/*
- * Support for LGDT3302 & LGDT3303 (DViCO FusionHDTV Gold) - VSB/QAM
+ * Support for LGDT3302 and LGDT3303 - VSB/QAM
*
* Copyright (C) 2005 Wilson Michaels <wilsonmichaels@earthlink.net>
*
- * Based on code from Kirk Lapray <kirk_lapray@bigfoot.com>
- * Copyright (C) 2005
- *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
/*
* NOTES ABOUT THIS DRIVER
*
- * This driver supports DViCO FusionHDTV Gold under Linux.
+ * This Linux driver supports:
+ * DViCO FusionHDTV 3 Gold-Q
+ * DViCO FusionHDTV 3 Gold-T
+ * DViCO FusionHDTV 5 Gold
*
* TODO:
- * BER and signal strength always return 0.
- * Include support for LGDT3303
+ * signal strength always returns 0.
*
*/
#include <asm/byteorder.h>
#include "dvb_frontend.h"
-#include "dvb-pll.h"
#include "lgdt330x_priv.h"
#include "lgdt330x.h"
u32 current_frequency;
};
-static int i2c_writebytes (struct lgdt330x_state* state,
- u8 addr, /* demod_address or pll_address */
+static int i2c_write_demod_bytes (struct lgdt330x_state* state,
u8 *buf, /* data bytes to send */
int len /* number of bytes to send */ )
{
- u8 tmp[] = { buf[0], buf[1] };
struct i2c_msg msg =
- { .addr = addr, .flags = 0, .buf = tmp, .len = 2 };
- int err;
+ { .addr = state->config->demod_address,
+ .flags = 0,
+ .buf = buf,
+ .len = 2 };
int i;
+ int err;
- for (i=1; i<len; i++) {
- tmp[1] = buf[i];
+ for (i=0; i<len-1; i+=2){
if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) {
- printk(KERN_WARNING "lgdt330x: %s error (addr %02x <- %02x, err == %i)\n", __FUNCTION__, addr, buf[0], err);
+ printk(KERN_WARNING "lgdt330x: %s error (addr %02x <- %02x, err = %i)\n", __FUNCTION__, msg.buf[0], msg.buf[1], err);
if (err < 0)
return err;
else
return -EREMOTEIO;
}
- tmp[0]++;
- }
- return 0;
-}
-
-#if 0
-static int i2c_readbytes (struct lgdt330x_state* state,
- u8 addr, /* demod_address or pll_address */
- u8 *buf, /* holds data bytes read */
- int len /* number of bytes to read */ )
-{
- struct i2c_msg msg =
- { .addr = addr, .flags = I2C_M_RD, .buf = buf, .len = len };
- int err;
-
- if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) {
- printk(KERN_WARNING "lgdt330x: %s error (addr %02x, err == %i)\n", __FUNCTION__, addr, err);
- return -EREMOTEIO;
+ msg.buf += 2;
}
return 0;
}
-#endif
/*
* This routine writes the register (reg) to the demod bus
* then reads the data returned for (len) bytes.
