drivers/video/backlight/Kconfig

   1 #
   2 # Backlight & LCD drivers configuration
   3 #
   4
   5 menuconfig BACKLIGHT_LCD_SUPPORT
   6         bool "Backlight & LCD device support"
   7         help
   8           Enable this to be able to choose the drivers for controlling the
   9           backlight and the LCD panel on some platforms, for example on PDAs.
  10
  11 if BACKLIGHT_LCD_SUPPORT
  12
  13 #
  14 # LCD
  15 #
  16 config LCD_CLASS_DEVICE
  17         tristate "Lowlevel LCD controls"
  18         default m
  19         help
  20           This framework adds support for low-level control of LCD.
  21           Some framebuffer devices connect to platform-specific LCD modules
  22           in order to have a platform-specific way to control the flat panel
  23           (contrast and applying power to the LCD (not to the backlight!)).
  24
  25           To have support for your specific LCD panel you will have to
  26           select the proper drivers which depend on this option.
  27
  28 if LCD_CLASS_DEVICE
  29
  30 config LCD_CORGI
  31         tristate "LCD Panel support for SHARP corgi/spitz model"
  32         depends on SPI_MASTER && PXA_SHARPSL
  33         help
  34           Say y here to support the LCD panels usually found on SHARP
  35           corgi (C7x0) and spitz (Cxx00) models.
  36
  37 config LCD_L4F00242T03
  38         tristate "Epson L4F00242T03 LCD"
  39         depends on SPI_MASTER && GENERIC_GPIO
  40         help
  41           SPI driver for Epson L4F00242T03. This provides basic support
  42           for init and powering the LCD up/down through a sysfs interface.
  43
  44 config LCD_LMS283GF05
  45         tristate "Samsung LMS283GF05 LCD"
  46         depends on SPI_MASTER && GENERIC_GPIO
  47         help
  48           SPI driver for Samsung LMS283GF05. This provides basic support
  49           for powering the LCD up/down through a sysfs interface.
  50
  51 config LCD_LTV350QV
  52         tristate "Samsung LTV350QV LCD Panel"
  53         depends on SPI_MASTER
  54         help
  55           If you have a Samsung LTV350QV LCD panel, say y to include a
  56           power control driver for it.  The panel starts up in power
  57           off state, so you need this driver in order to see any
  58           output.
  59
  60           The LTV350QV panel is present on all ATSTK1000 boards.
  61
  62 config LCD_ILI9320
  63         tristate "ILI Technology ILI9320 controller support"
  64         depends on SPI
  65         help
  66           If you have a panel based on the ILI9320 controller chip
  67           then say y to include a power driver for it.
  68
  69 config LCD_TDO24M
  70         tristate "Toppoly TDO24M  and TDO35S LCD Panels support"
  71         depends on SPI_MASTER
  72         help
  73           If you have a Toppoly TDO24M/TDO35S series LCD panel, say y here to
  74           include the support for it.
  75
  76 config LCD_VGG2432A4
  77         tristate "VGG2432A4 LCM device support"
  78         depends on SPI_MASTER
  79         select LCD_ILI9320
  80         help
  81           If you have a VGG2432A4 panel based on the ILI9320 controller chip
  82           then say y to include a power driver for it.
  83
  84 config LCD_PLATFORM
  85         tristate "Platform LCD controls"
  86         help
  87           This driver provides a platform-device registered LCD power
  88           control interface.
  89
  90 config LCD_TOSA
  91         tristate "Sharp SL-6000 LCD Driver"
  92         depends on I2C && SPI && MACH_TOSA
  93         help
  94           If you have an Sharp SL-6000 Zaurus say Y to enable a driver
  95           for its LCD.
  96
  97 config LCD_HP700
  98         tristate "HP Jornada 700 series LCD Driver"
  99         depends on SA1100_JORNADA720_SSP && !PREEMPT
 100         default y
 101         help
 102           If you have an HP Jornada 700 series handheld (710/720/728)
 103           say Y to enable LCD control driver.
