{
struct dw_mci *host = s->private;
+ pm_runtime_get_sync(host->dev);
+
seq_printf(s, "STATUS:\t0x%08x\n", mci_readl(host, STATUS));
seq_printf(s, "RINTSTS:\t0x%08x\n", mci_readl(host, RINTSTS));
seq_printf(s, "CMD:\t0x%08x\n", mci_readl(host, CMD));
seq_printf(s, "INTMASK:\t0x%08x\n", mci_readl(host, INTMASK));
seq_printf(s, "CLKENA:\t0x%08x\n", mci_readl(host, CLKENA));
+ pm_runtime_put_autosuspend(host->dev);
+
return 0;
}
static inline void dw_mci_set_cto(struct dw_mci *host)
{
unsigned int cto_clks;
+ unsigned int cto_div;
unsigned int cto_ms;
+ unsigned long irqflags;
cto_clks = mci_readl(host, TMOUT) & 0xff;
- cto_ms = DIV_ROUND_UP(cto_clks, host->bus_hz / 1000);
+ cto_div = (mci_readl(host, CLKDIV) & 0xff) * 2;
+ if (cto_div == 0)
+ cto_div = 1;
+
+ cto_ms = DIV_ROUND_UP_ULL((u64)MSEC_PER_SEC * cto_clks * cto_div,
+ host->bus_hz);
/* add a bit spare time */
cto_ms += 10;
- mod_timer(&host->cto_timer,
- jiffies + msecs_to_jiffies(cto_ms) + 1);
+ /*
+ * The durations we're working with are fairly short so we have to be
+ * extra careful about synchronization here. Specifically in hardware a
+ * command timeout is _at most_ 5.1 ms, so that means we expect an
+ * interrupt (either command done or timeout) to come rather quickly
+ * after the mci_writel. ...but just in case we have a long interrupt
+ * latency let's add a bit of paranoia.
+ *
+ * In general we'll assume that at least an interrupt will be asserted
+ * in hardware by the time the cto_timer runs. ...and if it hasn't
+ * been asserted in hardware by that time then we'll assume it'll never
+ * come.
+ */
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
+ mod_timer(&host->cto_timer,
+ jiffies + msecs_to_jiffies(cto_ms) + 1);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
}
static void dw_mci_start_command(struct dw_mci *host,
wmb(); /* drain writebuffer */
dw_mci_wait_while_busy(host, cmd_flags);
+ mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
+
/* response expected command only */
if (cmd_flags & SDMMC_CMD_RESP_EXP)
dw_mci_set_cto(host);
-
- mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
}
static inline void send_stop_abort(struct dw_mci *host, struct mmc_data *data)
(sizeof(struct idmac_desc_64addr) *
(i + 1))) >> 32;
/* Initialize reserved and buffer size fields to "0" */
+ p->des0 = 0;
p->des1 = 0;
p->des2 = 0;
p->des3 = 0;
i++, p++) {
p->des3 = cpu_to_le32(host->sg_dma +
(sizeof(struct idmac_desc) * (i + 1)));
+ p->des0 = 0;
p->des1 = 0;
}
* It's used when HS400 mode is enabled.
*/
if (data->flags & MMC_DATA_WRITE &&
- !(host->timing != MMC_TIMING_MMC_HS400))
- return;
+ host->timing != MMC_TIMING_MMC_HS400)
+ goto disable;
if (data->flags & MMC_DATA_WRITE)
enable = SDMMC_CARD_WR_THR_EN;
enable = SDMMC_CARD_RD_THR_EN;
if (host->timing != MMC_TIMING_MMC_HS200 &&
- host->timing != MMC_TIMING_UHS_SDR104)
+ host->timing != MMC_TIMING_UHS_SDR104 &&
+ host->timing != MMC_TIMING_MMC_HS400)
goto disable;
blksz_depth = blksz / (1 << host->data_shift);
}
if (host->use_dma == TRANS_MODE_IDMAC)
- /* It is also recommended that we reset and reprogram idmac */
- dw_mci_idmac_reset(host);
+ /* It is also required that we reinit idmac */
+ dw_mci_idmac_init(host);
ret = true;
static void dw_mci_set_drto(struct dw_mci *host)
{
unsigned int drto_clks;
+ unsigned int drto_div;
unsigned int drto_ms;
drto_clks = mci_readl(host, TMOUT) >> 8;
- drto_ms = DIV_ROUND_UP(drto_clks, host->bus_hz / 1000);
+ drto_div = (mci_readl(host, CLKDIV) & 0xff) * 2;
+ if (drto_div == 0)
+ drto_div = 1;
+
+ drto_ms = DIV_ROUND_UP_ULL((u64)MSEC_PER_SEC * drto_clks * drto_div,
+ host->bus_hz);
/* add a bit spare time */
drto_ms += 10;
mod_timer(&host->dto_timer, jiffies + msecs_to_jiffies(drto_ms));
}
+static bool dw_mci_clear_pending_cmd_complete(struct dw_mci *host)
+{
+ if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
+ return false;
+
+ /*
+ * Really be certain that the timer has stopped. This is a bit of
+ * paranoia and could only really happen if we had really bad
+ * interrupt latency and the interrupt routine and timeout were
+ * running concurrently so that the del_timer() in the interrupt
+ * handler couldn't run.
+ */
+ WARN_ON(del_timer_sync(&host->cto_timer));
+ clear_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+
+ return true;
+}
+
static void dw_mci_tasklet_func(unsigned long priv)
{
struct dw_mci *host = (struct dw_mci *)priv;
case STATE_SENDING_CMD11:
case STATE_SENDING_CMD:
- if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
- &host->pending_events))
+ if (!dw_mci_clear_pending_cmd_complete(host))
break;
cmd = host->cmd;
/* fall through */
case STATE_SENDING_STOP:
- if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
- &host->pending_events))
+ if (!dw_mci_clear_pending_cmd_complete(host))
break;
/* CMD error in data command */
static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status)
{
+ del_timer(&host->cto_timer);
+
if (!host->cmd_status)
host->cmd_status = status;
struct dw_mci *host = dev_id;
u32 pending;
struct dw_mci_slot *slot = host->slot;
+ unsigned long irqflags;
pending = mci_readl(host, MINTSTS); /* read-only mask reg */
/* Check volt switch first, since it can look like an error */
if ((host->state == STATE_SENDING_CMD11) &&
(pending & SDMMC_INT_VOLT_SWITCH)) {
- unsigned long irqflags;
-
mci_writel(host, RINTSTS, SDMMC_INT_VOLT_SWITCH);
pending &= ~SDMMC_INT_VOLT_SWITCH;
}
if (pending & DW_MCI_CMD_ERROR_FLAGS) {
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+
del_timer(&host->cto_timer);
mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
host->cmd_status = pending;
smp_wmb(); /* drain writebuffer */
set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
}
if (pending & DW_MCI_DATA_ERROR_FLAGS) {
}
if (pending & SDMMC_INT_CMD_DONE) {
- del_timer(&host->cto_timer);
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+
mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
dw_mci_cmd_interrupt(host, pending);
+
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
}
if (pending & SDMMC_INT_CD) {
return IRQ_HANDLED;
}
+static int dw_mci_init_slot_caps(struct dw_mci_slot *slot)
+{
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ struct mmc_host *mmc = slot->mmc;
+ int ctrl_id;
+
+ if (host->pdata->caps)
+ mmc->caps = host->pdata->caps;
+
+ /*
+ * Support MMC_CAP_ERASE by default.
+ * It needs to use trim/discard/erase commands.
+ */
+ mmc->caps |= MMC_CAP_ERASE;
+
+ if (host->pdata->pm_caps)
+ mmc->pm_caps = host->pdata->pm_caps;
+
+ if (host->dev->of_node) {
+ ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
+ if (ctrl_id < 0)
+ ctrl_id = 0;
+ } else {
+ ctrl_id = to_platform_device(host->dev)->id;
+ }
+
+ if (drv_data && drv_data->caps) {
+ if (ctrl_id >= drv_data->num_caps) {
+ dev_err(host->dev, "invalid controller id %d\n",
+ ctrl_id);
+ return -EINVAL;
+ }
+ mmc->caps |= drv_data->caps[ctrl_id];
+ }
+
+ if (host->pdata->caps2)
+ mmc->caps2 = host->pdata->caps2;
+
+ /* Process SDIO IRQs through the sdio_irq_work. */
+ if (mmc->caps & MMC_CAP_SDIO_IRQ)
+ mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
+
+ return 0;
+}
+
static int dw_mci_init_slot(struct dw_mci *host)
{
struct mmc_host *mmc;
struct dw_mci_slot *slot;
- const struct dw_mci_drv_data *drv_data = host->drv_data;
- int ctrl_id, ret;
+ int ret;
u32 freq[2];
mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
if (!mmc->ocr_avail)
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
- if (host->pdata->caps)
- mmc->caps = host->pdata->caps;
-
- /*
- * Support MMC_CAP_ERASE by default.
- * It needs to use trim/discard/erase commands.
- */
- mmc->caps |= MMC_CAP_ERASE;
-
- if (host->pdata->pm_caps)
- mmc->pm_caps = host->pdata->pm_caps;
-
- if (host->dev->of_node) {
- ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
- if (ctrl_id < 0)
- ctrl_id = 0;
- } else {
- ctrl_id = to_platform_device(host->dev)->id;
- }
- if (drv_data && drv_data->caps)
- mmc->caps |= drv_data->caps[ctrl_id];
-
- if (host->pdata->caps2)
- mmc->caps2 = host->pdata->caps2;
-
ret = mmc_of_parse(mmc);
if (ret)
goto err_host_allocated;
- /* Process SDIO IRQs through the sdio_irq_work. */
- if (mmc->caps & MMC_CAP_SDIO_IRQ)
- mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
+ ret = dw_mci_init_slot_caps(slot);
+ if (ret)
+ goto err_host_allocated;
/* Useful defaults if platform data is unset. */
if (host->use_dma == TRANS_MODE_IDMAC) {
static void dw_mci_cto_timer(unsigned long arg)
{
struct dw_mci *host = (struct dw_mci *)arg;
+ unsigned long irqflags;
+ u32 pending;
+
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ /*
+ * If somehow we have very bad interrupt latency it's remotely possible
+ * that the timer could fire while the interrupt is still pending or
+ * while the interrupt is midway through running. Let's be paranoid
+ * and detect those two cases. Note that this is paranoia is somewhat
+ * justified because in this function we don't actually cancel the
+ * pending command in the controller--we just assume it will never come.
+ */
+ pending = mci_readl(host, MINTSTS); /* read-only mask reg */
+ if (pending & (DW_MCI_CMD_ERROR_FLAGS | SDMMC_INT_CMD_DONE)) {
+ /* The interrupt should fire; no need to act but we can warn */
+ dev_warn(host->dev, "Unexpected interrupt latency\n");
+ goto exit;
+ }
+ if (test_bit(EVENT_CMD_COMPLETE, &host->pending_events)) {
+ /* Presumably interrupt handler couldn't delete the timer */
+ dev_warn(host->dev, "CTO timeout when already completed\n");
+ goto exit;
+ }
+
+ /*
+ * Continued paranoia to make sure we're in the state we expect.
+ * This paranoia isn't really justified but it seems good to be safe.
+ */
switch (host->state) {
case STATE_SENDING_CMD11:
case STATE_SENDING_CMD:
host->state);
break;
}
+
+exit:
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
}
static void dw_mci_dto_timer(unsigned long arg)