#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */
#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5Ghz channel */
#define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */
+/* TSSI information */
+#define B43_SHM_SH_TSSI_CCK 0x0058 /* TSSI for last 4 CCK frames (32bit) */
+#define B43_SHM_SH_TSSI_OFDM_A 0x0068 /* TSSI for last 4 OFDM frames (32bit) */
+#define B43_SHM_SH_TSSI_OFDM_G 0x0070 /* TSSI for last 4 OFDM frames (32bit) */
+#define B43_TSSI_MAX 0x7F /* Max value for one TSSI value */
/* SHM_SHARED TX FIFO variables */
#define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */
#define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */
struct b43_qos_params qos_params[4];
/* Workqueue for updating QOS parameters in hardware. */
struct work_struct qos_update_work;
+
+ /* Work for adjustment of the transmission power.
+ * This is scheduled when we determine that the actual TX output
+ * power doesn't match what we want. */
+ struct work_struct txpower_adjust_work;
};
/* In-memory representation of a cached microcode file. */
if (ops->pwork_60sec)
ops->pwork_60sec(dev);
+
+ /* Force check the TX power emission now. */
+ b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME);
}
static void b43_periodic_every30sec(struct b43_wldev *dev)
if (phy->ops->pwork_15sec)
phy->ops->pwork_15sec(dev);
- phy->ops->xmitpower(dev);
-
atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT);
wmb();
}
/* Adjust the desired TX power level. */
if (conf->power_level != 0) {
- if (conf->power_level != phy->power_level) {
- phy->power_level = conf->power_level;
- phy->ops->xmitpower(dev);
+ spin_lock_irqsave(&wl->irq_lock, flags);
+ if (conf->power_level != phy->desired_txpower) {
+ phy->desired_txpower = conf->power_level;
+ b43_phy_txpower_check(dev, B43_TXPWR_IGNORE_TIME |
+ B43_TXPWR_IGNORE_TSSI);
}
+ spin_unlock_irqrestore(&wl->irq_lock, flags);
}
/* Antennas for RX and management frame TX. */
struct b43_phy *phy)
{
phy->hardware_power_control = !!modparam_hwpctl;
+ phy->next_txpwr_check_time = jiffies;
/* PHY TX errors counter. */
atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT);
}
b43_wireless_core_stop(dev);
b43_wireless_core_exit(dev);
mutex_unlock(&wl->mutex);
+
+ cancel_work_sync(&(wl->txpower_adjust_work));
}
static int b43_op_set_retry_limit(struct ieee80211_hw *hw,
INIT_LIST_HEAD(&wl->devlist);
INIT_WORK(&wl->qos_update_work, b43_qos_update_work);
INIT_WORK(&wl->beacon_update_trigger, b43_beacon_update_trigger_work);
+ INIT_WORK(&wl->txpower_adjust_work, b43_phy_txpower_adjust_work);
ssb_set_devtypedata(dev, wl);
b43info(wl, "Broadcom %04X WLAN found\n", dev->bus->chip_id);
{//TODO
}
-void b43_nphy_xmitpower(struct b43_wldev *dev)
+static void b43_nphy_op_adjust_txpower(struct b43_wldev *dev)
{//TODO
}
+static enum b43_txpwr_result b43_nphy_op_recalc_txpower(struct b43_wldev *dev,
+ bool ignore_tssi)
+{//TODO
+ return B43_TXPWR_RES_DONE;
+}
+
static void b43_chantab_radio_upload(struct b43_wldev *dev,
const struct b43_nphy_channeltab_entry *e)
{
return 36;
}
-static void b43_nphy_op_xmitpower(struct b43_wldev *dev)
-{//TODO
-}
-
const struct b43_phy_operations b43_phyops_n = {
.allocate = b43_nphy_op_allocate,
.init = b43_nphy_op_init,
.software_rfkill = b43_nphy_op_software_rfkill,
.switch_channel = b43_nphy_op_switch_channel,
.get_default_chan = b43_nphy_op_get_default_chan,
- .xmitpower = b43_nphy_op_xmitpower,
+ .recalc_txpower = b43_nphy_op_recalc_txpower,
+ .adjust_txpower = b43_nphy_op_adjust_txpower,
};
b43_hf_write(dev, hf);
}
-static void b43_aphy_op_xmitpower(struct b43_wldev *dev)
+static void b43_aphy_op_adjust_txpower(struct b43_wldev *dev)
{//TODO
}
+static enum b43_txpwr_result b43_aphy_op_recalc_txpower(struct b43_wldev *dev,
+ bool ignore_tssi)
+{//TODO
+ return B43_TXPWR_RES_DONE;
+}
+
static void b43_aphy_op_pwork_15sec(struct b43_wldev *dev)
{//TODO
}
.switch_channel = b43_aphy_op_switch_channel,
.get_default_chan = b43_aphy_op_get_default_chan,
.set_rx_antenna = b43_aphy_op_set_rx_antenna,
- .xmitpower = b43_aphy_op_xmitpower,
+ .recalc_txpower = b43_aphy_op_recalc_txpower,
+ .adjust_txpower = b43_aphy_op_adjust_txpower,
.pwork_15sec = b43_aphy_op_pwork_15sec,
.pwork_60sec = b43_aphy_op_pwork_60sec,
};
phy->ops->software_rfkill(dev, state);
phy->radio_on = (state == RFKILL_STATE_UNBLOCKED);
}
+
+/**
+ * b43_phy_txpower_adjust_work - TX power workqueue.
+ *
+ * Workqueue for updating the TX power parameters in hardware.
+ */
+void b43_phy_txpower_adjust_work(struct work_struct *work)
+{
+ struct b43_wl *wl = container_of(work, struct b43_wl,
+ txpower_adjust_work);
+ struct b43_wldev *dev;
+
+ mutex_lock(&wl->mutex);
+ dev = wl->current_dev;
+
+ if (likely(dev && (b43_status(dev) >= B43_STAT_STARTED)))
+ dev->phy.ops->adjust_txpower(dev);
+
+ mutex_unlock(&wl->mutex);
+}
+
+/* Called with wl->irq_lock locked */
+void b43_phy_txpower_check(struct b43_wldev *dev, unsigned int flags)
+{
+ struct b43_phy *phy = &dev->phy;
+ unsigned long now = jiffies;
+ enum b43_txpwr_result result;
+
+ if (!(flags & B43_TXPWR_IGNORE_TIME)) {
+ /* Check if it's time for a TXpower check. */
+ if (time_before(now, phy->next_txpwr_check_time))
+ return; /* Not yet */
+ }
+ /* The next check will be needed in two seconds, or later. */
+ phy->next_txpwr_check_time = round_jiffies(now + (HZ * 2));
+
+ if ((dev->dev->bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
+ (dev->dev->bus->boardinfo.type == SSB_BOARD_BU4306))
+ return; /* No software txpower adjustment needed */
+
+ result = phy->ops->recalc_txpower(dev, !!(flags & B43_TXPWR_IGNORE_TSSI));
+ if (result == B43_TXPWR_RES_DONE)
+ return; /* We are done. */
+ B43_WARN_ON(result != B43_TXPWR_RES_NEED_ADJUST);
+ B43_WARN_ON(phy->ops->adjust_txpower == NULL);
+
+ /* We must adjust the transmission power in hardware.
+ * Schedule b43_phy_txpower_adjust_work(). */
+ queue_work(dev->wl->hw->workqueue, &dev->wl->txpower_adjust_work);
+}
+
+int b43_phy_shm_tssi_read(struct b43_wldev *dev, u16 shm_offset)
+{
+ const bool is_ofdm = (shm_offset != B43_SHM_SH_TSSI_CCK);
+ unsigned int a, b, c, d;
+ unsigned int average;
+ u32 tmp;
+
+ tmp = b43_shm_read32(dev, B43_SHM_SHARED, shm_offset);
+ a = tmp & 0xFF;
+ b = (tmp >> 8) & 0xFF;
+ c = (tmp >> 16) & 0xFF;
+ d = (tmp >> 24) & 0xFF;
+ if (a == 0 || a == B43_TSSI_MAX ||
+ b == 0 || b == B43_TSSI_MAX ||
+ c == 0 || c == B43_TSSI_MAX ||
+ d == 0 || d == B43_TSSI_MAX)
+ return -ENOENT;
+ /* The values are OK. Clear them. */
+ tmp = B43_TSSI_MAX | (B43_TSSI_MAX << 8) |
+ (B43_TSSI_MAX << 16) | (B43_TSSI_MAX << 24);
+ b43_shm_write32(dev, B43_SHM_SHARED, shm_offset, tmp);
+
+ if (is_ofdm) {
+ a = (a + 32) & 0x3F;
+ b = (b + 32) & 0x3F;
+ c = (c + 32) & 0x3F;
+ d = (d + 32) & 0x3F;
+ }
+
+ /* Get the average of the values with 0.5 added to each value. */
+ average = (a + b + c + d + 2) / 4;
+ if (is_ofdm) {
+ /* Adjust for CCK-boost */
+ if (b43_shm_read16(dev, B43_SHM_SHARED, B43_SHM_SH_HOSTFLO)
+ & B43_HF_CCKBOOST)
+ average = (average >= 13) ? (average - 13) : 0;
+ }
+
+ return average;
+}
B43_ANTENNA_DEFAULT = B43_ANTENNA_AUTO,
};
+/**
+ * enum b43_txpwr_result - Return value for the recalc_txpower PHY op.
+ *
+ * @B43_TXPWR_RES_NEED_ADJUST: Values changed. Hardware adjustment is needed.
+ * @B43_TXPWR_RES_DONE: No more work to do. Everything is done.
+ */
+enum b43_txpwr_result {
+ B43_TXPWR_RES_NEED_ADJUST,
+ B43_TXPWR_RES_DONE,
+};
+
/**
* struct b43_phy_operations - Function pointers for PHY ops.
*
* @interf_mitigation: Switch the Interference Mitigation mode.
* Can be NULL, if not supported.
*
- * @xmitpower: FIXME REMOVEME
+ * @recalc_txpower: Recalculate the transmission power parameters.
+ * This callback has to recalculate the TX power settings,
+ * but does not need to write them to the hardware, yet.
+ * Returns enum b43_txpwr_result to indicate whether the hardware
+ * needs to be adjusted.
+ * If B43_TXPWR_NEED_ADJUST is returned, @adjust_txpower
+ * will be called later.
+ * If the parameter "ignore_tssi" is true, the TSSI values should
+ * be ignored and a recalculation of the power settings should be
+ * done even if the TSSI values did not change.
+ * This callback is called with wl->irq_lock held and must not sleep.
* Must not be NULL.
+ * @adjust_txpower: Write the previously calculated TX power settings
+ * (from @recalc_txpower) to the hardware.
+ * This function may sleep.
+ * Can be NULL, if (and ONLY if) @recalc_txpower _always_
+ * returns B43_TXPWR_RES_DONE.
*
* @pwork_15sec: Periodic work. Called every 15 seconds.
* Can be NULL, if not required.
enum b43_interference_mitigation new_mode);
/* Transmission power adjustment */
- void (*xmitpower)(struct b43_wldev *dev);
+ enum b43_txpwr_result (*recalc_txpower)(struct b43_wldev *dev,
+ bool ignore_tssi);
+ void (*adjust_txpower)(struct b43_wldev *dev);
/* Misc */
void (*pwork_15sec)(struct b43_wldev *dev);
/* Desired TX power level (in dBm).
