[ARM] 4353/1: AT91: Support ADS7846 touchsceen on SAM9261-EK board
authorAndrew Victor <andrew@sanpeople.com>
Wed, 2 May 2007 16:58:51 +0000 (17:58 +0100)
committerRussell King <rmk+kernel@arm.linux.org.uk>
Thu, 3 May 2007 13:10:23 +0000 (14:10 +0100)
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9261-EK board.

Original patch by Morten Larsen.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/board-sam9261ek.c

index b7e772467cf6bb056f1d582a39e9fdf96fde718a..bcf71536cc6db2931bf8a220548146ad1b2806c5 100644 (file)
@@ -25,6 +25,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
 #include <linux/dm9000.h>
 
 #include <asm/hardware.h>
@@ -194,6 +195,41 @@ static struct at91_nand_data __initdata ek_nand_data = {
 #endif
 };
 
+/*
+ * ADS7846 Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+
+static int ads7843_pendown_state(void)
+{
+       return !at91_get_gpio_value(AT91_PIN_PC2);      /* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+       .model                  = 7843,
+       .x_min                  = 150,
+       .x_max                  = 3830,
+       .y_min                  = 190,
+       .y_max                  = 3830,
+       .vref_delay_usecs       = 100,
+       .x_plate_ohms           = 450,
+       .y_plate_ohms           = 250,
+       .pressure_max           = 15000,
+       .debounce_max           = 1,
+       .debounce_rep           = 0,
+       .debounce_tol           = (~0),
+       .get_pendown_state      = ads7843_pendown_state,
+};
+
+static void __init ek_add_device_ts(void)
+{
+       at91_set_B_periph(AT91_PIN_PC2, 1);     /* External IRQ0, with pullup */
+       at91_set_gpio_input(AT91_PIN_PA11, 1);  /* Touchscreen BUSY signal */
+}
+#else
+static void __init ek_add_device_ts(void) {}
+#endif
+
 /*
  * SPI devices
  */
@@ -204,6 +240,16 @@ static struct spi_board_info ek_spi_devices[] = {
                .max_speed_hz   = 15 * 1000 * 1000,
                .bus_num        = 0,
        },
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+       {
+               .modalias       = "ads7846",
+               .chip_select    = 2,
+               .max_speed_hz   = 125000 * 26,  /* (max sample rate @ 3V) * (cmd + data + overhead) */
+               .bus_num        = 0,
+               .platform_data  = &ads_info,
+               .irq            = AT91SAM9261_ID_IRQ0,
+       },
+#endif
 #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
        {       /* DataFlash card - jumper (J12) configurable to CS3 or CS0 */
                .modalias       = "mtd_dataflash",
@@ -211,9 +257,9 @@ static struct spi_board_info ek_spi_devices[] = {
                .max_speed_hz   = 15 * 1000 * 1000,
                .bus_num        = 0,
        },
-#elif defined(CONFIG_SND_AT73C213)
+#elif defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
        {       /* AT73C213 DAC */
-               .modalias       = "snd_at73c213",
+               .modalias       = "at73c213",
                .chip_select    = 3,
                .max_speed_hz   = 10 * 1000 * 1000,
                .bus_num        = 0,
@@ -241,6 +287,8 @@ static void __init ek_board_init(void)
 #if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
        /* SPI */
        at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+       /* Touchscreen */
+       ek_add_device_ts();
 #else
        /* MMC */
        at91_add_device_mmc(0, &ek_mmc_data);