 104
 105 config LCD_S6E63M0
 106         tristate "S6E63M0 AMOLED LCD Driver"
 107         depends on SPI && BACKLIGHT_CLASS_DEVICE
 108         default n
 109         help
 110           If you have an S6E63M0 LCD Panel, say Y to enable its
 111           LCD control driver.
 112
 113 config LCD_LD9040
 114         tristate "LD9040 AMOLED LCD Driver"
 115         depends on SPI && BACKLIGHT_CLASS_DEVICE
 116         default n
 117         help
 118           If you have an LD9040 Panel, say Y to enable its
 119           control driver.
 120
 121 config LCD_AMS369FG06
 122         tristate "AMS369FG06 AMOLED LCD Driver"
 123         depends on SPI && BACKLIGHT_CLASS_DEVICE
 124         default n
 125         help
 126           If you have an AMS369FG06 AMOLED Panel, say Y to enable its
 127           LCD control driver.
 128
 129 endif # LCD_CLASS_DEVICE
 130
 131 #
 132 # Backlight
 133 #
 134 config BACKLIGHT_CLASS_DEVICE
 135         tristate "Lowlevel Backlight controls"
 136         default m
 137         help
 138           This framework adds support for low-level control of the LCD
 139           backlight. This includes support for brightness and power.
 140
 141           To have support for your specific LCD panel you will have to
 142           select the proper drivers which depend on this option.
 143
 144 if BACKLIGHT_CLASS_DEVICE
 145
 146 config BACKLIGHT_ATMEL_LCDC
 147         bool "Atmel LCDC Contrast-as-Backlight control"
 148         depends on FB_ATMEL
 149         default y if MACH_SAM9261EK || MACH_SAM9G10EK || MACH_SAM9263EK
 150         help
 151           This provides a backlight control internal to the Atmel LCDC
 152           driver.  If the LCD "contrast control" on your board is wired
 153           so it controls the backlight brightness, select this option to
 154           export this as a PWM-based backlight control.
 155
 156           If in doubt, it's safe to enable this option; it doesn't kick
 157           in unless the board's description says it's wired that way.
 158
 159 config BACKLIGHT_ATMEL_PWM
 160         tristate "Atmel PWM backlight control"
 161         depends on ATMEL_PWM
 162         help
 163           Say Y here if you want to use the PWM peripheral in Atmel AT91 and
 164           AVR32 devices. This driver will need additional platform data to know
 165           which PWM instance to use and how to configure it.
 166
 167           To compile this driver as a module, choose M here: the module will be
 168           called atmel-pwm-bl.
 169
 170 config BACKLIGHT_EP93XX
 171         tristate "Cirrus EP93xx Backlight Driver"
 172         depends on FB_EP93XX
 173         help
 174           If you have a LCD backlight connected to the BRIGHT output of
 175           the EP93xx, say Y here to enable this driver.
 176
 177           To compile this driver as a module, choose M here: the module will
 178           be called ep93xx_bl.
 179
 180 config BACKLIGHT_GENERIC
 181         tristate "Generic (aka Sharp Corgi) Backlight Driver"
 182         default y
 183         help
 184           Say y to enable the generic platform backlight driver previously
 185           known as the Corgi backlight driver. If you have a Sharp Zaurus
 186           SL-C7xx, SL-Cxx00 or SL-6000x say y.
 187
 188 config BACKLIGHT_LM3533
 189         tristate "Backlight Driver for LM3533"
 190         depends on BACKLIGHT_CLASS_DEVICE
 191         depends on MFD_LM3533
 192         help
 193           Say Y to enable the backlight driver for National Semiconductor / TI
 194           LM3533 Lighting Power chips.
 195
 196           The backlights can be controlled directly, through PWM input, or by
 197           the ambient-light-sensor interface. The chip supports 256 brightness
 198           levels.
 199
 200 config BACKLIGHT_LOCOMO
 201         tristate "Sharp LOCOMO LCD/Backlight Driver"
 202         depends on SHARP_LOCOMO
 203         default y
 204         help
 205           If you have a Sharp Zaurus SL-5500 (Collie) or SL-5600 (Poodle) say y to
 206           enable the LCD/backlight driver.
