgphy_max_temperature);
if (rc)
- goto fail1;
+ goto fail_ioexp;
/* Read it back and verify */
- rc = efx_i2c_read(i2c, MAX6647, RLHN, &in, 1);
- if (rc)
- goto fail1;
- if (in != xgphy_max_temperature) {
+ rc = i2c_smbus_read_byte_data(hwmon_client, RLHN);
+ if (rc < 0)
+ goto fail_ioexp;
+ if (rc != xgphy_max_temperature) {
rc = -EFAULT;
- goto fail1;
+ goto fail_ioexp;
}
/* Clear any previous over-temperature alert */
- rc = efx_i2c_read(i2c, MAX6647, RSL, &in, 1);
- if (rc)
- goto fail1;
+ rc = i2c_smbus_read_byte_data(hwmon_client, RSL);
+ if (rc < 0)
+ goto fail_ioexp;
/* Enable port 0 and port 1 outputs on IO expander */
- cfg = 0x00;
- rc = efx_i2c_write(i2c, PCA9539, P0_CONFIG, &cfg, 1);
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
if (rc)
- goto fail1;
- cfg = 0xff & ~(1 << P1_SPARE_LBN);
- rc = efx_i2c_write(i2c, PCA9539, P1_CONFIG, &cfg, 1);
+ goto fail_ioexp;
+ rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
+ 0xff & ~(1 << P1_SPARE_LBN));
if (rc)
- goto fail2;
+ goto fail_on;
/* Turn all power off then wait 1 sec. This ensures PHY is reset */
out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
(0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
(0 << P0_EN_1V0X_LBN));
- rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
if (rc)
- goto fail3;
+ goto fail_on;
schedule_timeout_uninterruptible(HZ);
count = 0;
if (sfe4001_phy_flash_cfg)
out |= 1 << P0_EN_3V3X_LBN;
- rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
if (rc)
- goto fail3;
+ goto fail_on;
msleep(10);
/* Turn on 1V power rail */
out &= ~(1 << P0_EN_1V0X_LBN);
- rc = efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
if (rc)
- goto fail3;
+ goto fail_on;
EFX_INFO(efx, "waiting for power (attempt %d)...\n", count);
schedule_timeout_uninterruptible(HZ);
/* Check DSP is powered */
- rc = efx_i2c_read(i2c, PCA9539, P1_IN, &in, 1);
- if (rc)
- goto fail3;
- if (in & (1 << P1_AFE_PWD_LBN))
+ rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
+ if (rc < 0)
+ goto fail_on;
+ if (rc & (1 << P1_AFE_PWD_LBN))
goto done;
/* DSP doesn't look powered in flash config mode */
EFX_INFO(efx, "timed out waiting for power\n");
rc = -ETIMEDOUT;
- goto fail3;
+ goto fail_on;
done:
EFX_INFO(efx, "PHY is powered on\n");
return 0;
-fail3:
- /* Turn off all power rails */
- out = 0xff;
- efx_i2c_write(i2c, PCA9539, P0_OUT, &out, 1);
- /* Disable port 1 outputs on IO expander */
- out = 0xff;
- efx_i2c_write(i2c, PCA9539, P1_CONFIG, &out, 1);
-fail2:
- /* Disable port 0 outputs on IO expander */
- out = 0xff;
- efx_i2c_write(i2c, PCA9539, P0_CONFIG, &out, 1);
-fail1:
+fail_on:
+ sfe4001_poweroff(efx);
+fail_ioexp:
+ i2c_unregister_device(ioexp_client);
+fail_hwmon:
+ i2c_unregister_device(hwmon_client);
return rc;
}
projects / GitHub / exynos8895 / android_kernel_samsung_universal8895.git / commitdiff