ltc4215/ltc4245: Discard obsolete detect methods

There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.

So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>

diff --git a/Documentation/hwmon/ltc4215 b/Documentation/hwmon/ltc4215
index 2e6a21eb656c556ce4e4c154a6e1229c35275938..c196a18462592f842d7637e3b443c295092cb78b 100644 (file)
--- a/Documentation/hwmon/ltc4215
+++ b/Documentation/hwmon/ltc4215
@@ -22,12 +22,13 @@ Usage Notes
 -----------
 
 This driver does not probe for LTC4215 devices, due to the fact that some
-of the possible addresses are unfriendly to probing. You will need to use
-the "force" parameter to tell the driver where to find the device.
+of the possible addresses are unfriendly to probing. You will have to
+instantiate the devices explicitly.
 
 Example: the following will load the driver for an LTC4215 at address 0x44
 on I2C bus #0:
-$ modprobe ltc4215 force=0,0x44
+$ modprobe ltc4215
+$ echo ltc4215 0x44 > /sys/bus/i2c/devices/i2c-0/new_device
 
 
 Sysfs entries

diff --git a/Documentation/hwmon/ltc4245 b/Documentation/hwmon/ltc4245
index bae7a3adc5d8ff72aded4e8abbd07c30de454f59..02838a47d86210fa8bee469f595c94851594bd44 100644 (file)
--- a/Documentation/hwmon/ltc4245
+++ b/Documentation/hwmon/ltc4245
@@ -23,12 +23,13 @@ Usage Notes
 -----------
 
 This driver does not probe for LTC4245 devices, due to the fact that some
-of the possible addresses are unfriendly to probing. You will need to use
-the "force" parameter to tell the driver where to find the device.
+of the possible addresses are unfriendly to probing. You will have to
+instantiate the devices explicitly.
 
 Example: the following will load the driver for an LTC4245 at address 0x23
 on I2C bus #1:
-$ modprobe ltc4245 force=1,0x23
+$ modprobe ltc4245
+$ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device
 
 
 Sysfs entries

diff --git a/drivers/hwmon/ltc4215.c b/drivers/hwmon/ltc4215.c
index 6c9a04136e0aefb9a1b4430146b1453ed9acbe3f..00d975eb5b83dcc86ddd8d5f5b6846c9d370f6e6 100644 (file)
--- a/drivers/hwmon/ltc4215.c
+++ b/drivers/hwmon/ltc4215.c
@@ -20,11 +20,6 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 
-static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/* Insmod parameters */
-I2C_CLIENT_INSMOD_1(ltc4215);
-
 /* Here are names of the chip's registers (a.k.a. commands) */
 enum ltc4215_cmd {
        LTC4215_CONTROL                 = 0x00, /* rw */
@@ -246,9 +241,13 @@ static const struct attribute_group ltc4215_group = {
 static int ltc4215_probe(struct i2c_client *client,
                         const struct i2c_device_id *id)
 {
+       struct i2c_adapter *adapter = client->adapter;
        struct ltc4215_data *data;
        int ret;
 
+       if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+               return -ENODEV;
+
        data = kzalloc(sizeof(*data), GFP_KERNEL);
        if (!data) {
                ret = -ENOMEM;
@@ -294,56 +293,20 @@ static int ltc4215_remove(struct i2c_client *client)
        return 0;
 }
 
-static int ltc4215_detect(struct i2c_client *client,
-                         int kind,
-                         struct i2c_board_info *info)
-{
-       struct i2c_adapter *adapter = client->adapter;
-
-       if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
-               return -ENODEV;
-
-       if (kind < 0) {         /* probed detection - check the chip type */
-               s32 v;          /* 8 bits from the chip, or -ERRNO */
-
-               /*
-                * Register 0x01 bit b7 is reserved, expect 0
-                * Register 0x03 bit b6 and b7 are reserved, expect 0
-                */
-               v = i2c_smbus_read_byte_data(client, LTC4215_ALERT);
-               if (v < 0 || (v & (1 << 7)) != 0)
-                       return -ENODEV;
-
-               v = i2c_smbus_read_byte_data(client, LTC4215_FAULT);
-               if (v < 0 || (v & ((1 << 6) | (1 << 7))) != 0)
-                               return -ENODEV;
-       }
-
-       strlcpy(info->type, "ltc4215", I2C_NAME_SIZE);
-       dev_info(&adapter->dev, "ltc4215 %s at address 0x%02x\n",
-                       kind < 0 ? "probed" : "forced",
-                       client->addr);
-
-       return 0;
-}
-
 static const struct i2c_device_id ltc4215_id[] = {
-       { "ltc4215", ltc4215 },
+       { "ltc4215", 0 },
        { }
 };
 MODULE_DEVICE_TABLE(i2c, ltc4215_id);
 
 /* This is the driver that will be inserted */
 static struct i2c_driver ltc4215_driver = {
-       .class          = I2C_CLASS_HWMON,
        .driver = {
                .name   = "ltc4215",
        },
        .probe          = ltc4215_probe,
        .remove         = ltc4215_remove,
        .id_table       = ltc4215_id,
-       .detect         = ltc4215_detect,
-       .address_data   = &addr_data,
 };
 
 static int __init ltc4215_init(void)

diff --git a/drivers/hwmon/ltc4245.c b/drivers/hwmon/ltc4245.c
index e389643336126897d9abd8adf08cfe3464425712..65c232a9d0c5a917b533e2aeac34c2c13aa4fba5 100644 (file)
--- a/drivers/hwmon/ltc4245.c
+++ b/drivers/hwmon/ltc4245.c
@@ -22,15 +22,6 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 
-/* Valid addresses are 0x20 - 0x3f
- *
- * For now, we do not probe, since some of these addresses
- * are known to be unfriendly to probing */
-static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
-
-/* Insmod parameters */
-I2C_CLIENT_INSMOD_1(ltc4245);
-
 /* Here are names of the chip's registers (a.k.a. commands) */
 enum ltc4245_cmd {
        LTC4245_STATUS                  = 0x00, /* readonly */
@@ -369,9 +360,13 @@ static const struct attribute_group ltc4245_group = {
 static int ltc4245_probe(struct i2c_client *client,
                         const struct i2c_device_id *id)
 {
+       struct i2c_adapter *adapter = client->adapter;
        struct ltc4245_data *data;
        int ret;
 
