drivers/video/backlight/Kconfig

   1 #
   2 # Backlight & LCD drivers configuration
   3 #
   4
   5 menuconfig BACKLIGHT_LCD_SUPPORT
   6         bool "Backlight & LCD device support"
   7         help
   8           Enable this to be able to choose the drivers for controlling the
   9           backlight and the LCD panel on some platforms, for example on PDAs.
  10
  11 if BACKLIGHT_LCD_SUPPORT
  12
  13 #
  14 # LCD
  15 #
  16 config LCD_CLASS_DEVICE
  17         tristate "Lowlevel LCD controls"
  18         default m
  19         help
  20           This framework adds support for low-level control of LCD.
  21           Some framebuffer devices connect to platform-specific LCD modules
  22           in order to have a platform-specific way to control the flat panel
  23           (contrast and applying power to the LCD (not to the backlight!)).
  24
  25           To have support for your specific LCD panel you will have to
  26           select the proper drivers which depend on this option.
  27
  28 if LCD_CLASS_DEVICE
  29
  30 config LCD_CORGI
  31         tristate "LCD Panel support for SHARP corgi/spitz model"
  32         depends on SPI_MASTER && PXA_SHARPSL
  33         help
  34           Say y here to support the LCD panels usually found on SHARP
  35           corgi (C7x0) and spitz (Cxx00) models.
  36
  37 config LCD_L4F00242T03
  38         tristate "Epson L4F00242T03 LCD"
  39         depends on SPI_MASTER && GPIOLIB
  40         help
  41           SPI driver for Epson L4F00242T03. This provides basic support
  42           for init and powering the LCD up/down through a sysfs interface.
  43
  44 config LCD_LMS283GF05
  45         tristate "Samsung LMS283GF05 LCD"
  46         depends on SPI_MASTER && GPIOLIB
  47         help
  48           SPI driver for Samsung LMS283GF05. This provides basic support
  49           for powering the LCD up/down through a sysfs interface.
  50
  51 config LCD_LTV350QV
  52         tristate "Samsung LTV350QV LCD Panel"
  53         depends on SPI_MASTER
  54         help
  55           If you have a Samsung LTV350QV LCD panel, say y to include a
  56           power control driver for it.  The panel starts up in power
  57           off state, so you need this driver in order to see any
  58           output.
  59
  60           The LTV350QV panel is present on all ATSTK1000 boards.
  61
  62 config LCD_ILI922X
  63         tristate "ILI Technology ILI9221/ILI9222 support"
  64         depends on SPI
  65         help
  66           If you have a panel based on the ILI9221/9222 controller
  67           chip then say y to include a driver for it.
  68
  69 config LCD_ILI9320
  70         tristate "ILI Technology ILI9320 controller support"
  71         depends on SPI
  72         help
  73           If you have a panel based on the ILI9320 controller chip
  74           then say y to include a power driver for it.
  75
  76 config LCD_TDO24M
  77         tristate "Toppoly TDO24M  and TDO35S LCD Panels support"
  78         depends on SPI_MASTER
  79         help
  80           If you have a Toppoly TDO24M/TDO35S series LCD panel, say y here to
  81           include the support for it.
  82
  83 config LCD_VGG2432A4
  84         tristate "VGG2432A4 LCM device support"
  85         depends on SPI_MASTER
  86         select LCD_ILI9320
  87         help
  88           If you have a VGG2432A4 panel based on the ILI9320 controller chip
  89           then say y to include a power driver for it.
  90
  91 config LCD_PLATFORM
  92         tristate "Platform LCD controls"
  93         help
  94           This driver provides a platform-device registered LCD power
  95           control interface.
  96
  97 config LCD_TOSA
  98         tristate "Sharp SL-6000 LCD Driver"
  99         depends on I2C && SPI && MACH_TOSA
 100         help
 101           If you have an Sharp SL-6000 Zaurus say Y to enable a driver
 102           for its LCD.
 103
 104 config LCD_HP700
 105         tristate "HP Jornada 700 series LCD Driver"
 106         depends on SA1100_JORNADA720_SSP && !PREEMPT
 107         default y
 108         help
 109           If you have an HP Jornada 700 series handheld (710/720/728)
 110           say Y to enable LCD control driver.
 111
 112 config LCD_S6E63M0
 113         tristate "S6E63M0 AMOLED LCD Driver"
 114         depends on SPI && BACKLIGHT_CLASS_DEVICE
 115         default n
 116         help
 117           If you have an S6E63M0 LCD Panel, say Y to enable its
 118           LCD control driver.
 119
 120 config LCD_LD9040
 121         tristate "LD9040 AMOLED LCD Driver"
 122         depends on SPI && BACKLIGHT_CLASS_DEVICE
 123         default n
 124         help
 125           If you have an LD9040 Panel, say Y to enable its
 126           control driver.
 127
 128 config LCD_AMS369FG06
 129         tristate "AMS369FG06 AMOLED LCD Driver"
 130         depends on SPI && BACKLIGHT_CLASS_DEVICE
 131         default n
 132         help
 133           If you have an AMS369FG06 AMOLED Panel, say Y to enable its
 134           LCD control driver.
 135
 136 config LCD_LMS501KF03
 137         tristate "LMS501KF03 LCD Driver"
 138         depends on SPI
 139         default n
 140         help
 141           If you have an LMS501KF03 LCD Panel, say Y to enable its
 142           LCD control driver.
 143
 144 config LCD_HX8357
 145         tristate "Himax HX-8357 LCD Driver"
 146         depends on SPI
 147         help
 148           If you have a HX-8357 LCD panel, say Y to enable its LCD control
 149           driver.
 150
 151 endif # LCD_CLASS_DEVICE
 152
 153 #
 154 # Backlight
 155 #
 156 config BACKLIGHT_CLASS_DEVICE
 157         tristate "Lowlevel Backlight controls"
 158         default m
 159         help
 160           This framework adds support for low-level control of the LCD
 161           backlight. This includes support for brightness and power.
 162
 163           To have support for your specific LCD panel you will have to
 164           select the proper drivers which depend on this option.
 165
 166 if BACKLIGHT_CLASS_DEVICE
 167
 168 config BACKLIGHT_ATMEL_LCDC
 169         bool "Atmel LCDC Contrast-as-Backlight control"
 170         depends on FB_ATMEL
 171         default y if MACH_AT91SAM9261EK || MACH_AT91SAM9G10EK || MACH_AT91SAM9263EK
 172         help
 173           This provides a backlight control internal to the Atmel LCDC
 174           driver.  If the LCD "contrast control" on your board is wired
 175           so it controls the backlight brightness, select this option to
 176           export this as a PWM-based backlight control.
 177
 178           If in doubt, it's safe to enable this option; it doesn't kick
 179           in unless the board's description says it's wired that way.
 180
 181 config BACKLIGHT_ATMEL_PWM
 182         tristate "Atmel PWM backlight control"
 183         depends on ATMEL_PWM
 184         help
 185           Say Y here if you want to use the PWM peripheral in Atmel AT91 and
 186           AVR32 devices. This driver will need additional platform data to know
 187           which PWM instance to use and how to configure it.
 188
 189           To compile this driver as a module, choose M here: the module will be
 190           called atmel-pwm-bl.
 191
 192 config BACKLIGHT_EP93XX
 193         tristate "Cirrus EP93xx Backlight Driver"
 194         depends on FB_EP93XX
 195         help
 196           If you have a LCD backlight connected to the BRIGHT output of
 197           the EP93xx, say Y here to enable this driver.
 198
 199           To compile this driver as a module, choose M here: the module will
 200           be called ep93xx_bl.
 201
 202 config BACKLIGHT_GENERIC
 203         tristate "Generic (aka Sharp Corgi) Backlight Driver"
 204         default y
 205         help
 206           Say y to enable the generic platform backlight driver previously
 207           known as the Corgi backlight driver. If you have a Sharp Zaurus
 208           SL-C7xx, SL-Cxx00 or SL-6000x say y.
 209
 210 config BACKLIGHT_LM3533
 211         tristate "Backlight Driver for LM3533"
 212         depends on BACKLIGHT_CLASS_DEVICE
 213         depends on MFD_LM3533
 214         help
 215           Say Y to enable the backlight driver for National Semiconductor / TI
 216           LM3533 Lighting Power chips.
 217
 218           The backlights can be controlled directly, through PWM input, or by
 219           the ambient-light-sensor interface. The chip supports 256 brightness
 220           levels.
 221
 222 config BACKLIGHT_LOCOMO
 223         tristate "Sharp LOCOMO LCD/Backlight Driver"
 224         depends on SHARP_LOCOMO
 225         default y
 226         help
 227           If you have a Sharp Zaurus SL-5500 (Collie) or SL-5600 (Poodle) say y to
 228           enable the LCD/backlight driver.
 229
 230 config BACKLIGHT_OMAP1
 231         tristate "OMAP1 PWL-based LCD Backlight"
 232         depends on ARCH_OMAP1
 233         default y
 234         help
 235           This driver controls the LCD backlight level and power for
 236           the PWL module of OMAP1 processors.  Say Y if your board
 237           uses this hardware.
 238
 239 config BACKLIGHT_HP680
 240         tristate "HP Jornada 680 Backlight Driver"
 241         depends on SH_HP6XX
 242         default y
 243         help
 244           If you have a HP Jornada 680, say y to enable the
 245           backlight driver.
 246
 247 config BACKLIGHT_HP700
 248         tristate "HP Jornada 700 series Backlight Driver"
 249         depends on SA1100_JORNADA720_SSP && !PREEMPT
 250         default y
 251         help
 252           If you have an HP Jornada 700 series,
 253           say Y to include backlight control driver.
 254
 255 config BACKLIGHT_CARILLO_RANCH
 256         tristate "Intel Carillo Ranch Backlight Driver"
 257         depends on LCD_CLASS_DEVICE && PCI && X86 && FB_LE80578
 258         help
 259           If you have a Intel LE80578 (Carillo Ranch) say Y to enable the
 260           backlight driver.
 261
 262 config BACKLIGHT_PWM
 263         tristate "Generic PWM based Backlight Driver"
 264         depends on PWM
 265         help
 266           If you have a LCD backlight adjustable by PWM, say Y to enable
 267           this driver.
 268
 269 config BACKLIGHT_DA903X
 270         tristate "Backlight Driver for DA9030/DA9034 using WLED"
 271         depends on PMIC_DA903X
 272         help
 273           If you have a LCD backlight connected to the WLED output of DA9030
 274           or DA9034 WLED output, say Y here to enable this driver.
 275
 276 config BACKLIGHT_DA9052
 277         tristate "Dialog DA9052/DA9053 WLED"
 278         depends on PMIC_DA9052
 279         help
 280           Enable the Backlight Driver for DA9052-BC and DA9053-AA/Bx PMICs.
 281
 282 config BACKLIGHT_MAX8925
 283         tristate "Backlight driver for MAX8925"
 284         depends on MFD_MAX8925
 285         help
 286           If you have a LCD backlight connected to the WLED output of MAX8925
 287           WLED output, say Y here to enable this driver.
 288
 289 config BACKLIGHT_APPLE
 290        tristate "Apple Backlight Driver"
 291        depends on X86 && ACPI
 292        help
 293          If you have an Intel-based Apple say Y to enable a driver for its
 294          backlight.
 295
 296 config BACKLIGHT_TOSA
 297         tristate "Sharp SL-6000 Backlight Driver"
 298         depends on I2C && MACH_TOSA && LCD_TOSA
 299         help
 300           If you have an Sharp SL-6000 Zaurus say Y to enable a driver
 301           for its backlight
 302
 303 config BACKLIGHT_SAHARA
 304         tristate "Tabletkiosk Sahara Touch-iT Backlight Driver"
 305         depends on X86
 306         help
 307           If you have a Tabletkiosk Sahara Touch-iT, say y to enable the
 308           backlight driver.
 309
 310 config BACKLIGHT_WM831X
 311         tristate "WM831x PMIC Backlight Driver"
 312         depends on MFD_WM831X
 313         help
 314           If you have a backlight driven by the ISINK and DCDC of a
 315           WM831x PMIC say y to enable the backlight driver for it.
 316
 317 config BACKLIGHT_ADP5520
 318         tristate "Backlight Driver for ADP5520/ADP5501 using WLED"
 319         depends on PMIC_ADP5520
 320         help
 321           If you have a LCD backlight connected to the BST/BL_SNK output of
 322           ADP5520 or ADP5501, say Y here to enable this driver.
 323
 324           To compile this driver as a module, choose M here: the module will
 325           be called adp5520_bl.
 326
 327 config BACKLIGHT_ADP8860
 328         tristate "Backlight Driver for ADP8860/ADP8861/ADP8863 using WLED"
 329         depends on BACKLIGHT_CLASS_DEVICE && I2C
 330         select NEW_LEDS
 331         select LEDS_CLASS
 332         help
 333           If you have a LCD backlight connected to the ADP8860, ADP8861 or
 334           ADP8863 say Y here to enable this driver.
 335
 336           To compile this driver as a module, choose M here: the module will
 337           be called adp8860_bl.
 338
 339 config BACKLIGHT_ADP8870
 340         tristate "Backlight Driver for ADP8870 using WLED"
 341         depends on BACKLIGHT_CLASS_DEVICE && I2C
 342         select NEW_LEDS
 343         select LEDS_CLASS
 344         help
 345           If you have a LCD backlight connected to the ADP8870,
 346           say Y here to enable this driver.
 347
 348           To compile this driver as a module, choose M here: the module will
 349           be called adp8870_bl.
 350
 351 config BACKLIGHT_88PM860X
 352         tristate "Backlight Driver for 88PM8606 using WLED"
 353         depends on MFD_88PM860X
 354         help
 355           Say Y to enable the backlight driver for Marvell 88PM8606.
 356
 357 config BACKLIGHT_PCF50633
 358         tristate "Backlight driver for NXP PCF50633 MFD"
 359         depends on BACKLIGHT_CLASS_DEVICE && MFD_PCF50633
 360         help
 361           If you have a backlight driven by a NXP PCF50633 MFD, say Y here to
 362           enable its driver.
 363
 364 config BACKLIGHT_AAT2870
 365         tristate "AnalogicTech AAT2870 Backlight"
 366         depends on BACKLIGHT_CLASS_DEVICE && MFD_AAT2870_CORE
 367         help
 368           If you have a AnalogicTech AAT2870 say Y to enable the
 369           backlight driver.
 370
 371 config BACKLIGHT_LM3630
 372         tristate "Backlight Driver for LM3630"
 373         depends on BACKLIGHT_CLASS_DEVICE && I2C
 374         select REGMAP_I2C
 375         help
 376           This supports TI LM3630 Backlight Driver
 377
 378 config BACKLIGHT_LM3639
 379         tristate "Backlight Driver for LM3639"
 380         depends on BACKLIGHT_CLASS_DEVICE && I2C
 381         select REGMAP_I2C
 382         select NEW_LEDS
 383         select LEDS_CLASS
 384         help
 385           This supports TI LM3639 Backlight + 1.5A Flash LED Driver
 386
 387 config BACKLIGHT_LP855X
 388         tristate "Backlight driver for TI LP855X"
 389         depends on BACKLIGHT_CLASS_DEVICE && I2C
 390         help
 391           This supports TI LP8550, LP8551, LP8552, LP8553, LP8556 and LP8557
 392           backlight driver.
 393
 394 config BACKLIGHT_LP8788
 395         tristate "Backlight driver for TI LP8788 MFD"
 396         depends on BACKLIGHT_CLASS_DEVICE && MFD_LP8788
 397         help
 398           This supports TI LP8788 backlight driver.
 399
 400 config BACKLIGHT_OT200
 401         tristate "Backlight driver for ot200 visualisation device"
 402         depends on BACKLIGHT_CLASS_DEVICE && CS5535_MFGPT && GPIO_CS5535
 403         help
 404           To compile this driver as a module, choose M here: the module will be
 405           called ot200_bl.
 406
 407 config BACKLIGHT_PANDORA
 408         tristate "Backlight driver for Pandora console"
 409         depends on TWL4030_CORE
 410         help
 411           If you have a Pandora console, say Y to enable the
 412           backlight driver.
 413
 414 config BACKLIGHT_TPS65217
 415         tristate "TPS65217 Backlight"
 416         depends on BACKLIGHT_CLASS_DEVICE && MFD_TPS65217
 417         help
 418           If you have a Texas Instruments TPS65217 say Y to enable the
 419           backlight driver.
 420
 421 config BACKLIGHT_AS3711
 422         tristate "AS3711 Backlight"
 423         depends on BACKLIGHT_CLASS_DEVICE && MFD_AS3711
 424         help
 425           If you have an Austrian Microsystems AS3711 say Y to enable the
 426           backlight driver.
 427
 428 endif # BACKLIGHT_CLASS_DEVICE
 429
 430 endif # BACKLIGHT_LCD_SUPPORT