--- /dev/null
+* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge
+
+The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts
+a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C.
+
+Required Properties:
+
+- compatible: value should be "toshiba,tc358743"
+- clocks, clock-names: should contain a phandle link to the reference clock
+ source, the clock input is named "refclk".
+
+Optional Properties:
+
+- reset-gpios: gpio phandle GPIO connected to the reset pin
+- interrupts, interrupt-parent: GPIO connected to the interrupt pin
+- data-lanes: should be <1 2 3 4> for four-lane operation,
+ or <1 2> for two-lane operation
+- clock-lanes: should be <0>
+- clock-noncontinuous: Presence of this boolean property decides whether the
+ MIPI CSI-2 clock is continuous or non-continuous.
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+ expressed as a 64-bit big-endian integer. The frequency
+ is half of the bps per lane due to DDR transmission.
+
+For further information on the MIPI CSI-2 endpoint node properties, see
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+ tc358743@0f {
+ compatible = "toshiba,tc358743";
+ reg = <0x0f>;
+ clocks = <&hdmi_osc>;
+ clock-names = "refclk";
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+ port {
+ tc358743_out: endpoint {
+ remote-endpoint = <&mipi_csi2_in>;
+ data-lanes = <1 2 3 4>;
+ clock-lanes = <0>;
+ clock-noncontinuous;
+ link-frequencies = /bits/ 64 <297000000>;
+ };
+ };
+ };
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/i2c.h>
+#include <linux/clk.h>
#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
#include <linux/videodev2.h>
#include <linux/workqueue.h>
#include <linux/v4l2-dv-timings.h>
#include <media/v4l2-dv-timings.h>
#include <media/v4l2-device.h>
#include <media/v4l2-ctrls.h>
+#include <media/v4l2-of.h>
#include <media/tc358743.h>
#include "tc358743_regs.h"
struct tc358743_state {
struct tc358743_platform_data pdata;
+ struct v4l2_of_bus_mipi_csi2 bus;
struct v4l2_subdev sd;
struct media_pad pad;
struct v4l2_ctrl_handler hdl;
struct v4l2_dv_timings timings;
u32 mbus_fmt_code;
+
+ struct gpio_desc *reset_gpio;
};
static void tc358743_enable_interrupts(struct v4l2_subdev *sd,
((lanes > 2) ? MASK_D2M_HSTXVREGEN : 0x0) |
((lanes > 3) ? MASK_D3M_HSTXVREGEN : 0x0));
- i2c_wr32(sd, TXOPTIONCNTRL, MASK_CONTCLKMODE);
+ i2c_wr32(sd, TXOPTIONCNTRL, (state->bus.flags &
+ V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) ? MASK_CONTCLKMODE : 0);
i2c_wr32(sd, STARTCNTRL, MASK_START);
i2c_wr32(sd, CSI_START, MASK_STRT);
/* --------------- PROBE / REMOVE --------------- */
+#ifdef CONFIG_OF
+static void tc358743_gpio_reset(struct tc358743_state *state)
+{
+ gpiod_set_value(state->reset_gpio, 0);
+ usleep_range(5000, 10000);
+ gpiod_set_value(state->reset_gpio, 1);
+ usleep_range(1000, 2000);
+ gpiod_set_value(state->reset_gpio, 0);
+ msleep(20);
+}
+
+static int tc358743_probe_of(struct tc358743_state *state)
+{
+ struct device *dev = &state->i2c_client->dev;
+ struct v4l2_of_endpoint *endpoint;
+ struct device_node *ep;
+ struct clk *refclk;
+ u32 bps_pr_lane;
+ int ret = -EINVAL;
+
+ refclk = devm_clk_get(dev, "refclk");
+ if (IS_ERR(refclk)) {
+ if (PTR_ERR(refclk) != -EPROBE_DEFER)
+ dev_err(dev, "failed to get refclk: %ld\n",
+ PTR_ERR(refclk));
+ return PTR_ERR(refclk);
+ }
+
+ ep = of_graph_get_next_endpoint(dev->of_node, NULL);
+ if (!ep) {
+ dev_err(dev, "missing endpoint node\n");
+ return -EINVAL;
+ }
+
+ endpoint = v4l2_of_alloc_parse_endpoint(ep);
+ if (IS_ERR(endpoint)) {
+ dev_err(dev, "failed to parse endpoint\n");
+ return PTR_ERR(endpoint);
+ }
+
+ if (endpoint->bus_type != V4L2_MBUS_CSI2 ||
+ endpoint->bus.mipi_csi2.num_data_lanes == 0 ||
+ endpoint->nr_of_link_frequencies == 0) {
+ dev_err(dev, "missing CSI-2 properties in endpoint\n");
+ goto free_endpoint;
+ }
+
+ state->bus = endpoint->bus.mipi_csi2;
+
+ clk_prepare_enable(refclk);
+
+ state->pdata.refclk_hz = clk_get_rate(refclk);
+ state->pdata.ddc5v_delay = DDC5V_DELAY_100_MS;
+ state->pdata.enable_hdcp = false;
+ /* A FIFO level of 16 should be enough for 2-lane 720p60 at 594 MHz. */
+ state->pdata.fifo_level = 16;
+ /*
+ * The PLL input clock is obtained by dividing refclk by pll_prd.
