#include "iwl-commands.h"
-/*This files includes all the types / functions that are exported by the
- * upper layer to the bus and transport layer */
+/**
+ * DOC: shared area - role and goal
+ *
+ * The shared area contains all the data exported by the upper layer to the
+ * other layers. Since the bus and transport layer shouldn't dereference
+ * iwl_priv, all the data needed by the upper layer and the transport / bus
+ * layer must be here.
+ * The shared area also holds pointer to all the other layers. This allows a
+ * layer to call a function from another layer.
+ *
+ * NOTE: All the layers hold a pointer to the shared area which must be shrd.
+ * A few macros assume that (_m)->shrd points to the shared area no matter
+ * what _m is.
+ *
+ * gets notifications about enumeration, suspend, resume.
+ * For the moment, the bus layer is not a linux kernel module as itself, and
+ * the module_init function of the driver must call the bus specific
+ * registration functions. These functions are listed at the end of this file.
+ * For the moment, there is only one implementation of this interface: PCI-e.
+ * This implementation is iwl-pci.c
+ */
struct iwl_cfg;
struct iwl_bus;
/**
* struct iwl_mod_params
+ *
+ * Holds the module parameters
+ *
* @sw_crypto: using hardware encryption, default = 0
* @num_of_queues: number of tx queue, HW dependent
* @disable_11n: 11n capabilities enabled, default = 0
/**
* struct iwl_hw_params
+ *
+ * Holds the module parameters
+ *
* @max_txq_num: Max # Tx queues supported
* @num_ampdu_queues: num of ampdu queues
- * @tx/rx_chains_num: Number of TX/RX chains
- * @valid_tx/rx_ant: usable antennas
- * @max_stations:
- * @ht40_channel: is 40MHz width possible in band 2.4
+ * @tx_chains_num: Number of TX chains
+ * @rx_chains_num: Number of RX chains
+ * @valid_tx_ant: usable antennas for TX
+ * @valid_rx_ant: usable antennas for RX
+ * @max_stations: the maximal number of stations
+ * @ht40_channel: is 40MHz width possible: BIT(IEEE80211_BAND_XXX)
* @beacon_time_tsf_bits: number of valid tsf bits for beacon time
- * @sku:
+ * @sku: sku read from EEPROM
* @rx_page_order: Rx buffer page order
- * @rx_wrt_ptr_reg: FH{39}_RSCSR_CHNL0_WPTR
- * BIT(IEEE80211_BAND_5GHZ) BIT(IEEE80211_BAND_5GHZ)
- * @sw_crypto: 0 for hw, 1 for sw
- * @max_xxx_size: for ucode uses
- * @ct_kill_threshold: temperature threshold
+ * @max_inst_size: for ucode use
+ * @max_data_size: for ucode use
+ * @ct_kill_threshold: temperature threshold - in hw dependent unit
+ * @ct_kill_exit_threshold: when to reeable the device - in hw dependent unit
+ * relevant for 1000, 6000 and up
* @wd_timeout: TX queues watchdog timeout
* @calib_init_cfg: setup initial calibrations for the hw
* @calib_rt_cfg: setup runtime calibrations for the hw
u32 rx_page_order;
u32 max_inst_size;
u32 max_data_size;
- u32 ct_kill_threshold; /* value in hw-dependent units */
- u32 ct_kill_exit_threshold; /* value in hw-dependent units */
- /* for 1000, 6000 series and up */
+ u32 ct_kill_threshold;
+ u32 ct_kill_exit_threshold;
unsigned int wd_timeout;
u32 calib_init_cfg;
};
/**
- * struct iwl_ht_agg - aggregation status while waiting for block-ack
- * @txq_id: Tx queue used for Tx attempt
- * @wait_for_ba: Expect block-ack before next Tx reply
- * @rate_n_flags: Rate at which Tx was attempted
+ * enum iwl_agg_state
+ *
+ * The state machine of the BA agreement establishment / tear down.
+ * These states relate to a specific RA / TID.
*
- * If REPLY_TX indicates that aggregation was attempted, driver must wait
- * for block ack (REPLY_COMPRESSED_BA). This struct stores tx reply info
- * until block ack arrives.
+ * @IWL_AGG_OFF: aggregation is not used
+ * @IWL_AGG_ON: aggregation session is up
+ * @IWL_EMPTYING_HW_QUEUE_ADDBA: establishing a BA session - waiting for the
+ * HW queue to be empty from packets for this RA /TID.
+ * @IWL_EMPTYING_HW_QUEUE_DELBA: tearing down a BA session - waiting for the
+ * HW queue to be empty from packets for this RA /TID.
+ */
+enum iwl_agg_state {
+ IWL_AGG_OFF = 0,
+ IWL_AGG_ON,
+ IWL_EMPTYING_HW_QUEUE_ADDBA,
+ IWL_EMPTYING_HW_QUEUE_DELBA,
+};
+
+/**
+ * struct iwl_ht_agg - aggregation state machine
+
+ * This structs holds the states for the BA agreement establishment and tear
+ * down. It also holds the state during the BA session itself. This struct is
+ * duplicated for each RA / TID.
+
+ * @rate_n_flags: Rate at which Tx was attempted. Holds the data between the
+ * Tx response (REPLY_TX), and the block ack notification
+ * (REPLY_COMPRESSED_BA).
+ * @state: state of the BA agreement establishment / tear down.
+ * @txq_id: Tx queue used by the BA session - used by the transport layer.
+ * Needed by the upper layer for debugfs only.
+ * @wait_for_ba: Expect block-ack before next Tx reply
*/
struct iwl_ht_agg {
- u16 txq_id;
- u16 wait_for_ba;
u32 rate_n_flags;
-#define IWL_AGG_OFF 0
-#define IWL_AGG_ON 1
-#define IWL_EMPTYING_HW_QUEUE_ADDBA 2
-#define IWL_EMPTYING_HW_QUEUE_DELBA 3
- u8 state;
+ enum iwl_agg_state state;
+ u16 txq_id;
+ bool wait_for_ba;
};
+/**
+ * struct iwl_tid_data - one for each RA / TID
+
+ * This structs holds the states for each RA / TID.
+
+ * @seq_number: the next WiFi sequence number to use
+ * @tfds_in_queue: number of packets sent to the HW queues.
+ * Exported for debugfs only
+ * @agg: aggregation state machine
+ */
struct iwl_tid_data {
- u16 seq_number; /* agn only */
+ u16 seq_number;
u16 tfds_in_queue;
struct iwl_ht_agg agg;
};
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff