#include <asm/amigappc.h>
#endif
-#ifdef CONFIG_PPC64BRIDGE
-#define LOAD_BAT(n, reg, RA, RB) \
- ld RA,(n*32)+0(reg); \
- ld RB,(n*32)+8(reg); \
- mtspr SPRN_IBAT##n##U,RA; \
- mtspr SPRN_IBAT##n##L,RB; \
- ld RA,(n*32)+16(reg); \
- ld RB,(n*32)+24(reg); \
- mtspr SPRN_DBAT##n##U,RA; \
- mtspr SPRN_DBAT##n##L,RB; \
-
-#else /* CONFIG_PPC64BRIDGE */
-
/* 601 only have IBAT; cr0.eq is set on 601 when using this macro */
#define LOAD_BAT(n, reg, RA, RB) \
/* see the comment for clear_bats() -- Cort */ \
mtspr SPRN_DBAT##n##U,RA; \
mtspr SPRN_DBAT##n##L,RB; \
1:
-#endif /* CONFIG_PPC64BRIDGE */
.text
.stabs "arch/ppc/kernel/",N_SO,0,0,0f
*/
bl early_init
-/*
- * On POWER4, we first need to tweak some CPU configuration registers
- * like real mode cache inhibit or exception base
- */
-#ifdef CONFIG_POWER4
- bl __970_cpu_preinit
-#endif /* CONFIG_POWER4 */
-
#ifdef CONFIG_APUS
/* On APUS the __va/__pa constants need to be set to the correct
* values before continuing.
*/
bl mmu_off
__after_mmu_off:
-#ifndef CONFIG_POWER4
bl clear_bats
bl flush_tlbs
#if !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT)
bl setup_disp_bat
#endif
-#else /* CONFIG_POWER4 */
- bl reloc_offset
- bl initial_mm_power4
-#endif /* CONFIG_POWER4 */
/*
* Call setup_cpu for CPU 0 and initialize 6xx Idle
bl reloc_offset
bl init_idle_6xx
#endif /* CONFIG_6xx */
-#ifdef CONFIG_POWER4
- bl reloc_offset
- bl init_idle_power4
-#endif /* CONFIG_POWER4 */
#ifndef CONFIG_APUS
/* Data access exception. */
. = 0x300
-#ifdef CONFIG_PPC64BRIDGE
- b DataAccess
-DataAccessCont:
-#else
DataAccess:
EXCEPTION_PROLOG
-#endif /* CONFIG_PPC64BRIDGE */
mfspr r10,SPRN_DSISR
andis. r0,r10,0xa470 /* weird error? */
bne 1f /* if not, try to put a PTE */
mfspr r4,SPRN_DAR
EXC_XFER_EE_LITE(0x300, handle_page_fault)
-#ifdef CONFIG_PPC64BRIDGE
-/* SLB fault on data access. */
- . = 0x380
- b DataSegment
-#endif /* CONFIG_PPC64BRIDGE */
/* Instruction access exception. */
. = 0x400
-#ifdef CONFIG_PPC64BRIDGE
- b InstructionAccess
-InstructionAccessCont:
-#else
InstructionAccess:
EXCEPTION_PROLOG
-#endif /* CONFIG_PPC64BRIDGE */
andis. r0,r9,0x4000 /* no pte found? */
beq 1f /* if so, try to put a PTE */
li r3,0 /* into the hash table */
mr r5,r9
EXC_XFER_EE_LITE(0x400, handle_page_fault)
-#ifdef CONFIG_PPC64BRIDGE
-/* SLB fault on instruction access. */
- . = 0x480
- b InstructionSegment
-#endif /* CONFIG_PPC64BRIDGE */
-
/* External interrupt */
EXCEPTION(0x500, HardwareInterrupt, do_IRQ, EXC_XFER_LITE)
EXCEPTION(0x1300, Trap_13, instruction_breakpoint_exception, EXC_XFER_EE)
EXCEPTION(0x1400, SMI, SMIException, EXC_XFER_EE)
EXCEPTION(0x1500, Trap_15, unknown_exception, EXC_XFER_EE)
-#ifdef CONFIG_POWER4
- EXCEPTION(0x1600, Trap_16, unknown_exception, EXC_XFER_EE)
- EXCEPTION(0x1700, Trap_17, altivec_assist_exception, EXC_XFER_EE)
- EXCEPTION(0x1800, Trap_18, TAUException, EXC_XFER_STD)
-#else /* !CONFIG_POWER4 */
EXCEPTION(0x1600, Trap_16, altivec_assist_exception, EXC_XFER_EE)
EXCEPTION(0x1700, Trap_17, TAUException, EXC_XFER_STD)
EXCEPTION(0x1800, Trap_18, unknown_exception, EXC_XFER_EE)
-#endif /* CONFIG_POWER4 */
EXCEPTION(0x1900, Trap_19, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1a00, Trap_1a, unknown_exception, EXC_XFER_EE)
EXCEPTION(0x1b00, Trap_1b, unknown_exception, EXC_XFER_EE)
#endif /* CONFIG_ALTIVEC */
EXC_XFER_EE_LITE(0xf20, altivec_unavailable_exception)
-#ifdef CONFIG_PPC64BRIDGE
-DataAccess:
- EXCEPTION_PROLOG
- b DataAccessCont
-
-InstructionAccess:
- EXCEPTION_PROLOG
- b InstructionAccessCont
-
-DataSegment:
- EXCEPTION_PROLOG
- addi r3,r1,STACK_FRAME_OVERHEAD
- mfspr r4,SPRN_DAR
- stw r4,_DAR(r11)
- EXC_XFER_STD(0x380, unknown_exception)
-
-InstructionSegment:
- EXCEPTION_PROLOG