 207
 208 config BACKLIGHT_OMAP1
 209         tristate "OMAP1 PWL-based LCD Backlight"
 210         depends on ARCH_OMAP1
 211         default y
 212         help
 213           This driver controls the LCD backlight level and power for
 214           the PWL module of OMAP1 processors.  Say Y if your board
 215           uses this hardware.
 216
 217 config BACKLIGHT_HP680
 218         tristate "HP Jornada 680 Backlight Driver"
 219         depends on SH_HP6XX
 220         default y
 221         help
 222           If you have a HP Jornada 680, say y to enable the
 223           backlight driver.
 224
 225 config BACKLIGHT_HP700
 226         tristate "HP Jornada 700 series Backlight Driver"
 227         depends on SA1100_JORNADA720_SSP && !PREEMPT
 228         default y
 229         help
 230           If you have an HP Jornada 700 series,
 231           say Y to include backlight control driver.
 232
 233 config BACKLIGHT_CARILLO_RANCH
 234         tristate "Intel Carillo Ranch Backlight Driver"
 235         depends on LCD_CLASS_DEVICE && PCI && X86 && FB_LE80578
 236         help
 237           If you have a Intel LE80578 (Carillo Ranch) say Y to enable the
 238           backlight driver.
 239
 240 config BACKLIGHT_PWM
 241         tristate "Generic PWM based Backlight Driver"
 242         depends on PWM
 243         help
 244           If you have a LCD backlight adjustable by PWM, say Y to enable
 245           this driver.
 246
 247 config BACKLIGHT_DA903X
 248         tristate "Backlight Driver for DA9030/DA9034 using WLED"
 249         depends on PMIC_DA903X
 250         help
 251           If you have a LCD backlight connected to the WLED output of DA9030
 252           or DA9034 WLED output, say Y here to enable this driver.
 253
 254 config BACKLIGHT_DA9052
 255         tristate "Dialog DA9052/DA9053 WLED"
 256         depends on PMIC_DA9052
 257         help
 258           Enable the Backlight Driver for DA9052-BC and DA9053-AA/Bx PMICs.
 259
 260 config BACKLIGHT_MAX8925
 261         tristate "Backlight driver for MAX8925"
 262         depends on MFD_MAX8925
 263         help
 264           If you have a LCD backlight connected to the WLED output of MAX8925
 265           WLED output, say Y here to enable this driver.
 266
 267 config BACKLIGHT_APPLE
 268        tristate "Apple Backlight Driver"
 269        depends on X86 && ACPI
 270        help
 271          If you have an Intel-based Apple say Y to enable a driver for its
 272          backlight.
 273
 274 config BACKLIGHT_TOSA
 275         tristate "Sharp SL-6000 Backlight Driver"
 276         depends on I2C && MACH_TOSA && LCD_TOSA
 277         help
 278           If you have an Sharp SL-6000 Zaurus say Y to enable a driver
 279           for its backlight
 280
 281 config BACKLIGHT_SAHARA
 282         tristate "Tabletkiosk Sahara Touch-iT Backlight Driver"
 283         depends on X86
 284         help
 285           If you have a Tabletkiosk Sahara Touch-iT, say y to enable the
 286           backlight driver.
 287
 288 config BACKLIGHT_WM831X
 289         tristate "WM831x PMIC Backlight Driver"
 290         depends on MFD_WM831X
 291         help
 292           If you have a backlight driven by the ISINK and DCDC of a
 293           WM831x PMIC say y to enable the backlight driver for it.
 294
 295 config BACKLIGHT_ADP5520
 296         tristate "Backlight Driver for ADP5520/ADP5501 using WLED"
 297         depends on PMIC_ADP5520
 298         help
 299           If you have a LCD backlight connected to the BST/BL_SNK output of
 300           ADP5520 or ADP5501, say Y here to enable this driver.
 301
 302           To compile this driver as a module, choose M here: the module will
 303           be called adp5520_bl.
