ARM: dts: omap3-igep0020: Add HS USB Host support

Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index eedf0d8b42d5c7d319b470a00b2dd44e671945ed..35346f2473b6f4b020c88a587b85ad03f7beb656 100644 (file)
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -55,6 +55,47 @@
                regulator-name = "vdd33a";
                regulator-always-on;
        };
+
+       /* HS USB Port 1 Power */
+       hsusb1_power: hsusb1_power_reg {
+               compatible = "regulator-fixed";
+               regulator-name = "hsusb1_vbus";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               gpio = <&twl_gpio 18 GPIO_ACTIVE_LOW>;  /* GPIO LEDA */
+               startup-delay-us = <70000>;
+       };
+
+       /* HS USB Host PHY on PORT 1 */
+       hsusb1_phy: hsusb1_phy {
+               compatible = "usb-nop-xceiv";
+               reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
+               vcc-supply = <&hsusb1_power>;
+       };
+};
+
+&omap3_pmx_core {
+       pinctrl-names = "default";
+       pinctrl-0 = <
+               &hsusbb1_pins
+       >;
+
+       hsusbb1_pins: pinmux_hsusbb1_pins {
+               pinctrl-single,pins = <
+                       0x5aa (PIN_OUTPUT | MUX_MODE3)          /* etk_ctl.hsusb1_clk */
+                       0x5a8 (PIN_OUTPUT | MUX_MODE3)          /* etk_clk.hsusb1_stp */
+                       0x5bc (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d8.hsusb1_dir */
+                       0x5be (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d9.hsusb1_nxt */
+                       0x5ac (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d0.hsusb1_data0 */
+                       0x5ae (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d1.hsusb1_data1 */
+                       0x5b0 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d2.hsusb1_data2 */
+                       0x5b2 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d3.hsusb1_data7 */
+                       0x5b4 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d4.hsusb1_data4 */
+                       0x5b6 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d5.hsusb1_data5 */
+                       0x5b8 (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d6.hsusb1_data6 */
+                       0x5ba (PIN_INPUT_PULLDOWN | MUX_MODE3)  /* etk_d7.hsusb1_data3 */
+               >;
+       };
 };
 
 &leds_pins {
@@ -166,3 +207,11 @@
                smsc,save-mac-address;
        };
 };
+
+&usbhshost {
+       port1-mode = "ehci-phy";
+};
+
+&usbhsehci {
+       phys = <&hsusb1_phy>;
+};