- addi r3,r1,STACK_FRAME_OVERHEAD
- EXC_XFER_STD(0x480, unknown_exception)
-#endif /* CONFIG_PPC64BRIDGE */
-
#ifdef CONFIG_ALTIVEC
/* Note that the AltiVec support is closely modeled after the FP
* support. Changes to one are likely to be applicable to the
.globl __secondary_start
__secondary_start:
-#ifdef CONFIG_PPC64BRIDGE
- mfmsr r0
- clrldi r0,r0,1 /* make sure it's in 32-bit mode */
- SYNC
- MTMSRD(r0)
- isync
-#endif
/* Copy some CPU settings from CPU 0 */
bl __restore_cpu_setup
lis r3,-KERNELBASE@h
bl init_idle_6xx
#endif /* CONFIG_6xx */
-#ifdef CONFIG_POWER4
- lis r3,-KERNELBASE@h
- bl init_idle_power4
-#endif /* CONFIG_POWER4 */
/* get current_thread_info and current */
lis r1,secondary_ti@ha
* Those generic dummy functions are kept for CPUs not
* included in CONFIG_6xx
*/
-#if !defined(CONFIG_6xx) && !defined(CONFIG_POWER4)
+#if !defined(CONFIG_6xx)
_GLOBAL(__save_cpu_setup)
blr
_GLOBAL(__restore_cpu_setup)
blr
-#endif /* !defined(CONFIG_6xx) && !defined(CONFIG_POWER4) */
+#endif /* !defined(CONFIG_6xx) */
/*
tophys(r6,r6)
lwz r6,_SDR1@l(r6)
mtspr SPRN_SDR1,r6
-#ifdef CONFIG_PPC64BRIDGE
- /* clear the ASR so we only use the pseudo-segment registers. */
- li r6,0
- mtasr r6
-#endif /* CONFIG_PPC64BRIDGE */
li r0,16 /* load up segment register values */
mtctr r0 /* for context 0 */
lis r3,0x2000 /* Ku = 1, VSID = 0 */
addi r3,r3,0x111 /* increment VSID */
addis r4,r4,0x1000 /* address of next segment */
bdnz 3b
-#ifndef CONFIG_POWER4
+
/* Load the BAT registers with the values set up by MMU_init.
MMU_init takes care of whether we're on a 601 or not. */
mfpvr r3
LOAD_BAT(1,r3,r4,r5)
LOAD_BAT(2,r3,r4,r5)
LOAD_BAT(3,r3,r4,r5)
-#endif /* CONFIG_POWER4 */
+
blr
/*
li r0,0
stwu r0,THREAD_SIZE-STACK_FRAME_OVERHEAD(r1)
/*
- * Do early bootinfo parsing, platform-specific initialization,
+ * Do early platform-specific initialization,
* and set up the MMU.
*/
mr r3,r31
li r4,0
isync
3:
-#ifdef CONFIG_PPC64BRIDGE
- slbie r4
-#endif /* CONFIG_PPC64BRIDGE */
mtsrin r3,r4
addi r3,r3,0x111 /* next VSID */
rlwinm r3,r3,0,8,3 /* clear out any overflow from VSID field */
sync
RFI
-#ifndef CONFIG_POWER4
/*
* Use the first pair of BAT registers to map the 1st 16MB
* of RAM to KERNELBASE. From this point on we can't safely
*/
initial_bats:
lis r11,KERNELBASE@h
-#ifndef CONFIG_PPC64BRIDGE
mfspr r9,SPRN_PVR
rlwinm r9,r9,16,16,31 /* r9 = 1 for 601, 4 for 604 */
cmpwi 0,r9,1
mtspr SPRN_IBAT1L,r10
isync
blr
-#endif /* CONFIG_PPC64BRIDGE */
4: tophys(r8,r11)
#ifdef CONFIG_SMP
ori r11,r11,BL_256M<<2|0x2 /* set up BAT registers for 604 */
#endif /* CONFIG_APUS */
-#ifdef CONFIG_PPC64BRIDGE
- /* clear out the high 32 bits in the BAT */
- clrldi r11,r11,32
- clrldi r8,r8,32
-#endif /* CONFIG_PPC64BRIDGE */
mtspr SPRN_DBAT0L,r8 /* N.B. 6xx (not 601) have valid */
mtspr SPRN_DBAT0U,r11 /* bit in upper BAT register */
mtspr SPRN_IBAT0L,r8
#endif /* !defined(CONFIG_APUS) && defined(CONFIG_BOOTX_TEXT) */
-#else /* CONFIG_POWER4 */
-/*
- * Load up the SDR1 and segment register values now
- * since we don't have the BATs.
- * Also make sure we are running in 32-bit mode.
- */
-
-initial_mm_power4:
- addis r14,r3,_SDR1@ha /* get the value from _SDR1 */
- lwz r14,_SDR1@l(r14) /* assume hash table below 4GB */
- mtspr SPRN_SDR1,r14
- slbia
- lis r4,0x2000 /* set pseudo-segment reg 12 */
- ori r5,r4,0x0ccc
- mtsr 12,r5
-#if 0
- ori r5,r4,0x0888 /* set pseudo-segment reg 8 */
- mtsr 8,r5 /* (for access to serial port) */
-#endif
-#ifdef CONFIG_BOOTX_TEXT
- ori r5,r4,0x0999 /* set pseudo-segment reg 9 */
- mtsr 9,r5 /* (for access to screen) */
-#endif
- mfmsr r0
- clrldi r0,r0,1
- sync
- mtmsr r0
- isync
- blr
-
-#endif /* CONFIG_POWER4 */
#ifdef CONFIG_8260
/* Jump into the system reset for the rom.