This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- snps,tx-sched-dwrr: Deficit Weighted Round Robin
- snps,tx-sched-sp: Strict priority
- For each TX queue
- - snps,weight: TX queue weight (if using a weighted algorithm)
-
+ - snps,weight: TX queue weight (if using a DCB weight algorithm)
+ - Choose one of these modes:
+ - snps,dcb-algorithm: TX queue will be working in DCB
+ - snps,avb-algorithm: TX queue will be working in AVB
+ - Configure Credit Base Shaper (if AVB Mode selected):
+ - snps,send_slope: enable Low Power Interface
+ - snps,idle_slope: unlock on WoL
+ - snps,high_credit: max write outstanding req. limit
+ - snps,low_credit: max read outstanding req. limit
Examples:
stmmac_axi_setup: stmmac-axi-config {
};
mtl_tx_setup: tx-queues-config {
- snps,tx-queues-to-use = <1>;
+ snps,tx-queues-to-use = <2>;
snps,tx-sched-wrr;
queue0 {
snps,weight = <0x10>;
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3E800>;
+ snps,low_credit = <0xFFC18000>;
};
};
u32 weight, u32 queue);
/* RX MTL queue to RX dma mapping */
void (*map_mtl_to_dma)(struct mac_device_info *hw, u32 queue, u32 chan);
+ /* Configure AV Algorithm */
+ void (*config_cbs)(struct mac_device_info *hw, u32 send_slope,
+ u32 idle_slope, u32 high_credit, u32 low_credit,
+ u32 queue);
/* Dump MAC registers */
void (*dump_regs)(struct mac_device_info *hw, u32 *reg_space);
/* Handle extra events on specific interrupts hw dependent */
#define MTL_OP_MODE_RTC_96 (2 << MTL_OP_MODE_RTC_SHIFT)
#define MTL_OP_MODE_RTC_128 (3 << MTL_OP_MODE_RTC_SHIFT)
+/* MTL ETS Control register */
+#define MTL_ETS_CTRL_BASE_ADDR 0x00000d10
+#define MTL_ETS_CTRL_BASE_OFFSET 0x40
+#define MTL_ETSX_CTRL_BASE_ADDR(x) (MTL_ETS_CTRL_BASE_ADDR + \
+ ((x) * MTL_ETS_CTRL_BASE_OFFSET))
+
+#define MTL_ETS_CTRL_CC BIT(3)
+#define MTL_ETS_CTRL_AVALG BIT(2)
+
/* MTL Queue Quantum Weight */
#define MTL_TXQ_WEIGHT_BASE_ADDR 0x00000d18
#define MTL_TXQ_WEIGHT_BASE_OFFSET 0x40
((x) * MTL_TXQ_WEIGHT_BASE_OFFSET))
#define MTL_TXQ_WEIGHT_ISCQW_MASK GENMASK(20, 0)
+/* MTL sendSlopeCredit register */
+#define MTL_SEND_SLP_CRED_BASE_ADDR 0x00000d1c
+#define MTL_SEND_SLP_CRED_OFFSET 0x40
+#define MTL_SEND_SLP_CREDX_BASE_ADDR(x) (MTL_SEND_SLP_CRED_BASE_ADDR + \
+ ((x) * MTL_SEND_SLP_CRED_OFFSET))
+
+#define MTL_SEND_SLP_CRED_SSC_MASK GENMASK(13, 0)
+
+/* MTL hiCredit register */
+#define MTL_HIGH_CRED_BASE_ADDR 0x00000d20
+#define MTL_HIGH_CRED_OFFSET 0x40
+#define MTL_HIGH_CREDX_BASE_ADDR(x) (MTL_HIGH_CRED_BASE_ADDR + \
+ ((x) * MTL_HIGH_CRED_OFFSET))
+
+#define MTL_HIGH_CRED_HC_MASK GENMASK(28, 0)
+
+/* MTL loCredit register */
+#define MTL_LOW_CRED_BASE_ADDR 0x00000d24
+#define MTL_LOW_CRED_OFFSET 0x40
+#define MTL_LOW_CREDX_BASE_ADDR(x) (MTL_LOW_CRED_BASE_ADDR + \
+ ((x) * MTL_LOW_CRED_OFFSET))
+
+#define MTL_HIGH_CRED_LC_MASK GENMASK(28, 0)
+
/* MTL debug */
