net/at91_ether: use macb functions for get/set hwaddr

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/ethernet/cadence/at91_ether.c b/drivers/net/ethernet/cadence/at91_ether.c
index 6eb928ea276d9237f322396fcebf5342674478d0..2f89e645fb015e46442c765e0bf7196ecfc0f14d 100644 (file)
--- a/drivers/net/ethernet/cadence/at91_ether.c
+++ b/drivers/net/ethernet/cadence/at91_ether.c
@@ -46,109 +46,6 @@
 /* max number of receive buffers */
 #define MAX_RX_DESCR   9
 
-/* ......................... ADDRESS MANAGEMENT ........................ */
-
-/*
- * NOTE: Your bootloader must always set the MAC address correctly before
- * booting into Linux.
- *
- * - It must always set the MAC address after reset, even if it doesn't
- *   happen to access the Ethernet while it's booting.  Some versions of
- *   U-Boot on the AT91RM9200-DK do not do this.
- *
- * - Likewise it must store the addresses in the correct byte order.
- *   MicroMonitor (uMon) on the CSB337 does this incorrectly (and
- *   continues to do so, for bug-compatibility).
- */
-
-static short __init unpack_mac_address(struct net_device *dev, unsigned int hi, unsigned int lo)
-{
-       struct macb *lp = netdev_priv(dev);
-       char addr[6];
-
-       if (lp->board_data.rev_eth_addr) {
-               addr[5] = (lo & 0xff);                  /* The CSB337 bootloader stores the MAC the wrong-way around */
-               addr[4] = (lo & 0xff00) >> 8;
-               addr[3] = (lo & 0xff0000) >> 16;
-               addr[2] = (lo & 0xff000000) >> 24;
-               addr[1] = (hi & 0xff);
-               addr[0] = (hi & 0xff00) >> 8;
-       }
-       else {
-               addr[0] = (lo & 0xff);
-               addr[1] = (lo & 0xff00) >> 8;
-               addr[2] = (lo & 0xff0000) >> 16;
-               addr[3] = (lo & 0xff000000) >> 24;
-               addr[4] = (hi & 0xff);
-               addr[5] = (hi & 0xff00) >> 8;
-       }
-
-       if (is_valid_ether_addr(addr)) {
-               memcpy(dev->dev_addr, &addr, 6);
-               return 1;
-       }
-       return 0;
-}
-
-/*
- * Set the ethernet MAC address in dev->dev_addr
- */
-static void __init get_mac_address(struct net_device *dev)
-{
-       struct macb *lp = netdev_priv(dev);
-
-       /* Check Specific-Address 1 */
-       if (unpack_mac_address(dev, macb_readl(lp, SA1T), macb_readl(lp, SA1B)))
-               return;
-       /* Check Specific-Address 2 */
-       if (unpack_mac_address(dev, macb_readl(lp, SA2T), macb_readl(lp, SA2B)))
-               return;
-       /* Check Specific-Address 3 */
-       if (unpack_mac_address(dev, macb_readl(lp, SA3T), macb_readl(lp, SA3B)))
-               return;
-       /* Check Specific-Address 4 */
-       if (unpack_mac_address(dev, macb_readl(lp, SA4T), macb_readl(lp, SA4B)))
-               return;
-
-       printk(KERN_ERR "at91_ether: Your bootloader did not configure a MAC address.\n");
-}
-
-/*
- * Program the hardware MAC address from dev->dev_addr.
- */
-static void update_mac_address(struct net_device *dev)
-{
-       struct macb *lp = netdev_priv(dev);
-
-       macb_writel(lp, SA1B, (dev->dev_addr[3] << 24) | (dev->dev_addr[2] << 16)
-                                       | (dev->dev_addr[1] << 8) | (dev->dev_addr[0]));
-       macb_writel(lp, SA1T, (dev->dev_addr[5] << 8) | (dev->dev_addr[4]));
-
-       macb_writel(lp, SA2B, 0);
-       macb_writel(lp, SA2T, 0);
-}
-
-/*
- * Store the new hardware address in dev->dev_addr, and update the MAC.
- */
-static int set_mac_address(struct net_device *dev, void* addr)
-{
-       struct sockaddr *address = addr;
-
-       if (!is_valid_ether_addr(address->sa_data))
-               return -EADDRNOTAVAIL;
-
-       memcpy(dev->dev_addr, address->sa_data, dev->addr_len);
-       update_mac_address(dev);
-
-       printk("%s: Setting MAC address to %pM\n", dev->name,
-              dev->dev_addr);
-
-       return 0;
-}
-
-/* ................................ MAC ................................ */
-
 /*
  * Initialize and start the Receiver and Transmit subsystems
  */
@@ -219,8 +116,7 @@ static int at91ether_open(struct net_device *dev)
        ctl = macb_readl(lp, NCR);
        macb_writel(lp, NCR, ctl | MACB_BIT(CLRSTAT));
 
-       /* Update the MAC address (incase user has changed it) */
-       update_mac_address(dev);
+       macb_set_hwaddr(lp);
 
        ret = at91ether_start(dev);
        if (ret)
@@ -438,7 +334,7 @@ static const struct net_device_ops at91ether_netdev_ops = {
        .ndo_start_xmit         = at91ether_start_xmit,
        .ndo_get_stats          = at91ether_stats,
        .ndo_set_rx_mode        = macb_set_rx_mode,
-       .ndo_set_mac_address    = set_mac_address,
+       .ndo_set_mac_address    = eth_mac_addr,
        .ndo_do_ioctl           = macb_ioctl,
        .ndo_validate_addr      = eth_validate_addr,
        .ndo_change_mtu         = eth_change_mtu,
@@ -557,9 +453,7 @@ static int __init at91ether_probe(struct platform_device *pdev)
 
        res = at91ether_get_hwaddr_dt(lp);
        if (res < 0)
-               get_mac_address(dev);           /* Get ethernet address and store it in dev->dev_addr */
-
-       update_mac_address(dev);        /* Program ethernet address into MAC */
+               macb_get_hwaddr(lp);
 
        res = at91ether_get_phy_mode_dt(pdev);
        if (res < 0) {