dt-bindings: i2c: i2c-mux: document general purpose i2c-mux bindings

Describe how a general purpose multiplexer controller is used to mux an
i2c bus.

Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt
new file mode 100644 (file)
index 0000000..2907dab
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt
@@ -0,0 +1,99 @@
+General Purpose I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses a mux controller
+from the mux subsystem to route the I2C signals.
+
+                                  .-----.  .-----.
+                                  | dev |  | dev |
+    .------------.                '-----'  '-----'
+    | SoC        |                   |        |
+    |            |          .--------+--------'
+    |   .------. |  .------+    child bus A, on MUX value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   '------' |  '--+---+    child bus B, on MUX value set to 1
+    |   .------. |     |    '----------+--------+--------.
+    |   | MUX- | |     |               |        |        |
+    |   | Ctrl |-|-----+            .-----.  .-----.  .-----.
+    |   '------' |                  | dev |  | dev |  | dev |
+    '------------'                  '-----'  '-----'  '-----'
+
+Required properties:
+- compatible: i2c-mux
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-controls: The phandle of the mux controller to use for operating the
+  mux.
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number
+  is also the mux-controller state described in ../mux/mux-controller.txt
+
+Optional properties:
+- mux-locked: If present, explicitly allow unrelated I2C transactions on the
+  parent I2C adapter at these times:
+   + during setup of the multiplexer
+   + between setup of the multiplexer and the child bus I2C transaction
+   + between the child bus I2C transaction and releasing of the multiplexer
+   + during releasing of the multiplexer
+  However, I2C transactions to devices behind all I2C multiplexers connected
+  to the same parent adapter that this multiplexer is connected to are blocked
+  for the full duration of the complete multiplexed I2C transaction (i.e.
+  including the times covered by the above list).
+  If mux-locked is not present, the multiplexer is assumed to be parent-locked.
+  This means that no unrelated I2C transactions are allowed on the parent I2C
+  adapter for the complete multiplexed I2C transaction.
+  The properties of mux-locked and parent-locked multiplexers are discussed
+  in more detail in Documentation/i2c/i2c-topology.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the relevant node's reg property will be set as the state in the
+mux controller.
+
+Example:
+       mux: mux-controller {
+               compatible = "gpio-mux";
+               #mux-control-cells = <0>;
+
+               mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
+                           <&pioA 1 GPIO_ACTIVE_HIGH>;
+       };
+
+       i2c-mux {
+               compatible = "i2c-mux";
+               mux-locked;
+               i2c-parent = <&i2c1>;
+
+               mux-controls = <&mux>;
+
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               i2c@1 {
+                       reg = <1>;
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       ssd1307: oled@3c {
+                               compatible = "solomon,ssd1307fb-i2c";
+                               reg = <0x3c>;
+                               pwms = <&pwm 4 3000>;
+                               reset-gpios = <&gpio2 7 1>;
+                               reset-active-low;
+                       };
+               };
+
+               i2c@3 {
+                       reg = <3>;
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       pca9555: pca9555@20 {
+                               compatible = "nxp,pca9555";
+                               gpio-controller;
+                               #gpio-cells = <2>;
+                               reg = <0x20>;
+                       };
+               };
+       };