data = ac97c_readl(atmel_wm97xx, CBRHR);
value = data & 0x0fff;
- source = data & WM97XX_ADCSRC_MASK;
+ source = data & WM97XX_ADCSEL_MASK;
pen_down = (data & WM97XX_PEN_DOWN) >> 8;
if (source == WM97XX_ADCSEL_X)
x, y, p);
/* are samples valid */
- if ((x & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_X ||
- (y & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_Y ||
- (p & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_PRES)
+ if ((x & WM97XX_ADCSEL_MASK) != WM97XX_ADCSEL_X ||
+ (y & WM97XX_ADCSEL_MASK) != WM97XX_ADCSEL_Y ||
+ (p & WM97XX_ADCSEL_MASK) != WM97XX_ADCSEL_PRES)
goto up;
/* coordinate is good */
wm->mach_ops->post_sample(adcsel);
/* check we have correct sample */
- if ((*sample & WM97XX_ADCSRC_MASK) != ffs(adcsel >> 1) << 12) {
+ if ((*sample & WM97XX_ADCSEL_MASK) != ffs(adcsel >> 1) << 12) {
dev_dbg(wm->dev, "adc wrong sample, read %x got %x", adcsel,
- *sample & WM97XX_ADCSRC_MASK);
+ *sample & WM97XX_ADCSEL_MASK);
return RC_PENUP;
}
x, y, p);
/* are samples valid */
- if ((x & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_X ||
- (y & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_Y ||
- (p & WM97XX_ADCSRC_MASK) != WM97XX_ADCSEL_PRES)
+ if ((x & WM97XX_ADCSEL_MASK) != WM97XX_ADCSEL_X ||
+ (y & WM97XX_ADCSEL_MASK) != WM97XX_ADCSEL_Y ||
+ (p & WM97XX_ADCSEL_MASK) != WM97XX_ADCSEL_PRES)
goto up;
/* coordinate is good */
#define WM97XX_ADCSEL_X 0x1000 /* x coord measurement */
#define WM97XX_ADCSEL_Y 0x2000 /* y coord measurement */
#define WM97XX_ADCSEL_PRES 0x3000 /* pressure measurement */
-#define WM97XX_ADCSEL_MASK 0x7000
+#define WM97XX_ADCSEL_MASK 0x7000 /* ADC selection mask */
#define WM97XX_COO 0x0800 /* enable coordinate mode */
#define WM97XX_CTC 0x0400 /* enable continuous mode */
#define WM97XX_CM_RATE_93 0x0000 /* 93.75Hz continuous rate */
#define WM97XX_PRP_DET_DIG 0xc000 /* setect on, digitise on */
#define WM97XX_RPR 0x2000 /* wake up on pen down */
#define WM97XX_PEN_DOWN 0x8000 /* pen is down */
-#define WM97XX_ADCSRC_MASK 0x7000 /* ADC source mask */
#define WM97XX_AUX_ID1 0x8001
#define WM97XX_AUX_ID2 0x8002