#include <asm/mach/time.h>
#include <plat/mtu.h>
-#include <plat/pincfg.h>
#include <linux/platform_data/mtd-nomadik-nand.h>
#include <mach/fsmc.h>
#include <linux/i2c-gpio.h>
#include <linux/platform_device.h>
#include <linux/platform_data/pinctrl-nomadik.h>
-#include <plat/pincfg.h>
/*
* There are two busses in the 8815NHK.
#include <linux/gpio.h>
#include <linux/platform_data/pinctrl-nomadik.h>
-#include <plat/pincfg.h>
#include <plat/ste_dma40.h>
#include <mach/devices.h>
#include <linux/platform_data/pinctrl-nomadik.h>
#include <asm/mach-types.h>
-#include <plat/pincfg.h>
#include <mach/hardware.h>
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License terms: GNU General Public License, version 2
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- *
- * Based on arch/arm/mach-pxa/include/mach/mfp.h:
- * Copyright (C) 2007 Marvell International Ltd.
- * eric miao <eric.miao@marvell.com>
- */
-
-#ifndef __PLAT_PINCFG_H
-#define __PLAT_PINCFG_H
-
-/*
- * pin configurations are represented by 32-bit integers:
- *
- * bit 0.. 8 - Pin Number (512 Pins Maximum)
- * bit 9..10 - Alternate Function Selection
- * bit 11..12 - Pull up/down state
- * bit 13 - Sleep mode behaviour
- * bit 14 - Direction
- * bit 15 - Value (if output)
- * bit 16..18 - SLPM pull up/down state
- * bit 19..20 - SLPM direction
- * bit 21..22 - SLPM Value (if output)
- * bit 23..25 - PDIS value (if input)
- * bit 26 - Gpio mode
- * bit 27 - Sleep mode
- *
- * to facilitate the definition, the following macros are provided
- *
- * PIN_CFG_DEFAULT - default config (0):
- * pull up/down = disabled
- * sleep mode = input/wakeup
- * direction = input
- * value = low
- * SLPM direction = same as normal
- * SLPM pull = same as normal
- * SLPM value = same as normal
- *
- * PIN_CFG - default config with alternate function
- */
-
-typedef unsigned long pin_cfg_t;
-
-#define PIN_NUM_MASK 0x1ff
-#define PIN_NUM(x) ((x) & PIN_NUM_MASK)
-
-#define PIN_ALT_SHIFT 9
-#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT)
-#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT)
-#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT)
-#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT)
-#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT)
-#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT)
-
-#define PIN_PULL_SHIFT 11
-#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT)
-#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT)
-#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT)
-#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT)
-#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT)
-
-#define PIN_SLPM_SHIFT 13
-#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT)
-#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
-#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
-#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
-/* These two replace the above in DB8500v2+ */
-#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
-#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
-#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE
-
-#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */
-#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */
-
-#define PIN_DIR_SHIFT 14
-#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT)
-#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
-#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT)
-#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT)
-
-#define PIN_VAL_SHIFT 15
-#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT)
-#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
-#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT)
-#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT)
-
-#define PIN_SLPM_PULL_SHIFT 16
-#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL(x) \
- (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL_NONE \
- ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL_UP \
- ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT)
-#define PIN_SLPM_PULL_DOWN \
- ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT)
-
-#define PIN_SLPM_DIR_SHIFT 19
-#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT)
-#define PIN_SLPM_DIR(x) \
- (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT)
-#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT)
-#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT)
-
-#define PIN_SLPM_VAL_SHIFT 21
-#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT)
-#define PIN_SLPM_VAL(x) \
- (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT)
-#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT)
-#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT)
-
-#define PIN_SLPM_PDIS_SHIFT 23
-#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS(x) \
- (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT)
-#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT)
-
-#define PIN_LOWEMI_SHIFT 25
-#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT)
-#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT)
-#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT)
-#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT)
-
-#define PIN_GPIOMODE_SHIFT 26
-#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT)
-#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT)
-#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT)
-#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT)
-
-#define PIN_SLEEPMODE_SHIFT 27
-#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT)
-#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT)
-#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT)
-#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT)
-
-
-/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */
-#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN)
-#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP)
-#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE)
-#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW)
-#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH)
-
-#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN)
-#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP)
-#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE)
-#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW)
-#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH)
-
-#define PIN_CFG_DEFAULT (0)
-
-#define PIN_CFG(num, alt) \
- (PIN_CFG_DEFAULT |\
- (PIN_NUM(num) | PIN_##alt))
-
-#define PIN_CFG_INPUT(num, alt, pull) \
- (PIN_CFG_DEFAULT |\
- (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull))
-
-#define PIN_CFG_OUTPUT(num, alt, val) \
- (PIN_CFG_DEFAULT |\
- (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val))
-
-extern int nmk_config_pin(pin_cfg_t cfg, bool sleep);
-extern int nmk_config_pins(pin_cfg_t *cfgs, int num);
-extern int nmk_config_pins_sleep(pin_cfg_t *cfgs, int num);
-
-#endif
#include <asm/mach/irq.h>
-#include <plat/pincfg.h>
-
#include "pinctrl-nomadik.h"
/*
* and its sleep mode based on the specified configuration. The @cfg is
* usually one of the SoC specific macros defined in mach/<soc>-pins.h. These
* are constructed using, and can be further enhanced with, the macros in
- * plat/pincfg.h.
