cxgb3: Add 1G fiber support
authorDivy Le Ray <divy@chelsio.com>
Thu, 9 Oct 2008 00:40:28 +0000 (17:40 -0700)
committerDavid S. Miller <davem@davemloft.net>
Thu, 9 Oct 2008 00:40:28 +0000 (17:40 -0700)
Add support for 1G optical Vitesse PHY.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cxgb3/common.h
drivers/net/cxgb3/t3_hw.c
drivers/net/cxgb3/vsc8211.c

index 416d3dd258e0f82537388cb991ce3b206c727061..593fb643a615086ff6a16cb8ed88844bf0705804 100644 (file)
@@ -691,6 +691,7 @@ int t3_mdio_change_bits(struct cphy *phy, int mmd, int reg, unsigned int clear,
                        unsigned int set);
 int t3_phy_reset(struct cphy *phy, int mmd, int wait);
 int t3_phy_advertise(struct cphy *phy, unsigned int advert);
+int t3_phy_advertise_fiber(struct cphy *phy, unsigned int advert);
 int t3_set_phy_speed_duplex(struct cphy *phy, int speed, int duplex);
 int t3_phy_lasi_intr_enable(struct cphy *phy);
 int t3_phy_lasi_intr_disable(struct cphy *phy);
index 9d9c0bafb5c76dcd3654bd535b1e80960f66a470..4da5b09b9bc29221ec7a2eae370bb9b8832a398a 100644 (file)
@@ -407,6 +407,29 @@ int t3_phy_advertise(struct cphy *phy, unsigned int advert)
        return mdio_write(phy, 0, MII_ADVERTISE, val);
 }
 
+/**
+ *     t3_phy_advertise_fiber - set fiber PHY advertisement register
+ *     @phy: the PHY to operate on
+ *     @advert: bitmap of capabilities the PHY should advertise
+ *
+ *     Sets a fiber PHY's advertisement register to advertise the
+ *     requested capabilities.
+ */
+int t3_phy_advertise_fiber(struct cphy *phy, unsigned int advert)
+{
+       unsigned int val = 0;
+
+       if (advert & ADVERTISED_1000baseT_Half)
+               val |= ADVERTISE_1000XHALF;
+       if (advert & ADVERTISED_1000baseT_Full)
+               val |= ADVERTISE_1000XFULL;
+       if (advert & ADVERTISED_Pause)
+               val |= ADVERTISE_1000XPAUSE;
+       if (advert & ADVERTISED_Asym_Pause)
+               val |= ADVERTISE_1000XPSE_ASYM;
+       return mdio_write(phy, 0, MII_ADVERTISE, val);
+}
+
 /**
  *     t3_set_phy_speed_duplex - force PHY speed and duplex
  *     @phy: the PHY to operate on
index 68e6334c206a99580e6fe805b3bb464f74c5272b..306c2dc4ab34884d2687fdae9c302d80b01b2426 100644 (file)
 
 /* VSC8211 PHY specific registers. */
 enum {
+       VSC8211_SIGDET_CTRL = 19,
+       VSC8211_EXT_CTRL = 23,
        VSC8211_INTR_ENABLE = 25,
        VSC8211_INTR_STATUS = 26,
+       VSC8211_LED_CTRL = 27,
        VSC8211_AUX_CTRL_STAT = 28,
+       VSC8211_EXT_PAGE_AXS = 31,
 };
 
 enum {
        VSC_INTR_RX_ERR = 1 << 0,
-       VSC_INTR_MS_ERR = 1 << 1,       /* master/slave resolution error */
-       VSC_INTR_CABLE = 1 << 2,        /* cable impairment */
-       VSC_INTR_FALSE_CARR = 1 << 3,   /* false carrier */
-       VSC_INTR_MEDIA_CHG = 1 << 4,    /* AMS media change */
-       VSC_INTR_RX_FIFO = 1 << 5,      /* Rx FIFO over/underflow */
-       VSC_INTR_TX_FIFO = 1 << 6,      /* Tx FIFO over/underflow */
-       VSC_INTR_DESCRAMBL = 1 << 7,    /* descrambler lock-lost */
-       VSC_INTR_SYMBOL_ERR = 1 << 8,   /* symbol error */
-       VSC_INTR_NEG_DONE = 1 << 10,    /* autoneg done */
-       VSC_INTR_NEG_ERR = 1 << 11,     /* autoneg error */
-       VSC_INTR_LINK_CHG = 1 << 13,    /* link change */
-       VSC_INTR_ENABLE = 1 << 15,      /* interrupt enable */
+       VSC_INTR_MS_ERR = 1 << 1,  /* master/slave resolution error */
+       VSC_INTR_CABLE = 1 << 2,  /* cable impairment */
+       VSC_INTR_FALSE_CARR = 1 << 3,  /* false carrier */
+       VSC_INTR_MEDIA_CHG = 1 << 4,  /* AMS media change */
+       VSC_INTR_RX_FIFO = 1 << 5,  /* Rx FIFO over/underflow */
+       VSC_INTR_TX_FIFO = 1 << 6,  /* Tx FIFO over/underflow */
+       VSC_INTR_DESCRAMBL = 1 << 7,  /* descrambler lock-lost */
+       VSC_INTR_SYMBOL_ERR = 1 << 8,  /* symbol error */
+       VSC_INTR_NEG_DONE = 1 << 10, /* autoneg done */
+       VSC_INTR_NEG_ERR = 1 << 11, /* autoneg error */
+       VSC_INTR_DPLX_CHG = 1 << 12, /* duplex change */
+       VSC_INTR_LINK_CHG = 1 << 13, /* link change */
+       VSC_INTR_SPD_CHG = 1 << 14, /* speed change */
+       VSC_INTR_ENABLE = 1 << 15, /* interrupt enable */
+};
+
+enum {
+       VSC_CTRL_CLAUSE37_VIEW = 1 << 4,   /* Switch to Clause 37 view */
+       VSC_CTRL_MEDIA_MODE_HI = 0xf000    /* High part of media mode select */
 };
 
 #define CFG_CHG_INTR_MASK (VSC_INTR_LINK_CHG | VSC_INTR_NEG_ERR | \
+                          VSC_INTR_DPLX_CHG | VSC_INTR_SPD_CHG | \
                           VSC_INTR_NEG_DONE)
 #define INTR_MASK (CFG_CHG_INTR_MASK | VSC_INTR_TX_FIFO | VSC_INTR_RX_FIFO | \
                   VSC_INTR_ENABLE)
@@ -184,6 +196,112 @@ static int vsc8211_get_link_status(struct cphy *cphy, int *link_ok,
        return 0;
 }
 
+static int vsc8211_get_link_status_fiber(struct cphy *cphy, int *link_ok,
+                                        int *speed, int *duplex, int *fc)
+{
+       unsigned int bmcr, status, lpa, adv;
+       int err, sp = -1, dplx = -1, pause = 0;
+
+       err = mdio_read(cphy, 0, MII_BMCR, &bmcr);
+       if (!err)
+               err = mdio_read(cphy, 0, MII_BMSR, &status);
+       if (err)
+               return err;
+
+       if (link_ok) {
+               /*
+                * BMSR_LSTATUS is latch-low, so if it is 0 we need to read it
+                * once more to get the current link state.
+                */
+               if (!(status & BMSR_LSTATUS))
+                       err = mdio_read(cphy, 0, MII_BMSR, &status);
+               if (err)
+                       return err;
+               *link_ok = (status & BMSR_LSTATUS) != 0;
+       }
+       if (!(bmcr & BMCR_ANENABLE)) {
+               dplx = (bmcr & BMCR_FULLDPLX) ? DUPLEX_FULL : DUPLEX_HALF;
+               if (bmcr & BMCR_SPEED1000)
+                       sp = SPEED_1000;
+               else if (bmcr & BMCR_SPEED100)
+                       sp = SPEED_100;
+               else
+                       sp = SPEED_10;
+       } else if (status & BMSR_ANEGCOMPLETE) {
+               err = mdio_read(cphy, 0, MII_LPA, &lpa);
+               if (!err)
+                       err = mdio_read(cphy, 0, MII_ADVERTISE, &adv);
+               if (err)
+                       return err;
+
+               if (adv & lpa & ADVERTISE_1000XFULL) {
+                       dplx = DUPLEX_FULL;
+                       sp = SPEED_1000;
+               } else if (adv & lpa & ADVERTISE_1000XHALF) {
+                       dplx = DUPLEX_HALF;
+                       sp = SPEED_1000;
+               }
+
+               if (fc && dplx == DUPLEX_FULL) {
+                       if (lpa & adv & ADVERTISE_1000XPAUSE)
+                               pause = PAUSE_RX | PAUSE_TX;
+                       else if ((lpa & ADVERTISE_1000XPAUSE) &&
+                                (adv & lpa & ADVERTISE_1000XPSE_ASYM))
+                               pause = PAUSE_TX;
+                       else if ((lpa & ADVERTISE_1000XPSE_ASYM) &&
+                                (adv & ADVERTISE_1000XPAUSE))
+                               pause = PAUSE_RX;
+               }
+       }
+       if (speed)
+               *speed = sp;
+       if (duplex)
+               *duplex = dplx;
+       if (fc)
+               *fc = pause;
+       return 0;
+}
+
+/*
+ * Enable/disable auto MDI/MDI-X in forced link speed mode.
+ */
+static int vsc8211_set_automdi(struct cphy *phy, int enable)
+{
+       int err;
+
+       err = mdio_write(phy, 0, VSC8211_EXT_PAGE_AXS, 0x52b5);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, 18, 0x12);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, 17, enable ? 0x2803 : 0x3003);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, 16, 0x87fa);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, VSC8211_EXT_PAGE_AXS, 0);
+       if (err)
+               return err;
+
+       return 0;
+}
+
+int vsc8211_set_speed_duplex(struct cphy *phy, int speed, int duplex)
+{
+       int err;
+
+       err = t3_set_phy_speed_duplex(phy, speed, duplex);
+       if (!err)
+               err = vsc8211_set_automdi(phy, 1);
+       return err;
+}
+
 static int vsc8211_power_down(struct cphy *cphy, int enable)
 {
        return t3_mdio_change_bits(cphy, 0, MII_BMCR, BMCR_PDOWN,
@@ -221,12 +339,66 @@ static struct cphy_ops vsc8211_ops = {
        .power_down = vsc8211_power_down,
 };
 