*/
-static u8 i2c_selectreadbytes (struct lgdt330x_state* state,
+static u8 i2c_read_demod_bytes (struct lgdt330x_state* state,
enum I2C_REG reg, u8* buf, int len)
{
u8 wr [] = { reg };
}
/* Software reset */
-int lgdt330x_SwReset(struct lgdt330x_state* state)
+static int lgdt3302_SwReset(struct lgdt330x_state* state)
{
u8 ret;
u8 reset[] = {
* bits 5-0 are 1 to mask interrupts */
};
- ret = i2c_writebytes(state,
- state->config->demod_address,
+ ret = i2c_write_demod_bytes(state,
reset, sizeof(reset));
if (ret == 0) {
- /* spec says reset takes 100 ns why wait */
- /* mdelay(100); */ /* keep low for 100mS */
- reset[1] = 0x7f; /* force reset high (inactive)
- * and unmask interrupts */
- ret = i2c_writebytes(state,
- state->config->demod_address,
+
+ /* force reset high (inactive) and unmask interrupts */
+ reset[1] = 0x7f;
+ ret = i2c_write_demod_bytes(state,
reset, sizeof(reset));
}
- /* Spec does not indicate a need for this either */
- /*mdelay(5); */ /* wait 5 msec before doing more */
return ret;
}
+static int lgdt3303_SwReset(struct lgdt330x_state* state)
+{
+ u8 ret;
+ u8 reset[] = {
+ 0x02,
+ 0x00 /* bit 0 is active low software reset */
+ };
+
+ ret = i2c_write_demod_bytes(state,
+ reset, sizeof(reset));
+ if (ret == 0) {
+
+ /* force reset high (inactive) */
+ reset[1] = 0x01;
+ ret = i2c_write_demod_bytes(state,
+ reset, sizeof(reset));
+ }
+ return ret;
+}
+
+static int lgdt330x_SwReset(struct lgdt330x_state* state)
+{
+ switch (state->config->demod_chip) {
+ case LGDT3302:
+ return lgdt3302_SwReset(state);
+ case LGDT3303:
+ return lgdt3303_SwReset(state);
+ default:
+ return -ENODEV;
+ }
+}
+
+#ifdef MUTE_TDA9887
+static int i2c_write_ntsc_demod (struct lgdt330x_state* state, u8 buf[2])
+{
+ struct i2c_msg msg =
+ { .addr = 0x43,
+ .flags = 0,
+ .buf = buf,
+ .len = 2 };
+ int err;
+
+ if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) {
+ printk(KERN_WARNING "lgdt330x: %s error (addr %02x <- %02x, err = %i)\n", __FUNCTION__, msg.buf[0], msg.buf[1], err);
+ if (err < 0)
+ return err;
+ else
+ return -EREMOTEIO;
+ }
+ return 0;
+}
+
+static void fiddle_with_ntsc_if_demod(struct lgdt330x_state* state)
+{
+ // Experimental code
+ u8 buf0[] = {0x00, 0x20};
+ u8 buf1[] = {0x01, 0x00};
+ u8 buf2[] = {0x02, 0x00};
+
+ i2c_write_ntsc_demod(state, buf0);
+ i2c_write_ntsc_demod(state, buf1);
+ i2c_write_ntsc_demod(state, buf2);
+}
+#endif
+
static int lgdt330x_init(struct dvb_frontend* fe)
{
/* Hardware reset is done using gpio[0] of cx23880x chip.
* Maybe there needs to be a callable function in cx88-core or
* the caller of this function needs to do it. */
- dprintk("%s entered\n", __FUNCTION__);
- return lgdt330x_SwReset((struct lgdt330x_state*) fe->demodulator_priv);
+ /*
+ * Array of byte pairs <address, value>
+ * to initialize each different chip
+ */
+ static u8 lgdt3302_init_data[] = {
+ /* Use 50MHz parameter values from spec sheet since xtal is 50 */
+ /* Change the value of NCOCTFV[25:0] of carrier
+ recovery center frequency register */
+ VSB_CARRIER_FREQ0, 0x00,
+ VSB_CARRIER_FREQ1, 0x87,
+ VSB_CARRIER_FREQ2, 0x8e,
+ VSB_CARRIER_FREQ3, 0x01,
+ /* Change the TPCLK pin polarity
+ data is valid on falling clock */
+ DEMUX_CONTROL, 0xfb,
+ /* Change the value of IFBW[11:0] of
+ AGC IF/RF loop filter bandwidth register */
+ AGC_RF_BANDWIDTH0, 0x40,
+ AGC_RF_BANDWIDTH1, 0x93,
+ AGC_RF_BANDWIDTH2, 0x00,
+ /* Change the value of bit 6, 'nINAGCBY' and
+ 'NSSEL[1:0] of ACG function control register 2 */
+ AGC_FUNC_CTRL2, 0xc6,
+ /* Change the value of bit 6 'RFFIX'
+ of AGC function control register 3 */
+ AGC_FUNC_CTRL3, 0x40,
+ /* Set the value of 'INLVTHD' register 0x2a/0x2c
+ to 0x7fe */
+ AGC_DELAY0, 0x07,
+ AGC_DELAY2, 0xfe,
+ /* Change the value of IAGCBW[15:8]
+ of inner AGC loop filter bandwith */
+ AGC_LOOP_BANDWIDTH0, 0x08,
+ AGC_LOOP_BANDWIDTH1, 0x9a
+ };
+
+ static u8 lgdt3303_init_data[] = {
+ 0x4c, 0x14
+ };
+
+ struct lgdt330x_state* state = fe->demodulator_priv;
+ char *chip_name;
+ int err;
+
+ switch (state->config->demod_chip) {
+ case LGDT3302:
+ chip_name = "LGDT3302";
+ err = i2c_write_demod_bytes(state, lgdt3302_init_data,
+ sizeof(lgdt3302_init_data));
+ break;
+ case LGDT3303:
+ chip_name = "LGDT3303";
+ err = i2c_write_demod_bytes(state, lgdt3303_init_data,
+ sizeof(lgdt3303_init_data));
+#ifdef MUTE_TDA9887
+ fiddle_with_ntsc_if_demod(state);
+#endif
+ break;
+ default:
+ chip_name = "undefined";
+ printk (KERN_WARNING "Only LGDT3302 and LGDT3303 are supported chips.\n");
+ err = -ENODEV;
+ }
+ dprintk("%s entered as %s\n", __FUNCTION__, chip_name);
+ if (err < 0)
+ return err;
+ return lgdt330x_SwReset(state);
}
static int lgdt330x_read_ber(struct dvb_frontend* fe, u32* ber)
{
- *ber = 0; /* Dummy out for now */
+ *ber = 0; /* Not supplied by the demod chips */
return 0;
}
static int lgdt330x_read_ucblocks(struct dvb_frontend* fe, u32* ucblocks)
{
- struct lgdt330x_state* state = (struct lgdt330x_state*) fe->demodulator_priv;
+ struct lgdt330x_state* state = fe->demodulator_priv;
+ int err;
u8 buf[2];
- i2c_selectreadbytes(state, PACKET_ERR_COUNTER1, buf, sizeof(buf));
+ switch (state->config->demod_chip) {
+ case LGDT3302:
+ err = i2c_read_demod_bytes(state, LGDT3302_PACKET_ERR_COUNTER1,
+ buf, sizeof(buf));
+ break;
+ case LGDT3303:
+ err = i2c_read_demod_bytes(state, LGDT3303_PACKET_ERR_COUNTER1,
+ buf, sizeof(buf));
+ break;
+ default:
+ printk(KERN_WARNING
+ "Only LGDT3302 and LGDT3303 are supported chips.\n");
+ err = -ENODEV;
+ }
*ucblocks = (buf[0] << 8) | buf[1];
return 0;
static int lgdt330x_set_parameters(struct dvb_frontend* fe,
struct dvb_frontend_parameters *param)
{
- struct lgdt330x_state* state =
- (struct lgdt330x_state*) fe->demodulator_priv;
+ /*
+ * Array of byte pairs <address, value>
+ * to initialize 8VSB for lgdt3303 chip 50 MHz IF
+ */
+ static u8 lgdt3303_8vsb_44_data[] = {
+ 0x04, 0x00,
+ 0x0d, 0x40,
+ 0x0e, 0x87,
+ 0x0f, 0x8e,
+ 0x10, 0x01,
+ 0x47, 0x8b };
+
+ /*
+ * Array of byte pairs <address, value>
+ * to initialize QAM for lgdt3303 chip
+ */
+ static u8 lgdt3303_qam_data[] = {
+ 0x04, 0x00,
+ 0x0d, 0x00,
+ 0x0e, 0x00,
+ 0x0f, 0x00,
+ 0x10, 0x00,
+ 0x51, 0x63,
+ 0x47, 0x66,
+ 0x48, 0x66,
+ 0x4d, 0x1a,
+ 0x49, 0x08,
+ 0x4a, 0x9b };
+
+ struct lgdt330x_state* state = fe->demodulator_priv;
- /* Use 50MHz parameter values from spec sheet since xtal is 50 */
static u8 top_ctrl_cfg[] = { TOP_CONTROL, 0x03 };
- static u8 vsb_freq_cfg[] = { VSB_CARRIER_FREQ0, 0x00, 0x87, 0x8e, 0x01 };
- static u8 demux_ctrl_cfg[] = { DEMUX_CONTROL, 0xfb };
- static u8 agc_rf_cfg[] = { AGC_RF_BANDWIDTH0, 0x40, 0x93, 0x00 };
- static u8 agc_ctrl_cfg[] = { AGC_FUNC_CTRL2, 0xc6, 0x40 };
- static u8 agc_delay_cfg[] = { AGC_DELAY0, 0x07, 0x00, 0xfe };
- static u8 agc_loop_cfg[] = { AGC_LOOP_BANDWIDTH0, 0x08, 0x9a };
+ int err;
/* Change only if we are actually changing the modulation */
if (state->current_modulation != param->u.vsb.modulation) {
switch(param->u.vsb.modulation) {
case VSB_8:
dprintk("%s: VSB_8 MODE\n", __FUNCTION__);
- /* Select VSB mode and serial MPEG interface */
- top_ctrl_cfg[1] = 0x07;
+ /* Select VSB mode */
+ top_ctrl_cfg[1] = 0x03;
/* Select ANT connector if supported by card */
if (state->config->pll_rf_set)
state->config->pll_rf_set(fe, 1);
+
+ if (state->config->demod_chip == LGDT3303) {
+ err = i2c_write_demod_bytes(state, lgdt3303_8vsb_44_data,
+ sizeof(lgdt3303_8vsb_44_data));
+ }
break;
case QAM_64:
dprintk("%s: QAM_64 MODE\n", __FUNCTION__);
- /* Select QAM_64 mode and serial MPEG interface */
- top_ctrl_cfg[1] = 0x04;
+ /* Select QAM_64 mode */
+ top_ctrl_cfg[1] = 0x00;
/* Select CABLE connector if supported by card */
if (state->config->pll_rf_set)
state->config->pll_rf_set(fe, 0);
+
+ if (state->config->demod_chip == LGDT3303) {
+ err = i2c_write_demod_bytes(state, lgdt3303_qam_data,
+ sizeof(lgdt3303_qam_data));
+ }
break;
case QAM_256:
dprintk("%s: QAM_256 MODE\n", __FUNCTION__);
- /* Select QAM_256 mode and serial MPEG interface */
- top_ctrl_cfg[1] = 0x05;
+ /* Select QAM_256 mode */
+ top_ctrl_cfg[1] = 0x01;
/* Select CABLE connector if supported by card */
if (state->config->pll_rf_set)
state->config->pll_rf_set(fe, 0);
+
+ if (state->config->demod_chip == LGDT3303) {
+ err = i2c_write_demod_bytes(state, lgdt3303_qam_data,
+ sizeof(lgdt3303_qam_data));
+ }
break;
default:
printk(KERN_WARNING "lgdt330x: %s: Modulation type(%d) UNSUPPORTED\n", __FUNCTION__, param->u.vsb.modulation);
return -1;
}
- /* Initializations common to all modes */
+ /*
+ * select serial or parallel MPEG harware interface
+ * Serial: 0x04 for LGDT3302 or 0x40 for LGDT3303
+ * Parallel: 0x00
+ */
+ top_ctrl_cfg[1] |= state->config->serial_mpeg;
/* Select the requested mode */
- i2c_writebytes(state, state->config->demod_address,
- top_ctrl_cfg, sizeof(top_ctrl_cfg));
-
- /* Change the value of IFBW[11:0]
- of AGC IF/RF loop filter bandwidth register */
- i2c_writebytes(state, state->config->demod_address,
- agc_rf_cfg, sizeof(agc_rf_cfg));
-
- /* Change the value of bit 6, 'nINAGCBY' and
- 'NSSEL[1:0] of ACG function control register 2 */
- /* Change the value of bit 6 'RFFIX'
- of AGC function control register 3 */
- i2c_writebytes(state, state->config->demod_address,
- agc_ctrl_cfg, sizeof(agc_ctrl_cfg));
-
- /* Change the TPCLK pin polarity
- data is valid on falling clock */
- i2c_writebytes(state, state->config->demod_address,
- demux_ctrl_cfg, sizeof(demux_ctrl_cfg));
-
- /* Change the value of NCOCTFV[25:0] of carrier
- recovery center frequency register */
- i2c_writebytes(state, state->config->demod_address,
- vsb_freq_cfg, sizeof(vsb_freq_cfg));
-
- /* Set the value of 'INLVTHD' register 0x2a/0x2c to 0x7fe */
- i2c_writebytes(state, state->config->demod_address,
- agc_delay_cfg, sizeof(agc_delay_cfg));
-
- /* Change the value of IAGCBW[15:8]
- of inner AGC loop filter bandwith */
- i2c_writebytes(state, state->config->demod_address,
- agc_loop_cfg, sizeof(agc_loop_cfg));
-
+ i2c_write_demod_bytes(state, top_ctrl_cfg,
+ sizeof(top_ctrl_cfg));
state->config->set_ts_params(fe, 0);
state->current_modulation = param->u.vsb.modulation;
}
/* Change only if we are actually changing the channel */
if (state->current_frequency != param->frequency) {
- u8 buf[5];
- struct i2c_msg msg = { .flags = 0, .buf = &buf[1], .len = 4 };
- int err;
-
- state->config->pll_set(fe, param, buf);
- msg.addr = buf[0];
-
- dprintk("%s: tuner at 0x%02x bytes: 0x%02x 0x%02x "
- "0x%02x 0x%02x\n", __FUNCTION__,
- buf[0],buf[1],buf[2],buf[3],buf[4]);
- if ((err = i2c_transfer(state->i2c, &msg, 1)) != 1) {
- printk(KERN_WARNING "lgdt330x: %s error (addr %02x <- %02x, err = %i)\n", __FUNCTION__, buf[0], buf[1], err);
- if (err < 0)
- return err;
- else
- return -EREMOTEIO;
- }
-#if 0
- /* Check the status of the tuner pll */
- i2c_readbytes(state, buf[0], &buf[1], 1);
- dprintk("%s: tuner status byte = 0x%02x\n", __FUNCTION__, buf[1]);
-#endif
- /* Update current frequency */
+ /* Tune to the new frequency */
+ state->config->pll_set(fe, param);
+ /* Keep track of the new frequency */
state->current_frequency = param->frequency;
}
lgdt330x_SwReset(state);
return 0;
}
-static int lgdt330x_read_status(struct dvb_frontend* fe, fe_status_t* status)
+static int lgdt3302_read_status(struct dvb_frontend* fe, fe_status_t* status)
{
- struct lgdt330x_state* state = (struct lgdt330x_state*) fe->demodulator_priv;
+ struct lgdt330x_state* state = fe->demodulator_priv;
u8 buf[3];
*status = 0; /* Reset status result */
- /*
- * You must set the Mask bits to 1 in the IRQ_MASK in order
- * to see that status bit in the IRQ_STATUS register.
- * This is done in SwReset();
- */
-
/* AGC status register */
- i2c_selectreadbytes(state, AGC_STATUS, buf, 1);
+ i2c_read_demod_bytes(state, AGC_STATUS, buf, 1);
dprintk("%s: AGC_STATUS = 0x%02x\n", __FUNCTION__, buf[0]);
if ((buf[0] & 0x0c) == 0x8){
/* Test signal does not exist flag */
return 0;
}
+ /*
+ * You must set the Mask bits to 1 in the IRQ_MASK in order
+ * to see that status bit in the IRQ_STATUS register.
+ * This is done in SwReset();
+ */
/* signal status */
- i2c_selectreadbytes(state, TOP_CONTROL, buf, sizeof(buf));
+ i2c_read_demod_bytes(state, TOP_CONTROL, buf, sizeof(buf));
dprintk("%s: TOP_CONTROL = 0x%02x, IRO_MASK = 0x%02x, IRQ_STATUS = 0x%02x\n", __FUNCTION__, buf[0], buf[1], buf[2]);
-#if 0
- /* Alternative method to check for a signal */
- /* using the SNR good/bad interrupts. */
- if ((buf[2] & 0x30) == 0x10)
- *status |= FE_HAS_SIGNAL;
-#endif
/* sync status */
if ((buf[2] & 0x03) == 0x01) {
}
/* Carrier Recovery Lock Status Register */
- i2c_selectreadbytes(state, CARRIER_LOCK, buf, 1);
+ i2c_read_demod_bytes(state, CARRIER_LOCK, buf, 1);
dprintk("%s: CARRIER_LOCK = 0x%02x\n", __FUNCTION__, buf[0]);
switch (state->current_modulation) {
case QAM_256:
return 0;
}
+static int lgdt3303_read_status(struct dvb_frontend* fe, fe_status_t* status)
+{
+ struct lgdt330x_state* state = fe->demodulator_priv;
+ int err;
+ u8 buf[3];
+
+ *status = 0; /* Reset status result */
+
+ /* lgdt3303 AGC status register */
+ err = i2c_read_demod_bytes(state, 0x58, buf, 1);
+ if (err < 0)
+ return err;
+
+ dprintk("%s: AGC_STATUS = 0x%02x\n", __FUNCTION__, buf[0]);
+ if ((buf[0] & 0x21) == 0x01){
+ /* Test input signal does not exist flag */
+ /* as well as the AGC lock flag. */
+ *status |= FE_HAS_SIGNAL;
+ } else {
+ /* Without a signal all other status bits are meaningless */
+ return 0;
+ }
+
+ /* Carrier Recovery Lock Status Register */
+ i2c_read_demod_bytes(state, CARRIER_LOCK, buf, 1);
+ dprintk("%s: CARRIER_LOCK = 0x%02x\n", __FUNCTION__, buf[0]);
+ switch (state->current_modulation) {
+ case QAM_256:
+ case QAM_64:
+ /* Need to undestand why there are 3 lock levels here */
+ if ((buf[0] & 0x07) == 0x07)
+ *status |= FE_HAS_CARRIER;
+ else
+ break;
+ i2c_read_demod_bytes(state, 0x8a, buf, 1);
+ if ((buf[0] & 0x04) == 0x04)
+ *status |= FE_HAS_SYNC;
+ if ((buf[0] & 0x01) == 0x01)
+ *status |= FE_HAS_LOCK;
+ if ((buf[0] & 0x08) == 0x08)
+ *status |= FE_HAS_VITERBI;
+ break;
+ case VSB_8:
+ if ((buf[0] & 0x80) == 0x80)
+ *status |= FE_HAS_CARRIER;
+ else
+ break;
+ i2c_read_demod_bytes(state, 0x38, buf, 1);
+ if ((buf[0] & 0x02) == 0x00)
+ *status |= FE_HAS_SYNC;
+ if ((buf[0] & 0x01) == 0x01) {
+ *status |= FE_HAS_LOCK;
+ *status |= FE_HAS_VITERBI;
+ }
+ break;
+ default:
+ printk("KERN_WARNING lgdt330x: %s: Modulation set to unsupported value\n", __FUNCTION__);
+ }
+ return 0;
+}
+
static int lgdt330x_read_signal_strength(struct dvb_frontend* fe, u16* strength)
{
/* not directly available. */
+ *strength = 0;
return 0;
}
-static int lgdt330x_read_snr(struct dvb_frontend* fe, u16* snr)
+static int lgdt3302_read_snr(struct dvb_frontend* fe, u16* snr)
{
#ifdef SNR_IN_DB
/*
91, 115, 144, 182, 229, 288, 362, 456, 574, 722,
909, 1144, 1440, 1813, 2282, 2873, 3617, 4553, 5732, 7216,
9084, 11436, 14396, 18124, 22817, 28724, 36161, 45524, 57312, 72151,
- 90833, 114351, 143960, 181235, 228161, 0x040000
+ 90833, 114351, 143960, 181235, 228161, 0x080000
};
static u8 buf[5];/* read data buffer */
static u32 snr_db; /* index into SNR_EQ[] */
struct lgdt330x_state* state = (struct lgdt330x_state*) fe->demodulator_priv;
- /* read both equalizer and pase tracker noise data */
- i2c_selectreadbytes(state, EQPH_ERR0, buf, sizeof(buf));
+ /* read both equalizer and phase tracker noise data */
+ i2c_read_demod_bytes(state, EQPH_ERR0, buf, sizeof(buf));
if (state->current_modulation == VSB_8) {
/* Equalizer Mean-Square Error Register for VSB */
struct lgdt330x_state* state = (struct lgdt330x_state*) fe->demodulator_priv;
/* read both equalizer and pase tracker noise data */
- i2c_selectreadbytes(state, EQPH_ERR0, buf, sizeof(buf));
+ i2c_read_demod_bytes(state, EQPH_ERR0, buf, sizeof(buf));
if (state->current_modulation == VSB_8) {
- /* Equalizer Mean-Square Error Register for VSB */
- noise = ((buf[0] & 7) << 16) | (buf[1] << 8) | buf[2];
- } else {
- /* Phase Tracker Mean-Square Error Register for QAM */
+ /* Phase Tracker Mean-Square Error Register for VSB */
noise = ((buf[0] & 7<<3) << 13) | (buf[3] << 8) | buf[4];
+ } else {
+
+ /* Carrier Recovery Mean-Square Error for QAM */
+ i2c_read_demod_bytes(state, 0x1a, buf, 2);
+ noise = ((buf[0] & 3) << 8) | buf[1];
}
/* Small values for noise mean signal is better so invert noise */
- /* Noise is 19 bit value so discard 3 LSB*/
- *snr = ~noise>>3;
+ *snr = ~noise;
#endif
dprintk("%s: noise = 0x%05x, snr = %idb\n",__FUNCTION__, noise, *snr);
return 0;
}
+static int lgdt3303_read_snr(struct dvb_frontend* fe, u16* snr)
+{
+ /* Return the raw noise value */
+ static u8 buf[5];/* read data buffer */
+ static u32 noise; /* noise value */
+ struct lgdt330x_state* state = (struct lgdt330x_state*) fe->demodulator_priv;
+
+ if (state->current_modulation == VSB_8) {
+
+ /* Phase Tracker Mean-Square Error Register for VSB */
+ noise = ((buf[0] & 7) << 16) | (buf[3] << 8) | buf[4];
+ } else {
+
+ /* Carrier Recovery Mean-Square Error for QAM */
+ i2c_read_demod_bytes(state, 0x1a, buf, 2);
+ noise = (buf[0] << 8) | buf[1];
+ }
+
+ /* Small values for noise mean signal is better so invert noise */
+ *snr = ~noise;
+
+ dprintk("%s: noise = 0x%05x, snr = %idb\n",__FUNCTION__, noise, *snr);
+
+ return 0;
+}
+
static int lgdt330x_get_tune_settings(struct dvb_frontend* fe, struct dvb_frontend_tune_settings* fe_tune_settings)
{
/* I have no idea about this - it may not be needed */
kfree(state);
}
-static struct dvb_frontend_ops lgdt330x_ops;
+static struct dvb_frontend_ops lgdt3302_ops;
+static struct dvb_frontend_ops lgdt3303_ops;
struct dvb_frontend* lgdt330x_attach(const struct lgdt330x_config* config,
struct i2c_adapter* i2c)
/* Setup the state */
state->config = config;
state->i2c = i2c;
- memcpy(&state->ops, &lgdt330x_ops, sizeof(struct dvb_frontend_ops));
+ switch (config->demod_chip) {
+ case LGDT3302:
+ memcpy(&state->ops, &lgdt3302_ops, sizeof(struct dvb_frontend_ops));
+ break;
+ case LGDT3303:
+ memcpy(&state->ops, &lgdt3303_ops, sizeof(struct dvb_frontend_ops));
+ break;
+ default:
+ goto error;
+ }
+
/* Verify communication with demod chip */
- if (i2c_selectreadbytes(state, 2, buf, 1))
+ if (i2c_read_demod_bytes(state, 2, buf, 1))
goto error;
state->current_frequency = -1;
return NULL;
}
-static struct dvb_frontend_ops lgdt330x_ops = {
+static struct dvb_frontend_ops lgdt3302_ops = {
+ .info = {
+ .name= "LG Electronics LGDT3302/LGDT3303 VSB/QAM Frontend",
+ .type = FE_ATSC,
+ .frequency_min= 54000000,
+ .frequency_max= 858000000,
+ .frequency_stepsize= 62500,
+ /* Symbol rate is for all VSB modes need to check QAM */
+ .symbol_rate_min = 10762000,
+ .symbol_rate_max = 10762000,
+ .caps = FE_CAN_QAM_64 | FE_CAN_QAM_256 | FE_CAN_8VSB
+ },
+ .init = lgdt330x_init,
+ .set_frontend = lgdt330x_set_parameters,
+ .get_frontend = lgdt330x_get_frontend,
+ .get_tune_settings = lgdt330x_get_tune_settings,
+ .read_status = lgdt3302_read_status,
+ .read_ber = lgdt330x_read_ber,
+ .read_signal_strength = lgdt330x_read_signal_strength,
+ .read_snr = lgdt3302_read_snr,
+ .read_ucblocks = lgdt330x_read_ucblocks,
+ .release = lgdt330x_release,
+};
+
+static struct dvb_frontend_ops lgdt3303_ops = {
.info = {
- .name= "LG Electronics lgdt330x VSB/QAM Frontend",
+ .name= "LG Electronics LGDT3303 VSB/QAM Frontend",
.type = FE_ATSC,
.frequency_min= 54000000,
.frequency_max= 858000000,
.set_frontend = lgdt330x_set_parameters,
.get_frontend = lgdt330x_get_frontend,
.get_tune_settings = lgdt330x_get_tune_settings,
- .read_status = lgdt330x_read_status,
+ .read_status = lgdt3303_read_status,
.read_ber = lgdt330x_read_ber,
.read_signal_strength = lgdt330x_read_signal_strength,
- .read_snr = lgdt330x_read_snr,
+ .read_snr = lgdt3303_read_snr,
.read_ucblocks = lgdt330x_read_ucblocks,
.release = lgdt330x_release,
};
-MODULE_DESCRIPTION("lgdt330x [DViCO FusionHDTV 3 Gold] (ATSC 8VSB & ITU-T J.83 AnnexB 64/256 QAM) Demodulator Driver");
+MODULE_DESCRIPTION("LGDT330X (ATSC 8VSB & ITU-T J.83 AnnexB 64/256 QAM) Demodulator Driver");
MODULE_AUTHOR("Wilson Michaels");
MODULE_LICENSE("GPL");
/*
* Local variables:
* c-basic-offset: 8
- * compile-command: "make DVB=1"
* End:
*/
projects / GitHub / MotorolaMobilityLLC / kernel-slsi.git / commitdiff