* This is set by the user and adjusted in b43_phy_xmitpower(). */
- u8 power_level;
+ int desired_txpower;
/* Hardware Power Control enabled? */
bool hardware_power_control;
+ /* The time (in absolute jiffies) when the next TX power output
+ * check is needed. */
+ unsigned long next_txpwr_check_time;
+
/* current channel */
unsigned int channel;
*/
void b43_software_rfkill(struct b43_wldev *dev, enum rfkill_state state);
+/**
+ * b43_phy_txpower_check - Check TX power output.
+ *
+ * Compare the current TX power output to the desired power emission
+ * and schedule an adjustment in case it mismatches.
+ * Requires wl->irq_lock locked.
+ *
+ * @flags: OR'ed enum b43_phy_txpower_check_flags flags.
+ * See the docs below.
+ */
+void b43_phy_txpower_check(struct b43_wldev *dev, unsigned int flags);
+/**
+ * enum b43_phy_txpower_check_flags - Flags for b43_phy_txpower_check()
+ *
+ * @B43_TXPWR_IGNORE_TIME: Ignore the schedule time and force-redo
+ * the check now.
+ * @B43_TXPWR_IGNORE_TSSI: Redo the recalculation, even if the average
+ * TSSI did not change.
+ */
+enum b43_phy_txpower_check_flags {
+ B43_TXPWR_IGNORE_TIME = (1 << 0),
+ B43_TXPWR_IGNORE_TSSI = (1 << 1),
+};
+
+struct work_struct;
+void b43_phy_txpower_adjust_work(struct work_struct *work);
+
+/**
+ * b43_phy_shm_tssi_read - Read the average of the last 4 TSSI from SHM.
+ *
+ * @shm_offset: The SHM address to read the values from.
+ *
+ * Returns the average of the 4 TSSI values, or a negative error code.
+ */
+int b43_phy_shm_tssi_read(struct b43_wldev *dev, u16 shm_offset);
+
+
#endif /* LINUX_B43_PHY_COMMON_H_ */
/* OFDM-table address caching. */
gphy->ofdmtab_addr_direction = B43_OFDMTAB_DIRECTION_UNKNOWN;
+ gphy->average_tssi = 0xFF;
lo = kzalloc(sizeof(*lo), GFP_KERNEL);
if (!lo) {
*_bbatt = clamp_val(bbatt, bb_min, bb_max);
}
-static void b43_gphy_op_xmitpower(struct b43_wldev *dev)
+static void b43_gphy_op_adjust_txpower(struct b43_wldev *dev)
{
- struct ssb_bus *bus = dev->dev->bus;
struct b43_phy *phy = &dev->phy;
struct b43_phy_g *gphy = phy->g;
- u16 tmp;
- s8 v0, v1, v2, v3;
- s8 average;
- int max_pwr;
- int desired_pwr, estimated_pwr, pwr_adjust;
- int rfatt_delta, bbatt_delta;
int rfatt, bbatt;
u8 tx_control;
- if (gphy->cur_idle_tssi == 0)
- return;
- if ((bus->boardinfo.vendor == SSB_BOARDVENDOR_BCM) &&
- (bus->boardinfo.type == SSB_BOARD_BU4306))
- return;
-
- tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x0058);
- v0 = (s8) (tmp & 0x00FF);
- v1 = (s8) ((tmp & 0xFF00) >> 8);
- tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x005A);
- v2 = (s8) (tmp & 0x00FF);
- v3 = (s8) ((tmp & 0xFF00) >> 8);
- tmp = 0;
-
- if (v0 == 0x7F || v1 == 0x7F || v2 == 0x7F
- || v3 == 0x7F) {
- tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x0070);
- v0 = (s8) (tmp & 0x00FF);
- v1 = (s8) ((tmp & 0xFF00) >> 8);
- tmp = b43_shm_read16(dev, B43_SHM_SHARED, 0x0072);
- v2 = (s8) (tmp & 0x00FF);
- v3 = (s8) ((tmp & 0xFF00) >> 8);
- if (v0 == 0x7F || v1 == 0x7F || v2 == 0x7F
- || v3 == 0x7F)
- return;
- v0 = (v0 + 0x20) & 0x3F;
- v1 = (v1 + 0x20) & 0x3F;
- v2 = (v2 + 0x20) & 0x3F;
- v3 = (v3 + 0x20) & 0x3F;
- tmp = 1;
- }
- b43_shm_clear_tssi(dev);
-
- average = (v0 + v1 + v2 + v3 + 2) / 4;
-
- if (tmp && (b43_shm_read16(dev, B43_SHM_SHARED, 0x005E) & 0x8))
- average -= 13;
-
- estimated_pwr = b43_gphy_estimate_power_out(dev, average);
-
- max_pwr = dev->dev->bus->sprom.maxpwr_bg;
- if ((dev->dev->bus->sprom.boardflags_lo
- & B43_BFL_PACTRL) && (phy->type == B43_PHYTYPE_G))
- max_pwr -= 0x3;
- if (unlikely(max_pwr <= 0)) {
- b43warn(dev->wl,
- "Invalid max-TX-power value in SPROM.\n");
- max_pwr = 60; /* fake it */
- dev->dev->bus->sprom.maxpwr_bg = max_pwr;
- }
-
- /*TODO:
- max_pwr = min(REG - dev->dev->bus->sprom.antennagain_bgphy - 0x6, max_pwr)
- where REG is the max power as per the regulatory domain
- */
-
- /* Get desired power (in Q5.2) */
- desired_pwr = INT_TO_Q52(phy->power_level);
- /* And limit it. max_pwr already is Q5.2 */
- desired_pwr = clamp_val(desired_pwr, 0, max_pwr);
- if (b43_debug(dev, B43_DBG_XMITPOWER)) {
- b43dbg(dev->wl,
- "Current TX power output: " Q52_FMT
- " dBm, " "Desired TX power output: "
- Q52_FMT " dBm\n", Q52_ARG(estimated_pwr),
- Q52_ARG(desired_pwr));
- }
-
- /* Calculate the adjustment delta. */
- pwr_adjust = desired_pwr - estimated_pwr;
-
- /* RF attenuation delta. */
- rfatt_delta = ((pwr_adjust + 7) / 8);
- /* Lower attenuation => Bigger power output. Negate it. */
- rfatt_delta = -rfatt_delta;
-
- /* Baseband attenuation delta. */
- bbatt_delta = pwr_adjust / 2;
- /* Lower attenuation => Bigger power output. Negate it. */
- bbatt_delta = -bbatt_delta;
- /* RF att affects power level 4 times as much as
- * Baseband attennuation. Subtract it. */
- bbatt_delta -= 4 * rfatt_delta;
-
- /* So do we finally need to adjust something? */
- if ((rfatt_delta == 0) && (bbatt_delta == 0))
- return;
+ spin_lock_irq(&dev->wl->irq_lock);
/* Calculate the new attenuation values. */
bbatt = gphy->bbatt.att;
- bbatt += bbatt_delta;
+ bbatt += gphy->bbatt_delta;
rfatt = gphy->rfatt.att;
- rfatt += rfatt_delta;
+ rfatt += gphy->rfatt_delta;
b43_put_attenuation_into_ranges(dev, &bbatt, &rfatt);
tx_control = gphy->tx_control;
gphy->rfatt.att = rfatt;
gphy->bbatt.att = bbatt;
+ /* We drop the lock early, so we can sleep during hardware
+ * adjustment. Possible races with op_recalc_txpower are harmless,
+ * as we will be called once again in case we raced. */
+ spin_unlock_irq(&dev->wl->irq_lock);
+
+ if (b43_debug(dev, B43_DBG_XMITPOWER))