#define MTL_DEBUG_TXSTSFSTS BIT(5)
#define MTL_DEBUG_TXFSTS BIT(4)
u32 value = readl(ioaddr + GMAC_RXQ_CTRL0);
value &= GMAC_RX_QUEUE_CLEAR(queue);
- if (mode == MTL_RX_AVB)
+ if (mode == MTL_QUEUE_AVB)
value |= GMAC_RX_AV_QUEUE_ENABLE(queue);
- else if (mode == MTL_RX_DCB)
+ else if (mode == MTL_QUEUE_DCB)
value |= GMAC_RX_DCB_QUEUE_ENABLE(queue);
writel(value, ioaddr + GMAC_RXQ_CTRL0);
writel(value, ioaddr + MTL_RXQ_DMA_MAP1);
}
+static void dwmac4_config_cbs(struct mac_device_info *hw,
+ u32 send_slope, u32 idle_slope,
+ u32 high_credit, u32 low_credit, u32 queue)
+{
+ void __iomem *ioaddr = hw->pcsr;
+ u32 value;
+
+ pr_debug("Queue %d configured as AVB. Parameters:\n", queue);
+ pr_debug("\tsend_slope: 0x%08x\n", send_slope);
+ pr_debug("\tidle_slope: 0x%08x\n", idle_slope);
+ pr_debug("\thigh_credit: 0x%08x\n", high_credit);
+ pr_debug("\tlow_credit: 0x%08x\n", low_credit);
+
+ /* enable AV algorithm */
+ value = readl(ioaddr + MTL_ETSX_CTRL_BASE_ADDR(queue));
+ value |= MTL_ETS_CTRL_AVALG;
+ value |= MTL_ETS_CTRL_CC;
+ writel(value, ioaddr + MTL_ETSX_CTRL_BASE_ADDR(queue));
+
+ /* configure send slope */
+ value = readl(ioaddr + MTL_SEND_SLP_CREDX_BASE_ADDR(queue));
+ value &= ~MTL_SEND_SLP_CRED_SSC_MASK;
+ value |= send_slope & MTL_SEND_SLP_CRED_SSC_MASK;
+ writel(value, ioaddr + MTL_SEND_SLP_CREDX_BASE_ADDR(queue));
+
+ /* configure idle slope (same register as tx weight) */
+ dwmac4_set_mtl_tx_queue_weight(hw, idle_slope, queue);
+
+ /* configure high credit */
+ value = readl(ioaddr + MTL_HIGH_CREDX_BASE_ADDR(queue));
+ value &= ~MTL_HIGH_CRED_HC_MASK;
+ value |= high_credit & MTL_HIGH_CRED_HC_MASK;
+ writel(value, ioaddr + MTL_HIGH_CREDX_BASE_ADDR(queue));
+
+ /* configure high credit */
+ value = readl(ioaddr + MTL_LOW_CREDX_BASE_ADDR(queue));
+ value &= ~MTL_HIGH_CRED_LC_MASK;
+ value |= low_credit & MTL_HIGH_CRED_LC_MASK;
+ writel(value, ioaddr + MTL_LOW_CREDX_BASE_ADDR(queue));
+}
+
static void dwmac4_dump_regs(struct mac_device_info *hw, u32 *reg_space)
{
void __iomem *ioaddr = hw->pcsr;
.prog_mtl_tx_algorithms = dwmac4_prog_mtl_tx_algorithms,
.set_mtl_tx_queue_weight = dwmac4_set_mtl_tx_queue_weight,
.map_mtl_to_dma = dwmac4_map_mtl_dma,
+ .config_cbs = dwmac4_config_cbs,
.dump_regs = dwmac4_dump_regs,
.host_irq_status = dwmac4_irq_status,
.host_mtl_irq_status = dwmac4_irq_mtl_status,
}
}
+/**
+ * stmmac_configure_cbs - Configure CBS in TX queue
+ * @priv: driver private structure
+ * Description: It is used for configuring CBS in AVB TX queues
+ */
+static void stmmac_configure_cbs(struct stmmac_priv *priv)
+{
+ u32 tx_queues_count = priv->plat->tx_queues_to_use;
+ u32 mode_to_use;
+ u32 queue;
+
+ for (queue = 0; queue < tx_queues_count; queue++) {
+ mode_to_use = priv->plat->tx_queues_cfg[queue].mode_to_use;
+ if (mode_to_use == MTL_QUEUE_DCB)
+ continue;
+
+ priv->hw->mac->config_cbs(priv->hw,
+ priv->plat->tx_queues_cfg[queue].send_slope,
+ priv->plat->tx_queues_cfg[queue].idle_slope,
+ priv->plat->tx_queues_cfg[queue].high_credit,
+ priv->plat->tx_queues_cfg[queue].low_credit,
+ queue);
+ }
+}
+
/**
* stmmac_rx_queue_dma_chan_map - Map RX queue to RX dma channel
* @priv: driver private structure
priv->hw->mac->prog_mtl_tx_algorithms(priv->hw,
priv->plat->tx_sched_algorithm);
+ /* Configure CBS in AVB TX queues */
+ if (tx_queues_count > 1 && priv->hw->mac->config_cbs)
+ stmmac_configure_cbs(priv);
+
/* Map RX MTL to DMA channels */
if (rx_queues_count > 1 && priv->hw->mac->map_mtl_to_dma)
stmmac_rx_queue_dma_chan_map(priv);
break;
if (of_property_read_bool(q_node, "snps,dcb-algorithm"))
- plat->rx_queues_cfg[queue].mode_to_use = MTL_RX_DCB;
+ plat->rx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB;
else if (of_property_read_bool(q_node, "snps,avb-algorithm"))
- plat->rx_queues_cfg[queue].mode_to_use = MTL_RX_AVB;
+ plat->rx_queues_cfg[queue].mode_to_use = MTL_QUEUE_AVB;
else
- plat->rx_queues_cfg[queue].mode_to_use = MTL_RX_DCB;
+ plat->rx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB;
if (of_property_read_u8(q_node, "snps,map-to-dma-channel",
&plat->rx_queues_cfg[queue].chan))
&plat->tx_queues_cfg[queue].weight))
plat->tx_queues_cfg[queue].weight = 0x10 + queue;
+ if (of_property_read_bool(q_node, "snps,dcb-algorithm")) {
+ plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB;
+ } else if (of_property_read_bool(q_node,
+ "snps,avb-algorithm")) {
+ plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_AVB;
+
+ /* Credit Base Shaper parameters used by AVB */
+ if (of_property_read_u32(q_node, "snps,send_slope",
+ &plat->tx_queues_cfg[queue].send_slope))
+ plat->tx_queues_cfg[queue].send_slope = 0x0;
+ if (of_property_read_u32(q_node, "snps,idle_slope",
+ &plat->tx_queues_cfg[queue].idle_slope))
+ plat->tx_queues_cfg[queue].idle_slope = 0x0;
+ if (of_property_read_u32(q_node, "snps,high_credit",
+ &plat->tx_queues_cfg[queue].high_credit))
+ plat->tx_queues_cfg[queue].high_credit = 0x0;
+ if (of_property_read_u32(q_node, "snps,low_credit",
+ &plat->tx_queues_cfg[queue].low_credit))
+ plat->tx_queues_cfg[queue].low_credit = 0x0;
+ } else {
+ plat->tx_queues_cfg[queue].mode_to_use = MTL_QUEUE_DCB;
+ }
+
queue++;
}
#define MTL_RX_ALGORITHM_SP 0x4
#define MTL_RX_ALGORITHM_WSP 0x5
-/* RX Queue Mode */
-#define MTL_RX_DCB 0x0
-#define MTL_RX_AVB 0x1
+/* RX/TX Queue Mode */
+#define MTL_QUEUE_DCB 0x0
+#define MTL_QUEUE_AVB 0x1
/* The MDC clock could be set higher than the IEEE 802.3
* specified frequency limit 0f 2.5 MHz, by programming a clock divider
struct stmmac_txq_cfg {
u8 weight;
+ u8 mode_to_use;
+ /* Credit Base Shaper parameters */
+ u32 send_slope;
+ u32 idle_slope;
+ u32 high_credit;
+ u32 low_credit;
};
struct plat_stmmacenet_data {