i2c: s3c2410: Add support for pinctrl
authorTomasz Figa <t.figa@samsung.com>
Tue, 13 Nov 2012 10:33:40 +0000 (11:33 +0100)
committerWolfram Sang <w.sang@pengutronix.de>
Fri, 16 Nov 2012 11:53:25 +0000 (12:53 +0100)
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Documentation/devicetree/bindings/i2c/samsung-i2c.txt
drivers/i2c/busses/i2c-s3c2410.c

index b6cb5a12c672e9eb430534b3bb15dbb25ca83871..e9611ace87924b8131295831103cb1ba0f3372f7 100644 (file)
@@ -13,11 +13,17 @@ Required properties:
   - interrupts: interrupt number to the cpu.
   - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
 
+Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
+  - Samsung GPIO variant (deprecated):
+    - gpios: The order of the gpios should be the following: <SDA, SCL>.
+      The gpio specifier depends on the gpio controller. Required in all
+      cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+      lines are permanently wired to the respective clienta
+  - Pinctrl variant (preferred, if available):
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
 Optional properties:
-  - gpios: The order of the gpios should be the following: <SDA, SCL>.
-    The gpio specifier depends on the gpio controller. Required in all
-    cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
-    lines are permanently wired to the respective client
   - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
     specified, default value is 0.
   - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
@@ -31,8 +37,14 @@ Example:
                interrupts = <345>;
                samsung,i2c-sda-delay = <100>;
                samsung,i2c-max-bus-freq = <100000>;
+               /* Samsung GPIO variant begins here */
                gpios = <&gpd1 2 0 /* SDA */
                         &gpd1 3 0 /* SCL */>;
+               /* Samsung GPIO variant ends here */
+               /* Pinctrl variant begins here */
+               pinctrl-0 = <&i2c3_bus>;
+               pinctrl-names = "default";
+               /* Pinctrl variant ends here */
                #address-cells = <1>;
                #size-cells = <0>;
 
index f82d11f9b8f2ceb30e79e0a148e64431f36c31ac..40e2d40bbdb5b72283a3fc21a176a3fda4977945 100644 (file)
@@ -38,6 +38,7 @@
 #include <linux/io.h>
 #include <linux/of_i2c.h>
 #include <linux/of_gpio.h>
+#include <linux/pinctrl/consumer.h>
 
 #include <asm/irq.h>
 
@@ -82,6 +83,7 @@ struct s3c24xx_i2c {
 
        struct s3c2410_platform_i2c     *pdata;
        int                     gpios[2];
+       struct pinctrl          *pctrl;
 #ifdef CONFIG_CPU_FREQ
        struct notifier_block   freq_transition;
 #endif
@@ -860,9 +862,8 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c)
 
        if (pdata->cfg_gpio)
                pdata->cfg_gpio(to_platform_device(i2c->dev));
-       else
-               if (s3c24xx_i2c_parse_dt_gpio(i2c))
-                       return -EINVAL;
+       else if (IS_ERR(i2c->pctrl) && s3c24xx_i2c_parse_dt_gpio(i2c))
+               return -EINVAL;
 
        /* write slave address */
 
@@ -1003,6 +1004,8 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev)
        i2c->adap.algo_data = i2c;
        i2c->adap.dev.parent = &pdev->dev;
 
+       i2c->pctrl = devm_pinctrl_get_select_default(i2c->dev);
+
        /* initialise the i2c controller */
 
        ret = s3c24xx_i2c_init(i2c);
@@ -1092,7 +1095,8 @@ static int s3c24xx_i2c_remove(struct platform_device *pdev)
        clk_disable_unprepare(i2c->clk);
        clk_put(i2c->clk);
 
-       s3c24xx_i2c_dt_gpio_free(i2c);
+       if (pdev->dev.of_node && IS_ERR(i2c->pctrl))
+               s3c24xx_i2c_dt_gpio_free(i2c);
 
        return 0;
 }