 304
 305 config BACKLIGHT_ADP8860
 306         tristate "Backlight Driver for ADP8860/ADP8861/ADP8863 using WLED"
 307         depends on BACKLIGHT_CLASS_DEVICE && I2C
 308         select NEW_LEDS
 309         select LEDS_CLASS
 310         help
 311           If you have a LCD backlight connected to the ADP8860, ADP8861 or
 312           ADP8863 say Y here to enable this driver.
 313
 314           To compile this driver as a module, choose M here: the module will
 315           be called adp8860_bl.
 316
 317 config BACKLIGHT_ADP8870
 318         tristate "Backlight Driver for ADP8870 using WLED"
 319         depends on BACKLIGHT_CLASS_DEVICE && I2C
 320         select NEW_LEDS
 321         select LEDS_CLASS
 322         help
 323           If you have a LCD backlight connected to the ADP8870,
 324           say Y here to enable this driver.
 325
 326           To compile this driver as a module, choose M here: the module will
 327           be called adp8870_bl.
 328
 329 config BACKLIGHT_88PM860X
 330         tristate "Backlight Driver for 88PM8606 using WLED"
 331         depends on MFD_88PM860X
 332         help
 333           Say Y to enable the backlight driver for Marvell 88PM8606.
 334
 335 config BACKLIGHT_PCF50633
 336         tristate "Backlight driver for NXP PCF50633 MFD"
 337         depends on BACKLIGHT_CLASS_DEVICE && MFD_PCF50633
 338         help
 339           If you have a backlight driven by a NXP PCF50633 MFD, say Y here to
 340           enable its driver.
 341
 342 config BACKLIGHT_AAT2870
 343         tristate "AnalogicTech AAT2870 Backlight"
 344         depends on BACKLIGHT_CLASS_DEVICE && MFD_AAT2870_CORE
 345         help
 346           If you have a AnalogicTech AAT2870 say Y to enable the
 347           backlight driver.
 348
 349 config BACKLIGHT_LM3630
 350         tristate "Backlight Driver for LM3630"
 351         depends on BACKLIGHT_CLASS_DEVICE && I2C
 352         select REGMAP_I2C
 353         help
 354           This supports TI LM3630 Backlight Driver
 355
 356 config BACKLIGHT_LM3639
 357         tristate "Backlight Driver for LM3639"
 358         depends on BACKLIGHT_CLASS_DEVICE && I2C
 359         select REGMAP_I2C
 360         select NEW_LEDS
 361         select LEDS_CLASS
 362         help
 363           This supports TI LM3639 Backlight + 1.5A Flash LED Driver
 364
 365 config BACKLIGHT_LP855X
 366         tristate "Backlight driver for TI LP855X"
 367         depends on BACKLIGHT_CLASS_DEVICE && I2C
 368         help
 369           This supports TI LP8550, LP8551, LP8552, LP8553 and LP8556
 370           backlight driver.
 371
 372 config BACKLIGHT_OT200
 373         tristate "Backlight driver for ot200 visualisation device"
 374         depends on BACKLIGHT_CLASS_DEVICE && CS5535_MFGPT && GPIO_CS5535
 375         help
 376           To compile this driver as a module, choose M here: the module will be
 377           called ot200_bl.
 378
 379 config BACKLIGHT_PANDORA
 380         tristate "Backlight driver for Pandora console"
 381         depends on TWL4030_CORE
 382         help
 383           If you have a Pandora console, say Y to enable the
 384           backlight driver.
 385
 386 config BACKLIGHT_TPS65217
 387         tristate "TPS65217 Backlight"
 388         depends on BACKLIGHT_CLASS_DEVICE && MFD_TPS65217
 389         help
 390           If you have a Texas Instruments TPS65217 say Y to enable the
 391           backlight driver.
 392
 393 endif # BACKLIGHT_CLASS_DEVICE
 394
 395 endif # BACKLIGHT_LCD_SUPPORT