+ * <linux/platform_data/pinctrl-nomadik.h>
*
* If a pin's mode is set to GPIO, it is configured as an input to avoid
* side-effects. The gpio can be manipulated later using standard GPIO API
#ifndef __PLAT_NOMADIK_GPIO
#define __PLAT_NOMADIK_GPIO
+/*
+ * pin configurations are represented by 32-bit integers:
+ *
+ * bit 0.. 8 - Pin Number (512 Pins Maximum)
+ * bit 9..10 - Alternate Function Selection
+ * bit 11..12 - Pull up/down state
+ * bit 13 - Sleep mode behaviour
+ * bit 14 - Direction
+ * bit 15 - Value (if output)
+ * bit 16..18 - SLPM pull up/down state
+ * bit 19..20 - SLPM direction
+ * bit 21..22 - SLPM Value (if output)
+ * bit 23..25 - PDIS value (if input)
+ * bit 26 - Gpio mode
+ * bit 27 - Sleep mode
+ *
+ * to facilitate the definition, the following macros are provided
+ *
+ * PIN_CFG_DEFAULT - default config (0):
+ * pull up/down = disabled
+ * sleep mode = input/wakeup
+ * direction = input
+ * value = low
+ * SLPM direction = same as normal
+ * SLPM pull = same as normal
+ * SLPM value = same as normal
+ *
+ * PIN_CFG - default config with alternate function
+ */
+
+typedef unsigned long pin_cfg_t;
+
+#define PIN_NUM_MASK 0x1ff
+#define PIN_NUM(x) ((x) & PIN_NUM_MASK)
+
+#define PIN_ALT_SHIFT 9
+#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT)
+#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT)
+#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT)
+#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT)
+#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT)
+#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT)
+
+#define PIN_PULL_SHIFT 11
+#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT)
+#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT)
+#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT)
+#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT)
+#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT)
+
+#define PIN_SLPM_SHIFT 13
+#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT)
+#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
+#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
+#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
+/* These two replace the above in DB8500v2+ */
+#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE
+
+#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */
+#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */
+
+#define PIN_DIR_SHIFT 14
+#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT)
+#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
+#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT)
+#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT)
+
+#define PIN_VAL_SHIFT 15
+#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT)
+#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
+#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT)
+#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT)
+
+#define PIN_SLPM_PULL_SHIFT 16
+#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL(x) \
+ (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_NONE \
+ ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_UP \
+ ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_DOWN \
+ ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT)
+
+#define PIN_SLPM_DIR_SHIFT 19
+#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR(x) \
+ (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT)
+
+#define PIN_SLPM_VAL_SHIFT 21
+#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL(x) \
+ (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT)
+
+#define PIN_SLPM_PDIS_SHIFT 23
+#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS(x) \
+ (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT)
+
+#define PIN_LOWEMI_SHIFT 25
+#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT)
+
+#define PIN_GPIOMODE_SHIFT 26
+#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT)
+
+#define PIN_SLEEPMODE_SHIFT 27
+#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT)
+
+
+/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */
+#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN)
+#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP)
+#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE)
+#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW)
+#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH)
+
+#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN)
+#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP)
+#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE)
+#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW)
+#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH)
+
+#define PIN_CFG_DEFAULT (0)
+
+#define PIN_CFG(num, alt) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt))
+
+#define PIN_CFG_INPUT(num, alt, pull) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull))
+
+#define PIN_CFG_OUTPUT(num, alt, val) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val))
+
/*
* "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
* the "gpio" namespace for generic and cross-machine functions
NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE,
};
+/* Older deprecated pin config API that should go away soon */
+extern int nmk_config_pin(pin_cfg_t cfg, bool sleep);
+extern int nmk_config_pins(pin_cfg_t *cfgs, int num);
+extern int nmk_config_pins_sleep(pin_cfg_t *cfgs, int num);
extern int nmk_gpio_set_slpm(int gpio, enum nmk_gpio_slpm mode);
extern int nmk_gpio_set_pull(int gpio, enum nmk_gpio_pull pull);
#ifdef CONFIG_PINCTRL_NOMADIK
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff