width of 8 is assumed.
- ti,nand-ecc-opt: A string setting the ECC layout to use. One of:
- "sw" <deprecated> use "ham1" instead
+ "sw" 1-bit Hamming ecc code via software
"hw" <deprecated> use "ham1" instead
"hw-romcode" <deprecated> use "ham1" instead
"ham1" 1-bit Hamming ecc code
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-rockchip@lists.infradead.org
S: Maintained
+F: arch/arm/boot/dts/rk3*
F: arch/arm/mach-rockchip/
+F: drivers/clk/rockchip/
+F: drivers/i2c/busses/i2c-rk3x.c
F: drivers/*/*rockchip*
+F: drivers/*/*/*rockchip*
+F: sound/soc/rockchip/
ARM/SAMSUNG ARM ARCHITECTURES
M: Ben Dooks <ben-linux@fluff.org>
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio2: gpio@48055000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio3: gpio@48057000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio4: gpio@48059000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio5: gpio@4805b000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio6: gpio@4805d000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio7: gpio@48051000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
gpio8: gpio@48053000 {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
};
uart1: serial@4806a000 {
MX53_PAD_CSI0_DAT9__I2C1_SCL 0x400001ec
>;
};
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT5__GPIO5_23 0x1e4 /* IRQ */
+ >;
+ };
};
};
pmic: mc34708@8 {
compatible = "fsl,mc34708";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
reg = <0x08>;
interrupt-parent = <&gpio5>;
interrupts = <23 0x8>;
sound-spdif {
compatible = "fsl,imx-audio-spdif";
- model = "imx-spdif";
+ model = "On-board SPDIF";
/* IMX6 doesn't implement this yet */
spdif-controller = <&spdif>;
spdif-out;
};
&usbh1 {
+ disable-over-current;
vbus-supply = <®_usbh1_vbus>;
status = "okay";
};
&usbotg {
+ disable-over-current;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
vbus-supply = <®_usbotg_vbus>;
sound-spdif {
compatible = "fsl,imx-audio-spdif";
- model = "imx-spdif";
+ model = "Integrated SPDIF";
/* IMX6 doesn't implement this yet */
spdif-controller = <&spdif>;
spdif-out;
fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
};
+ pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
+ fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+ };
+
pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
};
- pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+ pinctrl_cubox_i_usbotg: cubox-i-usbotg {
/*
- * The Cubox-i pulls this low, but as it's pointless
+ * The Cubox-i pulls ID low, but as it's pointless
* leaving it as a pull-up, even if it is just 10uA.
*/
- fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
};
pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
};
&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cubox_i_usbh1>;
vbus-supply = <®_usbh1_vbus>;
status = "okay";
};
&usbotg {
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
+ pinctrl-0 = <&pinctrl_cubox_i_usbotg>;
vbus-supply = <®_usbotg_vbus>;
status = "okay";
};
enet {
pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b8b0
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
/* AR8035 reset */
MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
+ interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
};
&gpio1 {
#address-cells = <1>;
#size-cells = <1>;
reg = <1 0 0x08000000>;
- ti,nand-ecc-opt = "ham1";
+ ti,nand-ecc-opt = "sw";
nand-bus-width = <8>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <36>;
l3_iclk_div: l3_iclk_div {
#clock-cells = <0>;
- compatible = "fixed-factor-clock";
+ compatible = "ti,divider-clock";
+ ti,max-div = <2>;
+ ti,bit-shift = <4>;
+ reg = <0x100>;
clocks = <&dpll_core_h12x2_ck>;
- clock-mult = <1>;
- clock-div = <1>;
+ ti,index-power-of-two;
};
gpu_l3_iclk: gpu_l3_iclk {
l4_root_clk_div: l4_root_clk_div {
#clock-cells = <0>;
- compatible = "fixed-factor-clock";
+ compatible = "ti,divider-clock";
+ ti,max-div = <2>;
+ ti,bit-shift = <8>;
+ reg = <0x100>;
clocks = <&l3_iclk_div>;
- clock-mult = <1>;
- clock-div = <1>;
+ ti,index-power-of-two;
};
slimbus1_slimbus_clk: slimbus1_slimbus_clk {
regulator-always-on;
};
- clk32kg: regulator-clk32kg {
- compatible = "ti,twl6030-clk32kg";
- };
-
twl_usb_comparator: usb-comparator {
compatible = "ti,twl6030-usb";
interrupts = <4>, <10>;
ifeq ($(CONFIG_ARCH_BRCMSTB),y)
obj-y += brcmstb.o
-obj-$(CONFIG_SMP) += headsmp-brcmstb.o platsmp-brcmstb.o
endif
+++ /dev/null
-/*
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __BRCMSTB_H__
-#define __BRCMSTB_H__
-
-void brcmstb_secondary_startup(void);
-
-#endif /* __BRCMSTB_H__ */
+++ /dev/null
-/*
- * SMP boot code for secondary CPUs
- * Based on arch/arm/mach-tegra/headsmp.S
- *
- * Copyright (C) 2010 NVIDIA, Inc.
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <asm/assembler.h>
-#include <linux/linkage.h>
-#include <linux/init.h>
-
- .section ".text.head", "ax"
-
-ENTRY(brcmstb_secondary_startup)
- /*
- * Ensure CPU is in a sane state by disabling all IRQs and switching
- * into SVC mode.
- */
- setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
-
- bl v7_invalidate_l1
- b secondary_startup
-ENDPROC(brcmstb_secondary_startup)
+++ /dev/null
-/*
- * Broadcom STB CPU SMP and hotplug support for ARM
- *
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/of_address.h>
-#include <linux/of_platform.h>
-#include <linux/printk.h>
-#include <linux/regmap.h>
-#include <linux/smp.h>
-#include <linux/mfd/syscon.h>
-#include <linux/spinlock.h>
-
-#include <asm/cacheflush.h>
-#include <asm/cp15.h>
-#include <asm/mach-types.h>
-#include <asm/smp_plat.h>
-
-#include "brcmstb.h"
-
-enum {
- ZONE_MAN_CLKEN_MASK = BIT(0),
- ZONE_MAN_RESET_CNTL_MASK = BIT(1),
- ZONE_MAN_MEM_PWR_MASK = BIT(4),
- ZONE_RESERVED_1_MASK = BIT(5),
- ZONE_MAN_ISO_CNTL_MASK = BIT(6),
- ZONE_MANUAL_CONTROL_MASK = BIT(7),
- ZONE_PWR_DN_REQ_MASK = BIT(9),
- ZONE_PWR_UP_REQ_MASK = BIT(10),
- ZONE_BLK_RST_ASSERT_MASK = BIT(12),
- ZONE_PWR_OFF_STATE_MASK = BIT(25),
- ZONE_PWR_ON_STATE_MASK = BIT(26),
- ZONE_DPG_PWR_STATE_MASK = BIT(28),
- ZONE_MEM_PWR_STATE_MASK = BIT(29),
- ZONE_RESET_STATE_MASK = BIT(31),
- CPU0_PWR_ZONE_CTRL_REG = 1,
- CPU_RESET_CONFIG_REG = 2,
-};
-
-static void __iomem *cpubiuctrl_block;
-static void __iomem *hif_cont_block;
-static u32 cpu0_pwr_zone_ctrl_reg;
-static u32 cpu_rst_cfg_reg;
-static u32 hif_cont_reg;
-
-#ifdef CONFIG_HOTPLUG_CPU
-static DEFINE_PER_CPU_ALIGNED(int, per_cpu_sw_state);
-
-static int per_cpu_sw_state_rd(u32 cpu)
-{
- sync_cache_r(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
- return per_cpu(per_cpu_sw_state, cpu);
-}
-
-static void per_cpu_sw_state_wr(u32 cpu, int val)
-{
- per_cpu(per_cpu_sw_state, cpu) = val;
- dmb();
- sync_cache_w(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
- dsb_sev();
-}
-#else
-static inline void per_cpu_sw_state_wr(u32 cpu, int val) { }
-#endif
-
-static void __iomem *pwr_ctrl_get_base(u32 cpu)
-{
- void __iomem *base = cpubiuctrl_block + cpu0_pwr_zone_ctrl_reg;
- base += (cpu_logical_map(cpu) * 4);
- return base;
-}
-
-static u32 pwr_ctrl_rd(u32 cpu)
-{
- void __iomem *base = pwr_ctrl_get_base(cpu);
- return readl_relaxed(base);
-}
-
-static void pwr_ctrl_wr(u32 cpu, u32 val)
-{
- void __iomem *base = pwr_ctrl_get_base(cpu);
- writel(val, base);
-}
-
-static void cpu_rst_cfg_set(u32 cpu, int set)
-{
- u32 val;
- val = readl_relaxed(cpubiuctrl_block + cpu_rst_cfg_reg);
- if (set)
- val |= BIT(cpu_logical_map(cpu));
- else
- val &= ~BIT(cpu_logical_map(cpu));
- writel_relaxed(val, cpubiuctrl_block + cpu_rst_cfg_reg);
-}
-
-static void cpu_set_boot_addr(u32 cpu, unsigned long boot_addr)
-{
- const int reg_ofs = cpu_logical_map(cpu) * 8;
- writel_relaxed(0, hif_cont_block + hif_cont_reg + reg_ofs);
- writel_relaxed(boot_addr, hif_cont_block + hif_cont_reg + 4 + reg_ofs);
-}
-
-static void brcmstb_cpu_boot(u32 cpu)
-{
- pr_info("SMP: Booting CPU%d...\n", cpu);
-
- /*
- * set the reset vector to point to the secondary_startup
- * routine
- */
- cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
-
- /* unhalt the cpu */
- cpu_rst_cfg_set(cpu, 0);
-}
-
-static void brcmstb_cpu_power_on(u32 cpu)
-{
- /*
- * The secondary cores power was cut, so we must go through
- * power-on initialization.
- */
- u32 tmp;
-
- pr_info("SMP: Powering up CPU%d...\n", cpu);
-
- /* Request zone power up */
- pwr_ctrl_wr(cpu, ZONE_PWR_UP_REQ_MASK);
-
- /* Wait for the power up FSM to complete */
- do {
- tmp = pwr_ctrl_rd(cpu);
- } while (!(tmp & ZONE_PWR_ON_STATE_MASK));
-
- per_cpu_sw_state_wr(cpu, 1);
-}
-
-static int brcmstb_cpu_get_power_state(u32 cpu)
-{
- int tmp = pwr_ctrl_rd(cpu);
- return (tmp & ZONE_RESET_STATE_MASK) ? 0 : 1;
-}
-
-#ifdef CONFIG_HOTPLUG_CPU
-
-static void brcmstb_cpu_die(u32 cpu)
-{
- v7_exit_coherency_flush(all);
-
- /* Prevent all interrupts from reaching this CPU. */
- arch_local_irq_disable();
-
- /*
- * Final full barrier to ensure everything before this instruction has
- * quiesced.