+static struct cphy_ops vsc8211_fiber_ops = {
+       .reset = vsc8211_reset,
+       .intr_enable = vsc8211_intr_enable,
+       .intr_disable = vsc8211_intr_disable,
+       .intr_clear = vsc8211_intr_clear,
+       .intr_handler = vsc8211_intr_handler,
+       .autoneg_enable = vsc8211_autoneg_enable,
+       .autoneg_restart = vsc8211_autoneg_restart,
+       .advertise = t3_phy_advertise_fiber,
+       .set_speed_duplex = t3_set_phy_speed_duplex,
+       .get_link_status = vsc8211_get_link_status_fiber,
+       .power_down = vsc8211_power_down,
+};
+
 int t3_vsc8211_phy_prep(struct cphy *phy, struct adapter *adapter,
                        int phy_addr, const struct mdio_ops *mdio_ops)
 {
+       int err;
+       unsigned int val;
+
        cphy_init(phy, adapter, phy_addr, &vsc8211_ops, mdio_ops,
                  SUPPORTED_10baseT_Full | SUPPORTED_100baseT_Full |
                  SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg | SUPPORTED_MII |
                  SUPPORTED_TP | SUPPORTED_IRQ, "10/100/1000BASE-T");
+       msleep(20);       /* PHY needs ~10ms to start responding to MDIO */
+
+       err = mdio_read(phy, 0, VSC8211_EXT_CTRL, &val);
+       if (err)
+               return err;
+       if (val & VSC_CTRL_MEDIA_MODE_HI) {
+               /* copper interface, just need to configure the LEDs */
+               return mdio_write(phy, 0, VSC8211_LED_CTRL, 0x100);
+       }
+
+       phy->caps = SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg |
+                   SUPPORTED_MII | SUPPORTED_FIBRE | SUPPORTED_IRQ;
+       phy->desc = "1000BASE-X";
+       phy->ops = &vsc8211_fiber_ops;
+
+       err = mdio_write(phy, 0, VSC8211_EXT_PAGE_AXS, 1);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, VSC8211_SIGDET_CTRL, 1);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, VSC8211_EXT_PAGE_AXS, 0);
+       if (err)
+               return err;
+
+       err = mdio_write(phy, 0, VSC8211_EXT_CTRL,
+                        val | VSC_CTRL_CLAUSE37_VIEW);
+       if (err)
+               return err;
+
+       err = vsc8211_reset(phy, 0);
+       if (err)
+               return err;
+
+       udelay(5); /* delay after reset before next SMI */
        return 0;
 }