bonding: allow arp_ip_targets on separate vlans to use arp validation
authorAndy Gospodarek <andy@greyhouse.net>
Mon, 14 Dec 2009 10:48:58 +0000 (10:48 +0000)
committerDavid S. Miller <davem@davemloft.net>
Mon, 4 Jan 2010 05:17:16 +0000 (21:17 -0800)
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation.  A configuration like this, now works:

BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
    link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
    inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
    inet6 fe80::213:21ff:febe:33e9/64 scope link
       valid_lft forever preferred_lft forever

Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)

Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1

Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30

Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/bonding/bond_main.c
net/8021q/vlan_core.c
net/core/dev.c

index 3f0071cfe56b3a06c6f53e4ca29503393a4c5d94..6a42a1453afa7805889fb26d925cacbebf136190 100644 (file)
@@ -2615,6 +2615,17 @@ static int bond_arp_rcv(struct sk_buff *skb, struct net_device *dev, struct pack
        unsigned char *arp_ptr;
        __be32 sip, tip;
 
+       if (dev->priv_flags & IFF_802_1Q_VLAN) {
+               /*
+                * When using VLANS and bonding, dev and oriv_dev may be
+                * incorrect if the physical interface supports VLAN
+                * acceleration.  With this change ARP validation now
+                * works for hosts only reachable on the VLAN interface.
+                */
+               dev = vlan_dev_real_dev(dev);
+               orig_dev = dev_get_by_index_rcu(dev_net(skb->dev),skb->skb_iif);
+       }
+
        if (!(dev->priv_flags & IFF_BONDING) || !(dev->flags & IFF_MASTER))
                goto out;
 
index e75a2f3b10af7721610af6adf0c42e5c7fec2192..c0316e0ca6e854724ccb6dc07e1441dd697e7277 100644 (file)
@@ -14,6 +14,7 @@ int __vlan_hwaccel_rx(struct sk_buff *skb, struct vlan_group *grp,
        if (skb_bond_should_drop(skb))
                goto drop;
 
+       skb->skb_iif = skb->dev->ifindex;
        __vlan_hwaccel_put_tag(skb, vlan_tci);
        skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK);
 
@@ -85,6 +86,7 @@ vlan_gro_common(struct napi_struct *napi, struct vlan_group *grp,
        if (skb_bond_should_drop(skb))
                goto drop;
 
+       skb->skb_iif = skb->dev->ifindex;
        __vlan_hwaccel_put_tag(skb, vlan_tci);
        skb->dev = vlan_group_get_device(grp, vlan_tci & VLAN_VID_MASK);
 
index a8d68cdedbbeccd70fba43141bab3db59778fee3..f9aa699ab6cb3aefae3248062a7259e9f3689819 100644 (file)
@@ -2495,12 +2495,26 @@ ncls:
        if (!skb)
                goto out;
 
+       /*
+        * Make sure frames received on VLAN interfaces stacked on
+        * bonding interfaces still make their way to any base bonding
+        * device that may have registered for a specific ptype.  The
+        * handler may have to adjust skb->dev and orig_dev.
+        *
+        * null_or_orig can be overloaded since it will not be set when
+        * using VLANs on top of bonding.  Putting it here prevents
+        * disturbing the ptype_all handlers above.
+        */
+       if ((skb->dev->priv_flags & IFF_802_1Q_VLAN) &&
+           (vlan_dev_real_dev(skb->dev)->priv_flags & IFF_BONDING)) {
+               null_or_orig = vlan_dev_real_dev(skb->dev);
+       }
+
        type = skb->protocol;
        list_for_each_entry_rcu(ptype,
                        &ptype_base[ntohs(type) & PTYPE_HASH_MASK], list) {
-               if (ptype->type == type &&
-                   (ptype->dev == null_or_orig || ptype->dev == skb->dev ||
-                    ptype->dev == orig_dev)) {
+               if (ptype->type == type && (ptype->dev == null_or_orig ||
+                    ptype->dev == skb->dev || ptype->dev == orig_dev)) {
                        if (pt_prev)
                                ret = deliver_skb(skb, pt_prev, orig_dev);
                        pt_prev = ptype;