- */
- isb();
- dsb();
-
- per_cpu_sw_state_wr(cpu, 0);
-
- /* Sit and wait to die */
- wfi();
-
- /* We should never get here... */
- panic("Spurious interrupt on CPU %d received!\n", cpu);
-}
-
-static int brcmstb_cpu_kill(u32 cpu)
-{
- u32 tmp;
-
- pr_info("SMP: Powering down CPU%d...\n", cpu);
-
- while (per_cpu_sw_state_rd(cpu))
- ;
-
- /* Program zone reset */
- pwr_ctrl_wr(cpu, ZONE_RESET_STATE_MASK | ZONE_BLK_RST_ASSERT_MASK |
- ZONE_PWR_DN_REQ_MASK);
-
- /* Verify zone reset */
- tmp = pwr_ctrl_rd(cpu);
- if (!(tmp & ZONE_RESET_STATE_MASK))
- pr_err("%s: Zone reset bit for CPU %d not asserted!\n",
- __func__, cpu);
-
- /* Wait for power down */
- do {
- tmp = pwr_ctrl_rd(cpu);
- } while (!(tmp & ZONE_PWR_OFF_STATE_MASK));
-
- /* Settle-time from Broadcom-internal DVT reference code */
- udelay(7);
-
- /* Assert reset on the CPU */
- cpu_rst_cfg_set(cpu, 1);
-
- return 1;
-}
-
-#endif /* CONFIG_HOTPLUG_CPU */
-
-static int __init setup_hifcpubiuctrl_regs(struct device_node *np)
-{
- int rc = 0;
- char *name;
- struct device_node *syscon_np = NULL;
-
- name = "syscon-cpu";
-
- syscon_np = of_parse_phandle(np, name, 0);
- if (!syscon_np) {
- pr_err("can't find phandle %s\n", name);
- rc = -EINVAL;
- goto cleanup;
- }
-
- cpubiuctrl_block = of_iomap(syscon_np, 0);
- if (!cpubiuctrl_block) {
- pr_err("iomap failed for cpubiuctrl_block\n");
- rc = -EINVAL;
- goto cleanup;
- }
-
- rc = of_property_read_u32_index(np, name, CPU0_PWR_ZONE_CTRL_REG,
- &cpu0_pwr_zone_ctrl_reg);
- if (rc) {
- pr_err("failed to read 1st entry from %s property (%d)\n", name,
- rc);
- rc = -EINVAL;
- goto cleanup;
- }
-
- rc = of_property_read_u32_index(np, name, CPU_RESET_CONFIG_REG,
- &cpu_rst_cfg_reg);
- if (rc) {
- pr_err("failed to read 2nd entry from %s property (%d)\n", name,
- rc);
- rc = -EINVAL;
- goto cleanup;
- }
-
-cleanup:
- if (syscon_np)
- of_node_put(syscon_np);
-
- return rc;
-}
-
-static int __init setup_hifcont_regs(struct device_node *np)
-{
- int rc = 0;
- char *name;
- struct device_node *syscon_np = NULL;
-
- name = "syscon-cont";
-
- syscon_np = of_parse_phandle(np, name, 0);
- if (!syscon_np) {
- pr_err("can't find phandle %s\n", name);
- rc = -EINVAL;
- goto cleanup;
- }
-
- hif_cont_block = of_iomap(syscon_np, 0);
- if (!hif_cont_block) {
- pr_err("iomap failed for hif_cont_block\n");
- rc = -EINVAL;
- goto cleanup;
- }
-
- /* offset is at top of hif_cont_block */
- hif_cont_reg = 0;
-
-cleanup:
- if (syscon_np)
- of_node_put(syscon_np);
-
- return rc;
-}
-
-static void __init brcmstb_cpu_ctrl_setup(unsigned int max_cpus)
-{
- int rc;
- struct device_node *np;
- char *name;
-
- name = "brcm,brcmstb-smpboot";
- np = of_find_compatible_node(NULL, NULL, name);
- if (!np) {
- pr_err("can't find compatible node %s\n", name);
- return;
- }
-
- rc = setup_hifcpubiuctrl_regs(np);
- if (rc)
- return;
-
- rc = setup_hifcont_regs(np);
- if (rc)
- return;
-}
-
-static DEFINE_SPINLOCK(boot_lock);
-
-static void brcmstb_secondary_init(unsigned int cpu)
-{
- /*
- * Synchronise with the boot thread.
- */
- spin_lock(&boot_lock);
- spin_unlock(&boot_lock);
-}
-
-static int brcmstb_boot_secondary(unsigned int cpu, struct task_struct *idle)
-{
- /*
- * set synchronisation state between this boot processor
- * and the secondary one
- */
- spin_lock(&boot_lock);
-
- /* Bring up power to the core if necessary */
- if (brcmstb_cpu_get_power_state(cpu) == 0)
- brcmstb_cpu_power_on(cpu);
-
- brcmstb_cpu_boot(cpu);
-
- /*
- * now the secondary core is starting up let it run its
- * calibrations, then wait for it to finish
- */
- spin_unlock(&boot_lock);
-
- return 0;
-}
-
-static struct smp_operations brcmstb_smp_ops __initdata = {
- .smp_prepare_cpus = brcmstb_cpu_ctrl_setup,
- .smp_secondary_init = brcmstb_secondary_init,
- .smp_boot_secondary = brcmstb_boot_secondary,
-#ifdef CONFIG_HOTPLUG_CPU
- .cpu_kill = brcmstb_cpu_kill,
- .cpu_die = brcmstb_cpu_die,
-#endif
-};
-
-CPU_METHOD_OF_DECLARE(brcmstb_smp, "brcm,brahma-b15", &brcmstb_smp_ops);
board_nand_data.nr_parts = nr_parts;
board_nand_data.devsize = nand_type;
- board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_HW;
+ board_nand_data.ecc_opt = OMAP_ECC_HAM1_CODE_SW;
gpmc_nand_init(&board_nand_data, gpmc_t);
}
#endif /* CONFIG_MTD_NAND_OMAP2 || CONFIG_MTD_NAND_OMAP2_MODULE */
return 0;
/* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */
- if (ecc_opt == OMAP_ECC_HAM1_CODE_HW)
+ if (ecc_opt == OMAP_ECC_HAM1_CODE_HW ||
+ ecc_opt == OMAP_ECC_HAM1_CODE_SW)
return 1;
else
return 0;
pr_err("%s: ti,nand-ecc-opt not found\n", __func__);
return -ENODEV;
}
- if (!strcmp(s, "ham1") || !strcmp(s, "sw") ||
- !strcmp(s, "hw") || !strcmp(s, "hw-romcode"))
+
+ if (!strcmp(s, "sw"))
+ gpmc_nand_data->ecc_opt = OMAP_ECC_HAM1_CODE_SW;
+ else if (!strcmp(s, "ham1") ||
+ !strcmp(s, "hw") || !strcmp(s, "hw-romcode"))
gpmc_nand_data->ecc_opt =
OMAP_ECC_HAM1_CODE_HW;
else if (!strcmp(s, "bch4"))
default:
/* Unknown default to latest silicon rev as default*/
- pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%d)\n",
+ pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n",
__func__, idcode, hawkeye, rev);
omap_revision = DRA752_REV_ES1_1;
}
r = clk_get_sys(dev_name(&od->pdev->dev), clk_alias);
if (!IS_ERR(r)) {
- dev_warn(&od->pdev->dev,
+ dev_dbg(&od->pdev->dev,
"alias %s already exists\n", clk_alias);
clk_put(r);
return;
oh->mux->pads_dynamic))) {
omap_hwmod_mux(oh->mux, _HWMOD_STATE_ENABLED);
_reconfigure_io_chain();
+ } else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+ _reconfigure_io_chain();
}
_add_initiator_dep(oh, mpu_oh);
if (oh->mux && oh->mux->pads_dynamic) {
omap_hwmod_mux(oh->mux, _HWMOD_STATE_IDLE);
_reconfigure_io_chain();
+ } else if (oh->flags & HWMOD_FORCE_MSTANDBY) {
+ _reconfigure_io_chain();
}
oh->_state = _HWMOD_STATE_IDLE;
if (!ois)
return 0;
+ if (ois[0] == NULL) /* Empty list */
+ return 0;
+
if (!linkspace) {
if (_alloc_linkspace(ois)) {
pr_err("omap_hwmod: could not allocate link space\n");
#include "i2c.h"
#include "mmc.h"
#include "wd_timer.h"
+#include "soc.h"
/* Base offset for all DRA7XX interrupts external to MPUSS */
#define DRA7XX_IRQ_GIC_START 32
&dra7xx_l4_per3__usb_otg_ss1,
&dra7xx_l4_per3__usb_otg_ss2,
&dra7xx_l4_per3__usb_otg_ss3,
- &dra7xx_l4_per3__usb_otg_ss4,
&dra7xx_l3_main_1__vcp1,
&dra7xx_l4_per2__vcp1,
&dra7xx_l3_main_1__vcp2,
NULL,
};
+static struct omap_hwmod_ocp_if *dra74x_hwmod_ocp_ifs[] __initdata = {
+ &dra7xx_l4_per3__usb_otg_ss4,
+ NULL,
+};
+
+static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
+ NULL,
+};
+
int __init dra7xx_hwmod_init(void)
{
+ int ret;
+
omap_hwmod_init();
- return omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+ ret = omap_hwmod_register_links(dra7xx_hwmod_ocp_ifs);
+
+ if (!ret && soc_is_dra74x())
+ return omap_hwmod_register_links(dra74x_hwmod_ocp_ifs);
+ else if (!ret && soc_is_dra72x())
+ return omap_hwmod_register_links(dra72x_hwmod_ocp_ifs);
+
+ return ret;
}
#define soc_is_omap54xx() 0
#define soc_is_omap543x() 0
#define soc_is_dra7xx() 0
+#define soc_is_dra74x() 0
+#define soc_is_dra72x() 0
#if defined(MULTI_OMAP2)
# if defined(CONFIG_ARCH_OMAP2)
#if defined(CONFIG_SOC_DRA7XX)
#undef soc_is_dra7xx
+#undef soc_is_dra74x
+#undef soc_is_dra72x
#define soc_is_dra7xx() (of_machine_is_compatible("ti,dra7"))
+#define soc_is_dra74x() (of_machine_is_compatible("ti,dra74"))
+#define soc_is_dra72x() (of_machine_is_compatible("ti,dra72"))
#endif
/* Various silicon revisions for omap2 */
static struct clk div4_clks[DIV4_NR] = {
[DIV4_SDH] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 8, 0x0dff, CLK_ENABLE_ON_INIT),
- [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1de0, CLK_ENABLE_ON_INIT),
- [DIV4_SD1] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 0, 0x1de0, CLK_ENABLE_ON_INIT),
+ [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1df0, CLK_ENABLE_ON_INIT),
+ [DIV4_SD1] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 0, 0x1df0, CLK_ENABLE_ON_INIT),
};
/* DIV6 clocks */
static struct clk div4_clks[DIV4_NR] = {
[DIV4_SDH] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 8, 0x0dff, CLK_ENABLE_ON_INIT),
- [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1de0, CLK_ENABLE_ON_INIT),
+ [DIV4_SD0] = SH_CLK_DIV4(&pll1_clk, SDCKCR, 4, 0x1df0, CLK_ENABLE_ON_INIT),
};
/* DIV6 clocks */
CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
CLKDEV_DEV_ID("e6cb0000.serial", &mstp_clks[MSTP207]), /* SCIFA5 */
CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]), /* SCIFB */
- CLKDEV_DEV_ID("0xe6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
+ CLKDEV_DEV_ID("e6c3000.serial", &mstp_clks[MSTP206]), /* SCIFB */
CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
CLKDEV_DEV_ID("e6c40000.serial", &mstp_clks[MSTP204]), /* SCIFA0 */
CLKDEV_DEV_ID("sh-sci.1", &mstp_clks[MSTP203]), /* SCIFA1 */
static int ve_init_opp_table(struct device *cpu_dev)
{
- int cluster = topology_physical_package_id(cpu_dev->id);
- int idx, ret = 0, max_opp = info->num_opps[cluster];
- struct ve_spc_opp *opps = info->opps[cluster];
+ int cluster;
+ int idx, ret = 0, max_opp;
+ struct ve_spc_opp *opps;
+
+ cluster = topology_physical_package_id(cpu_dev->id);
+ cluster = cluster < 0 ? 0 : cluster;
+
+ max_opp = info->num_opps[cluster];
+ opps = info->opps[cluster];
for (idx = 0; idx < max_opp; idx++, opps++) {
ret = dev_pm_opp_add(cpu_dev, opps->freq * 1000, opps->u_volt);
spc->hw.init = &init;
spc->cluster = topology_physical_package_id(cpu_dev->id);
+ spc->cluster = spc->cluster < 0 ? 0 : spc->cluster;
+
init.name = dev_name(cpu_dev);
init.ops = &clk_spc_ops;
init.flags = CLK_IS_ROOT | CLK_GET_RATE_NOCACHE;
u32 val;
val = readl(info->reg.gpmc_ecc_config);
- if (((val >> ECC_CONFIG_CS_SHIFT) & ~CS_MASK) != info->gpmc_cs)
+ if (((val >> ECC_CONFIG_CS_SHIFT) & CS_MASK) != info->gpmc_cs)
return -EINVAL;
/* read ecc result */
}
/* populate MTD interface based on ECC scheme */
- nand_chip->ecc.layout = &omap_oobinfo;
ecclayout = &omap_oobinfo;
switch (info->ecc_opt) {
+ case OMAP_ECC_HAM1_CODE_SW:
+ nand_chip->ecc.mode = NAND_ECC_SOFT;
+ break;
+
case OMAP_ECC_HAM1_CODE_HW:
pr_info("nand: using OMAP_ECC_HAM1_CODE_HW\n");
nand_chip->ecc.mode = NAND_ECC_HW;
nand_chip->ecc.priv = nand_bch_init(mtd,
nand_chip->ecc.size,
nand_chip->ecc.bytes,
- &nand_chip->ecc.layout);
+ &ecclayout);
if (!nand_chip->ecc.priv) {
pr_err("nand: error: unable to use s/w BCH library\n");
err = -EINVAL;
nand_chip->ecc.priv = nand_bch_init(mtd,
nand_chip->ecc.size,
nand_chip->ecc.bytes,
- &nand_chip->ecc.layout);
+ &ecclayout);
if (!nand_chip->ecc.priv) {
pr_err("nand: error: unable to use s/w BCH library\n");
err = -EINVAL;
goto return_error;
}
+ if (info->ecc_opt == OMAP_ECC_HAM1_CODE_SW)
+ goto scan_tail;
+
/* all OOB bytes from oobfree->offset till end off OOB are free */
ecclayout->oobfree->length = mtd->oobsize - ecclayout->oobfree->offset;
/* check if NAND device's OOB is enough to store ECC signatures */
err = -EINVAL;
goto return_error;
}
+ nand_chip->ecc.layout = ecclayout;
+scan_tail:
/* second phase scan */
if (nand_scan_tail(mtd)) {
err = -ENXIO;
};
enum omap_ecc {
- /* 1-bit ECC calculation by GPMC, Error detection by Software */
- OMAP_ECC_HAM1_CODE_HW = 0,
+ /*
+ * 1-bit ECC: calculation and correction by SW
+ * ECC stored at end of spare area
+ */
+ OMAP_ECC_HAM1_CODE_SW = 0,
+
+ /*
+ * 1-bit ECC: calculation by GPMC, Error detection by Software
+ * ECC layout compatible with ROM code layout
+ */
+ OMAP_ECC_HAM1_CODE_HW,
/* 4-bit ECC calculation by GPMC, Error detection by Software */
OMAP_ECC_BCH4_CODE_HW_DETECTION_SW,
/* 4-bit ECC calculation by GPMC, Error detection by ELM */
projects / GitHub / LineageOS / android_kernel_motorola_exynos9610.git / commitdiff