+ * It must be between 6 MHz and 40 MHz, lower frequency is better.
+ */
+ switch (state->pdata.refclk_hz) {
+ case 26000000:
+ case 27000000:
+ case 42000000:
+ state->pdata.pll_prd = state->pdata.refclk_hz / 6000000;
+ break;
+ default:
+ dev_err(dev, "unsupported refclk rate: %u Hz\n",
+ state->pdata.refclk_hz);
+ goto disable_clk;
+ }
+
+ /*
+ * The CSI bps per lane must be between 62.5 Mbps and 1 Gbps.
+ * The default is 594 Mbps for 4-lane 1080p60 or 2-lane 720p60.
+ */
+ bps_pr_lane = 2 * endpoint->link_frequencies[0];
+ if (bps_pr_lane < 62500000U || bps_pr_lane > 1000000000U) {
+ dev_err(dev, "unsupported bps per lane: %u bps\n", bps_pr_lane);
+ goto disable_clk;
+ }
+
+ /* The CSI speed per lane is refclk / pll_prd * pll_fbd */
+ state->pdata.pll_fbd = bps_pr_lane /
+ state->pdata.refclk_hz * state->pdata.pll_prd;
+
+ /*
+ * FIXME: These timings are from REF_02 for 594 Mbps per lane (297 MHz
+ * link frequency). In principle it should be possible to calculate
+ * them based on link frequency and resolution.
+ */
+ if (bps_pr_lane != 594000000U)
+ dev_warn(dev, "untested bps per lane: %u bps\n", bps_pr_lane);
+ state->pdata.lineinitcnt = 0xe80;
+ state->pdata.lptxtimecnt = 0x003;
+ /* tclk-preparecnt: 3, tclk-zerocnt: 20 */
+ state->pdata.tclk_headercnt = 0x1403;
+ state->pdata.tclk_trailcnt = 0x00;
+ /* ths-preparecnt: 3, ths-zerocnt: 1 */
+ state->pdata.ths_headercnt = 0x0103;
+ state->pdata.twakeup = 0x4882;
+ state->pdata.tclk_postcnt = 0x008;
+ state->pdata.ths_trailcnt = 0x2;
+ state->pdata.hstxvregcnt = 0;
+
+ state->reset_gpio = devm_gpiod_get(dev, "reset");
+ if (IS_ERR(state->reset_gpio)) {
+ dev_err(dev, "failed to get reset gpio\n");
+ ret = PTR_ERR(state->reset_gpio);
+ goto disable_clk;
+ }
+
+ tc358743_gpio_reset(state);
+
+ ret = 0;
+ goto free_endpoint;
+
+disable_clk:
+ clk_disable_unprepare(refclk);
+free_endpoint:
+ v4l2_of_free_endpoint(endpoint);
+ return ret;
+}
+#else
+static inline int tc358743_probe_of(struct tc358743_state *state)
+{
+ return -ENODEV;
+}
+#endif
+
static int tc358743_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
if (!state)
return -ENOMEM;
+ state->i2c_client = client;
+
/* platform data */
- if (!pdata) {
- v4l_err(client, "No platform data!\n");
- return -ENODEV;
+ if (pdata) {
+ state->pdata = *pdata;
+ state->bus.flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK;
+ } else {
+ err = tc358743_probe_of(state);
+ if (err == -ENODEV)
+ v4l_err(client, "No platform data!\n");
+ if (err)
+ return err;
}
- state->pdata = *pdata;
- state->i2c_client = client;
sd = &state->sd;
v4l2_i2c_subdev_init(sd, client, &tc358743_ops);
sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff