bnx2x: Adjust BCM84833 to BCM578xx
authorYaniv Rosner <yanivr@broadcom.com>
Tue, 14 Jun 2011 01:34:27 +0000 (01:34 +0000)
committerDavid S. Miller <davem@conan.davemloft.net>
Wed, 15 Jun 2011 14:56:57 +0000 (10:56 -0400)
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
drivers/net/bnx2x/bnx2x_link.c
drivers/net/bnx2x/bnx2x_main.c

index a5c34880b39eb607d8b771602413e788ec4a0ba2..241b1e42c3759480c1902a28767ac26c8660ec45 100644 (file)
@@ -9198,6 +9198,52 @@ static int bnx2x_84833_pair_swap_cfg(struct bnx2x_phy *phy,
        return 0;
 }
 
+
+static int bnx2x_84833_common_init_phy(struct bnx2x *bp,
+                                               u32 shmem_base_path[],
+                                               u32 chip_id)
+{
+       u32 reset_pin[2];
+       u32 idx;
+       u8 reset_gpios;
+       if (CHIP_IS_E3(bp)) {
+               /* Assume that these will be GPIOs, not EPIOs. */
+               for (idx = 0; idx < 2; idx++) {
+                       /* Map config param to register bit. */
+                       reset_pin[idx] = REG_RD(bp, shmem_base_path[idx] +
+                               offsetof(struct shmem_region,
+                               dev_info.port_hw_config[0].e3_cmn_pin_cfg));
+                       reset_pin[idx] = (reset_pin[idx] &
+                               PORT_HW_CFG_E3_PHY_RESET_MASK) >>
+                               PORT_HW_CFG_E3_PHY_RESET_SHIFT;
+                       reset_pin[idx] -= PIN_CFG_GPIO0_P0;
+                       reset_pin[idx] = (1 << reset_pin[idx]);
+               }
+               reset_gpios = (u8)(reset_pin[0] | reset_pin[1]);
+       } else {
+               /* E2, look from diff place of shmem. */
+               for (idx = 0; idx < 2; idx++) {
+                       reset_pin[idx] = REG_RD(bp, shmem_base_path[idx] +
+                               offsetof(struct shmem_region,
+                               dev_info.port_hw_config[0].default_cfg));
+                       reset_pin[idx] &= PORT_HW_CFG_EXT_PHY_GPIO_RST_MASK;
+                       reset_pin[idx] -= PORT_HW_CFG_EXT_PHY_GPIO_RST_GPIO0_P0;
+                       reset_pin[idx] >>= PORT_HW_CFG_EXT_PHY_GPIO_RST_SHIFT;
+                       reset_pin[idx] = (1 << reset_pin[idx]);
+               }
+               reset_gpios = (u8)(reset_pin[0] | reset_pin[1]);
+       }
+
+       bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_LOW);
+       udelay(10);
+       bnx2x_set_mult_gpio(bp, reset_gpios, MISC_REGISTERS_GPIO_OUTPUT_HIGH);
+       msleep(800);
+       DP(NETIF_MSG_LINK, "84833 reset pulse on pin values 0x%x\n",
+               reset_gpios);
+
+       return 0;
+}
+
 static int bnx2x_848x3_config_init(struct bnx2x_phy *phy,
                                   struct link_params *params,
                                   struct link_vars *vars)
@@ -9263,8 +9309,14 @@ static int bnx2x_848x3_config_init(struct bnx2x_phy *phy,
                 MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN |
                 MDIO_CTL_REG_84823_MEDIA_PRIORITY_MASK |
                 MDIO_CTL_REG_84823_MEDIA_FIBER_1G);
-       val |= MDIO_CTL_REG_84823_CTRL_MAC_XFI |
-               MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L;
+
+       if (CHIP_IS_E3(bp)) {
+               val &= ~(MDIO_CTL_REG_84823_MEDIA_MAC_MASK |
+                        MDIO_CTL_REG_84823_MEDIA_LINE_MASK);
+       } else {
+               val |= (MDIO_CTL_REG_84823_CTRL_MAC_XFI |
+                       MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L);
+       }
 
        actual_phy_selection = bnx2x_phy_selection(params);
 
@@ -9435,6 +9487,7 @@ static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy,
 {
        struct bnx2x *bp = params->bp;
        u8 port;
+       u16 val16;
 
        if (!(CHIP_IS_E1(bp)))
                port = BP_PATH(bp);
@@ -9446,9 +9499,14 @@ static void bnx2x_848x3_link_reset(struct bnx2x_phy *phy,
                               MISC_REGISTERS_GPIO_OUTPUT_LOW,
                               port);
        } else {
-               bnx2x_cl45_write(bp, phy,
-                               MDIO_PMA_DEVAD,
-                               MDIO_PMA_REG_CTRL, 0x800);
+               bnx2x_cl45_read(bp, phy,
+                               MDIO_CTL_DEVAD,
+                               0x400f, &val16);
+               /* Put to low power mode on newer FW */
+               if ((val16 & 0x303f) > 0x1009)
+                       bnx2x_cl45_write(bp, phy,
+                                       MDIO_PMA_DEVAD,
+                                       MDIO_PMA_REG_CTRL, 0x800);
        }
 }
 
@@ -9647,7 +9705,17 @@ static void bnx2x_848xx_set_link_led(struct bnx2x_phy *phy,
                }
                break;
        }
+
+       /*
+        * This is a workaround for E3+84833 until autoneg
+        * restart is fixed in f/w
+        */
+       if (CHIP_IS_E3(bp)) {
+               bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+                               MDIO_WC_REG_GP2_STATUS_GP_2_1, &val);
+       }
 }
+
 /******************************************************************/
 /*                     54616S PHY SECTION                        */
 /******************************************************************/
@@ -11700,6 +11768,13 @@ static int bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[],
                                                shmem2_base_path,
                                                phy_index, chip_id);
                break;
+       case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833:
+               /*
+                * GPIO3's are linked, and so both need to be toggled
+                * to obtain required 2us pulse.
+                */
+               rc = bnx2x_84833_common_init_phy(bp, shmem_base_path, chip_id);
+               break;
        case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
                rc = -EINVAL;
                break;
index 0dddba9532c1c5ecaca7b7f74549dc39628cbfd8..29c67029c756eea612f59b7e78369c14b7383c03 100644 (file)
@@ -1955,6 +1955,53 @@ int bnx2x_set_gpio(struct bnx2x *bp, int gpio_num, u32 mode, u8 port)
        return 0;
 }
 
+int bnx2x_set_mult_gpio(struct bnx2x *bp, u8 pins, u32 mode)
+{
+       u32 gpio_reg = 0;
+       int rc = 0;
+
+       /* Any port swapping should be handled by caller. */
+
+       bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_GPIO);
+       /* read GPIO and mask except the float bits */
+       gpio_reg = REG_RD(bp, MISC_REG_GPIO);
+       gpio_reg &= ~(pins << MISC_REGISTERS_GPIO_FLOAT_POS);
+       gpio_reg &= ~(pins << MISC_REGISTERS_GPIO_CLR_POS);
+       gpio_reg &= ~(pins << MISC_REGISTERS_GPIO_SET_POS);
+
+       switch (mode) {
+       case MISC_REGISTERS_GPIO_OUTPUT_LOW:
+               DP(NETIF_MSG_LINK, "Set GPIO 0x%x -> output low\n", pins);
+               /* set CLR */
+               gpio_reg |= (pins << MISC_REGISTERS_GPIO_CLR_POS);
+               break;
+
+       case MISC_REGISTERS_GPIO_OUTPUT_HIGH:
+               DP(NETIF_MSG_LINK, "Set GPIO 0x%x -> output high\n", pins);
+               /* set SET */
+               gpio_reg |= (pins << MISC_REGISTERS_GPIO_SET_POS);
+               break;
+
+       case MISC_REGISTERS_GPIO_INPUT_HI_Z:
+               DP(NETIF_MSG_LINK, "Set GPIO 0x%x -> input\n", pins);
+               /* set FLOAT */
+               gpio_reg |= (pins << MISC_REGISTERS_GPIO_FLOAT_POS);
+               break;
+
+       default:
+               BNX2X_ERR("Invalid GPIO mode assignment %d\n", mode);
+               rc = -EINVAL;
+               break;
+       }
+
+       if (rc == 0)
+               REG_WR(bp, MISC_REG_GPIO, gpio_reg);
+
+       bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_GPIO);
+
+       return rc;
+}
+
 int bnx2x_set_gpio_int(struct bnx2x *bp, int gpio_num, u32 mode, u8 port)
 {
        /* The GPIO should be swapped if swap register is set and active */