sky2: convert to net_device_ops
authorStephen Hemminger <shemminger@vyatta.com>
Thu, 20 Nov 2008 05:59:54 +0000 (21:59 -0800)
committerDavid S. Miller <davem@davemloft.net>
Thu, 20 Nov 2008 06:42:44 +0000 (22:42 -0800)
Convert to new network device ops interface. Slight additional complexity
here because the second port does not allow netpoll and therefore has
different virtual function table.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sky2.c

index 4dcd1a62fb490e95768c4cc8446b839890a12194..251505125cb82faba8ffd035c45faa0bb0fd9064 100644 (file)
@@ -3979,7 +3979,7 @@ static int sky2_device_event(struct notifier_block *unused,
        struct net_device *dev = ptr;
        struct sky2_port *sky2 = netdev_priv(dev);
 
-       if (dev->open != sky2_up || !sky2_debug)
+       if (dev->netdev_ops->ndo_open != sky2_up || !sky2_debug)
                return NOTIFY_DONE;
 
        switch(event) {
@@ -4041,6 +4041,39 @@ static __exit void sky2_debug_cleanup(void)
 #define sky2_debug_cleanup()
 #endif
 
+/* Two copies of network device operations to handle special case of
+   not allowing netpoll on second port */
+static const struct net_device_ops sky2_netdev_ops[2] = {
+  {
+       .ndo_open               = sky2_up,
+       .ndo_stop               = sky2_down,
+       .ndo_do_ioctl           = sky2_ioctl,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_set_mac_address    = sky2_set_mac_address,
+       .ndo_set_multicast_list = sky2_set_multicast,
+       .ndo_change_mtu         = sky2_change_mtu,
+       .ndo_tx_timeout         = sky2_tx_timeout,
+#ifdef SKY2_VLAN_TAG_USED
+       .ndo_vlan_rx_register   = sky2_vlan_rx_register,
+#endif
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = sky2_netpoll,
+#endif
+  },
+  {
+       .ndo_open               = sky2_up,
+       .ndo_stop               = sky2_down,
+       .ndo_do_ioctl           = sky2_ioctl,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_set_mac_address    = sky2_set_mac_address,
+       .ndo_set_multicast_list = sky2_set_multicast,
+       .ndo_change_mtu         = sky2_change_mtu,
+       .ndo_tx_timeout         = sky2_tx_timeout,
+#ifdef SKY2_VLAN_TAG_USED
+       .ndo_vlan_rx_register   = sky2_vlan_rx_register,
+#endif
+  },
+};
 
 /* Initialize network device */
 static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
@@ -4057,20 +4090,10 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
 
        SET_NETDEV_DEV(dev, &hw->pdev->dev);
        dev->irq = hw->pdev->irq;
-       dev->open = sky2_up;
-       dev->stop = sky2_down;
-       dev->do_ioctl = sky2_ioctl;
        dev->hard_start_xmit = sky2_xmit_frame;
-       dev->set_multicast_list = sky2_set_multicast;
-       dev->set_mac_address = sky2_set_mac_address;
-       dev->change_mtu = sky2_change_mtu;
        SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops);
-       dev->tx_timeout = sky2_tx_timeout;
        dev->watchdog_timeo = TX_WATCHDOG;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       if (port == 0)
-               dev->poll_controller = sky2_netpoll;
-#endif
+       dev->netdev_ops = &sky2_netdev_ops[port];
 
        sky2 = netdev_priv(dev);
        sky2->netdev = dev;
@@ -4104,7 +4127,6 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw,
        if (!(sky2->hw->chip_id == CHIP_ID_YUKON_FE_P &&
              sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0)) {
                dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
-               dev->vlan_rx_register = sky2_vlan_rx_register;
        }
 #endif