+ b43dbg(dev->wl, "Adjusting TX power\n");
+
/* Adjust the hardware */
b43_phy_lock(dev);
b43_radio_lock(dev);
b43_phy_unlock(dev);
}
+static enum b43_txpwr_result b43_gphy_op_recalc_txpower(struct b43_wldev *dev,
+ bool ignore_tssi)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_phy_g *gphy = phy->g;
+ unsigned int average_tssi;
+ int cck_result, ofdm_result;
+ int estimated_pwr, desired_pwr, pwr_adjust;
+ int rfatt_delta, bbatt_delta;
+ unsigned int max_pwr;
+
+ /* First get the average TSSI */
+ cck_result = b43_phy_shm_tssi_read(dev, B43_SHM_SH_TSSI_CCK);
+ ofdm_result = b43_phy_shm_tssi_read(dev, B43_SHM_SH_TSSI_OFDM_G);
+ if ((cck_result < 0) && (ofdm_result < 0)) {
+ /* No TSSI information available */
+ if (!ignore_tssi)
+ goto no_adjustment_needed;
+ cck_result = 0;
+ ofdm_result = 0;
+ }
+ if (cck_result < 0)
+ average_tssi = ofdm_result;
+ else if (ofdm_result < 0)
+ average_tssi = cck_result;
+ else
+ average_tssi = (cck_result + ofdm_result) / 2;
+ /* Merge the average with the stored value. */
+ if (likely(gphy->average_tssi != 0xFF))
+ average_tssi = (average_tssi + gphy->average_tssi) / 2;
+ gphy->average_tssi = average_tssi;
+ B43_WARN_ON(average_tssi >= B43_TSSI_MAX);
+
+ /* Estimate the TX power emission based on the TSSI */
+ estimated_pwr = b43_gphy_estimate_power_out(dev, average_tssi);
+
+ B43_WARN_ON(phy->type != B43_PHYTYPE_G);
+ max_pwr = dev->dev->bus->sprom.maxpwr_bg;
+ if (dev->dev->bus->sprom.boardflags_lo & B43_BFL_PACTRL)
+ max_pwr -= 3; /* minus 0.75 */
+ if (unlikely(max_pwr >= INT_TO_Q52(30/*dBm*/))) {
+ b43warn(dev->wl,
+ "Invalid max-TX-power value in SPROM.\n");
+ max_pwr = INT_TO_Q52(20); /* fake it */
+ dev->dev->bus->sprom.maxpwr_bg = max_pwr;
+ }
+
+ /* Get desired power (in Q5.2) */
+ if (phy->desired_txpower < 0)
+ desired_pwr = INT_TO_Q52(0);
+ else
+ desired_pwr = INT_TO_Q52(phy->desired_txpower);
+ /* And limit it. max_pwr already is Q5.2 */
+ desired_pwr = clamp_val(desired_pwr, 0, max_pwr);
+ if (b43_debug(dev, B43_DBG_XMITPOWER)) {
+ b43dbg(dev->wl,
+ "[TX power] current = " Q52_FMT
+ " dBm, desired = " Q52_FMT
+ " dBm, max = " Q52_FMT "\n",
+ Q52_ARG(estimated_pwr),
+ Q52_ARG(desired_pwr),
+ Q52_ARG(max_pwr));
+ }
+
+ /* Calculate the adjustment delta. */
+ pwr_adjust = desired_pwr - estimated_pwr;
+ if (pwr_adjust == 0)
+ goto no_adjustment_needed;
+
+ /* RF attenuation delta. */
+ rfatt_delta = ((pwr_adjust + 7) / 8);
+ /* Lower attenuation => Bigger power output. Negate it. */
+ rfatt_delta = -rfatt_delta;
+
+ /* Baseband attenuation delta. */
+ bbatt_delta = pwr_adjust / 2;
+ /* Lower attenuation => Bigger power output. Negate it. */
+ bbatt_delta = -bbatt_delta;
+ /* RF att affects power level 4 times as much as
+ * Baseband attennuation. Subtract it. */
+ bbatt_delta -= 4 * rfatt_delta;
+
+ if (b43_debug(dev, B43_DBG_XMITPOWER)) {
+ int dbm = pwr_adjust < 0 ? -pwr_adjust : pwr_adjust;
+ b43dbg(dev->wl,
+ "[TX power deltas] %s" Q52_FMT " dBm => "
+ "bbatt-delta = %d, rfatt-delta = %d\n",
+ (pwr_adjust < 0 ? "-" : ""), Q52_ARG(dbm),
+ bbatt_delta, rfatt_delta);
+ }
+ /* So do we finally need to adjust something in hardware? */
+ if ((rfatt_delta == 0) && (bbatt_delta == 0))
+ goto no_adjustment_needed;
+
+ /* Save the deltas for later when we adjust the power. */
+ gphy->bbatt_delta = bbatt_delta;
+ gphy->rfatt_delta = rfatt_delta;
+
+ /* We need to adjust the TX power on the device. */
+ return B43_TXPWR_RES_NEED_ADJUST;
+
+no_adjustment_needed:
+ return B43_TXPWR_RES_DONE;
+}
+
static void b43_gphy_op_pwork_15sec(struct b43_wldev *dev)
{
struct b43_phy *phy = &dev->phy;
.get_default_chan = b43_gphy_op_get_default_chan,
.set_rx_antenna = b43_gphy_op_set_rx_antenna,
.interf_mitigation = b43_gphy_op_interf_mitigation,
- .xmitpower = b43_gphy_op_xmitpower,
+ .recalc_txpower = b43_gphy_op_recalc_txpower,
+ .adjust_txpower = b43_gphy_op_adjust_txpower,
.pwork_15sec = b43_gphy_op_pwork_15sec,
.pwork_60sec = b43_gphy_op_pwork_60sec,
};
struct b43_phy_g {
bool initialised;
- bool dyn_tssi_tbl; /* tssi2dbm is kmalloc()ed. */
/* ACI (adjacent channel interference) flags. */
bool aci_enable;
u16 minlowsig[2];
u16 minlowsigpos[2];
- /* TSSI to dBm table in use */
+ /* Pointer to the table used to convert a
+ * TSSI value to dBm-Q5.2 */
const s8 *tssi2dbm;
+ /* tssi2dbm is kmalloc()ed. Only used for free()ing. */
+ bool dyn_tssi_tbl;
/* Target idle TSSI */
int tgt_idle_tssi;
/* Current idle TSSI */
int cur_idle_tssi;
+ /* The current average TSSI.
+ * Needs irq_lock, as it's updated in the IRQ path. */
+ u8 average_tssi;
+ /* Current TX power level attenuation control values */
+ struct b43_bbatt bbatt;
+ struct b43_rfatt rfatt;
+ u8 tx_control; /* B43_TXCTL_XXX */
+ /* The calculated attenuation deltas that are used later
+ * when adjusting the actual power output. */
+ int bbatt_delta;
+ int rfatt_delta;
/* LocalOscillator control values. */
struct b43_txpower_lo_control *lo_control;
s16 lna_gain; /* LNA */
s16 pga_gain; /* PGA */
- /* Current TX power level attenuation control values */
- struct b43_bbatt bbatt;
- struct b43_rfatt rfatt;
- u8 tx_control; /* B43_TXCTL_XXX */
-
/* Current Interference Mitigation mode */
int interfmode;
/* Stack of saved values from the Interference Mitigation code.
b43_pio_handle_txstatus(dev, status);
else
b43_dma_handle_txstatus(dev, status);
+
+ b43_phy_txpower_check(dev, 0);
}
/* Fill out the mac80211 TXstatus report based on the b43-specific
projects / GitHub / moto-9609 / android_kernel_motorola_exynos9610.git / commitdiff