+       if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+               return -ENODEV;
+
        data = kzalloc(sizeof(*data), GFP_KERNEL);
        if (!data) {
                ret = -ENOMEM;
@@ -418,136 +413,20 @@ static int ltc4245_remove(struct i2c_client *client)
        return 0;
 }
 
-/* Check that some bits in a control register appear at all possible
- * locations without changing value
- *
- * @client: the i2c client to use
- * @reg: the register to read
- * @bits: the bits to check (0xff checks all bits,
- *                           0x03 checks only the last two bits)
- *
- * return -ERRNO if the register read failed
- * return -ENODEV if the register value doesn't stay constant at all
- * possible addresses
- *
- * return 0 for success
- */
-static int ltc4245_check_control_reg(struct i2c_client *client, u8 reg, u8 bits)
-{
-       int i;
-       s32 v, voff1, voff2;
-
-       /* Read register and check for error */
-       v = i2c_smbus_read_byte_data(client, reg);
-       if (v < 0)
-               return v;
-
-       v &= bits;
-
-       for (i = 0x00; i < 0xff; i += 0x20) {
-
-               voff1 = i2c_smbus_read_byte_data(client, reg + i);
-               if (voff1 < 0)
-                       return voff1;
-
-               voff2 = i2c_smbus_read_byte_data(client, reg + i + 0x08);
-               if (voff2 < 0)
-                       return voff2;
-
-               voff1 &= bits;
-               voff2 &= bits;
-
-               if (v != voff1 || v != voff2)
-                       return -ENODEV;
-       }
-
-       return 0;
-}
-
-static int ltc4245_detect(struct i2c_client *client,
-                         int kind,
-                         struct i2c_board_info *info)
-{
-       struct i2c_adapter *adapter = client->adapter;
-
-       if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
-               return -ENODEV;
-
-       if (kind < 0) {         /* probed detection - check the chip type */
-               s32 v;          /* 8 bits from the chip, or -ERRNO */
-
-               /* Chip registers 0x00-0x07 are control registers
-                * Chip registers 0x10-0x1f are data registers
-                *
-                * Address bits b7-b5 are ignored. This makes the chip "repeat"
-                * in steps of 0x20. Any control registers should appear with
-                * the same values across all duplicated addresses.
-                *
-                * Register 0x02 bit b2 is reserved, expect 0
-                * Register 0x07 bits b7 to b4 are reserved, expect 0
-                *
-                * Registers 0x01, 0x02 are control registers and should not
-                * change on their own.
-                *
-                * Register 0x06 bits b6 and b7 are control bits, and should
-                * not change on their own.
-                *
-                * Register 0x07 bits b3 to b0 are control bits, and should
-                * not change on their own.
-                */
-
-               /* read register 0x02 reserved bit, expect 0 */
-               v = i2c_smbus_read_byte_data(client, LTC4245_CONTROL);
-               if (v < 0 || (v & 0x04) != 0)
-                       return -ENODEV;
-
-               /* read register 0x07 reserved bits, expect 0 */
-               v = i2c_smbus_read_byte_data(client, LTC4245_ADCADR);
-               if (v < 0 || (v & 0xf0) != 0)
-                       return -ENODEV;
-
-               /* check that the alert register appears at all locations */
-               if (ltc4245_check_control_reg(client, LTC4245_ALERT, 0xff))
-                       return -ENODEV;
-
-               /* check that the control register appears at all locations */
-               if (ltc4245_check_control_reg(client, LTC4245_CONTROL, 0xff))
-                       return -ENODEV;
-
-               /* check that register 0x06 bits b6 and b7 stay constant */
-               if (ltc4245_check_control_reg(client, LTC4245_GPIO, 0xc0))
-                       return -ENODEV;
-
-               /* check that register 0x07 bits b3-b0 stay constant */
-               if (ltc4245_check_control_reg(client, LTC4245_ADCADR, 0x0f))
-                       return -ENODEV;
-       }
-
-       strlcpy(info->type, "ltc4245", I2C_NAME_SIZE);
-       dev_info(&adapter->dev, "ltc4245 %s at address 0x%02x\n",
-                       kind < 0 ? "probed" : "forced",
-                       client->addr);
-
-       return 0;
-}
-
 static const struct i2c_device_id ltc4245_id[] = {
-       { "ltc4245", ltc4245 },
+       { "ltc4245", 0 },
        { }
 };
 MODULE_DEVICE_TABLE(i2c, ltc4245_id);
 
 /* This is the driver that will be inserted */
 static struct i2c_driver ltc4245_driver = {
-       .class          = I2C_CLASS_HWMON,
        .driver = {
                .name   = "ltc4245",
        },
        .probe          = ltc4245_probe,
        .remove         = ltc4245_remove,
        .id_table       = ltc4245_id,
-       .detect         = ltc4245_detect,
-       .address_data   = &addr_data,
 };
 
 static int __init ltc4245_init(void)