drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         boolean "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       boolean "SPI Master Support"
  44         boolean
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ALTERA
  57         tristate "Altera SPI Controller"
  58         select SPI_BITBANG
  59         help
  60           This is the driver for the Altera SPI Controller.
  61
  62 config SPI_ATH79
  63         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  64         depends on ATH79 && GENERIC_GPIO
  65         select SPI_BITBANG
  66         help
  67           This enables support for the SPI controller present on the
  68           Atheros AR71XX/AR724X/AR913X SoCs.
  69
  70 config SPI_ATMEL
  71         tristate "Atmel SPI Controller"
  72         depends on (ARCH_AT91 || AVR32)
  73         help
  74           This selects a driver for the Atmel SPI Controller, present on
  75           many AT32 (AVR32) and AT91 (ARM) chips.
  76
  77 config SPI_BFIN5XX
  78         tristate "SPI controller driver for ADI Blackfin5xx"
  79         depends on BLACKFIN
  80         help
  81           This is the SPI controller master driver for Blackfin 5xx processor.
  82
  83 config SPI_BFIN_SPORT
  84         tristate "SPI bus via Blackfin SPORT"
  85         depends on BLACKFIN
  86         help
  87           Enable support for a SPI bus via the Blackfin SPORT peripheral.
  88
  89 config SPI_AU1550
  90         tristate "Au1550/Au1200/Au1300 SPI Controller"
  91         depends on MIPS_ALCHEMY && EXPERIMENTAL
  92         select SPI_BITBANG
  93         help
  94           If you say yes to this option, support will be included for the
  95           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
  96
  97 config SPI_BCM63XX
  98         tristate "Broadcom BCM63xx SPI controller"
  99         depends on BCM63XX
 100         help
 101           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 102
 103 config SPI_BITBANG
 104         tristate "Utilities for Bitbanging SPI masters"
 105         help
 106           With a few GPIO pins, your system can bitbang the SPI protocol.
 107           Select this to get SPI support through I/O pins (GPIO, parallel
 108           port, etc).  Or, some systems' SPI master controller drivers use
 109           this code to manage the per-word or per-transfer accesses to the
 110           hardware shift registers.
 111
 112           This is library code, and is automatically selected by drivers that
 113           need it.  You only need to select this explicitly to support driver
 114           modules that aren't part of this kernel tree.
 115
 116 config SPI_BUTTERFLY
 117         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 118         depends on PARPORT
 119         select SPI_BITBANG
 120         help
 121           This uses a custom parallel port cable to connect to an AVR
 122           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 123           inexpensive battery powered microcontroller evaluation board.
 124           This same cable can be used to flash new firmware.
 125
 126 config SPI_COLDFIRE_QSPI
 127         tristate "Freescale Coldfire QSPI controller"
 128         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 129         help
 130           This enables support for the Coldfire QSPI controller in master
 131           mode.
 132
 133 config SPI_DAVINCI
 134         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 135         depends on ARCH_DAVINCI
 136         select SPI_BITBANG
 137         help
 138           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 139
 140 config SPI_EP93XX
 141         tristate "Cirrus Logic EP93xx SPI controller"
 142         depends on ARCH_EP93XX
 143         help
 144           This enables using the Cirrus EP93xx SPI controller in master
 145           mode.
 146
 147 config SPI_FALCON
 148         tristate "Falcon SPI controller support"
 149         depends on SOC_FALCON
 150         help
 151           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 152           emulation that is designed for serial flash access. This driver
 153           has only been tested with m25p80 type chips. The hardware has no
 154           support for other types of SPI peripherals.
 155
 156 config SPI_GPIO
 157         tristate "GPIO-based bitbanging SPI Master"
 158         depends on GENERIC_GPIO
 159         select SPI_BITBANG
 160         help
 161           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 162           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 163           slaves connected to a bus using this driver are configured as usual,
 164           except that the spi_board_info.controller_data holds the GPIO number
 165           for the chipselect used by this controller driver.
 166
 167           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 168           making it unusually slow for SPI.  If your platform can inline
 169           GPIO operations, you should be able to leverage that for better
 170           speed with a custom version of this driver; see the source code.
 171
 172 config SPI_IMX
 173         tristate "Freescale i.MX SPI controllers"
 174         depends on ARCH_MXC
 175         select SPI_BITBANG
 176         default m if IMX_HAVE_PLATFORM_SPI_IMX
 177         help
 178           This enables using the Freescale i.MX SPI controllers in master
 179           mode.
 180
 181 config SPI_LM70_LLP
 182         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 183         depends on PARPORT && EXPERIMENTAL
 184         select SPI_BITBANG
 185         help
 186           This driver supports the NS LM70 LLP Evaluation Board,
 187           which interfaces to an LM70 temperature sensor using
 188           a parallel port.
 189
 190 config SPI_MPC52xx
 191         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 192         depends on PPC_MPC52xx
 193         help
 194           This drivers supports the MPC52xx SPI controller in master SPI
 195           mode.
 196
 197 config SPI_MPC52xx_PSC
 198         tristate "Freescale MPC52xx PSC SPI controller"
 199         depends on PPC_MPC52xx && EXPERIMENTAL
 200         help
 201           This enables using the Freescale MPC52xx Programmable Serial
 202           Controller in master SPI mode.
 203
 204 config SPI_MPC512x_PSC
 205         tristate "Freescale MPC512x PSC SPI controller"
 206         depends on PPC_MPC512x
 207         help
 208           This enables using the Freescale MPC5121 Programmable Serial
 209           Controller in SPI master mode.
 210
 211 config SPI_FSL_LIB
 212         tristate
 213         depends on FSL_SOC
 214
 215 config SPI_FSL_SPI
 216         bool "Freescale SPI controller"
 217         depends on FSL_SOC
 218         select SPI_FSL_LIB
 219         help
 220           This enables using the Freescale SPI controllers in master mode.
 221           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 222           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 223
 224 config SPI_FSL_ESPI
 225         bool "Freescale eSPI controller"
 226         depends on FSL_SOC
 227         select SPI_FSL_LIB
 228         help
 229           This enables using the Freescale eSPI controllers in master mode.
 230           From MPC8536, 85xx platform uses the controller, and all P10xx,
 231           P20xx, P30xx,P40xx, P50xx uses this controller.
 232
 233 config SPI_OC_TINY
 234         tristate "OpenCores tiny SPI"
 235         depends on GENERIC_GPIO
 236         select SPI_BITBANG
 237         help
 238           This is the driver for OpenCores tiny SPI master controller.
 239
 240 config SPI_OMAP_UWIRE
 241         tristate "OMAP1 MicroWire"
 242         depends on ARCH_OMAP1
 243         select SPI_BITBANG
 244         help
 245           This hooks up to the MicroWire controller on OMAP1 chips.
 246
 247 config SPI_OMAP24XX
 248         tristate "McSPI driver for OMAP"
 249         depends on ARCH_OMAP2PLUS
 250         help
 251           SPI master controller for OMAP24XX and later Multichannel SPI
 252           (McSPI) modules.
 253
 254 config SPI_OMAP_100K
 255         tristate "OMAP SPI 100K"
 256         depends on ARCH_OMAP850 || ARCH_OMAP730
 257         help
 258           OMAP SPI 100K master controller for omap7xx boards.
 259
 260 config SPI_ORION
 261         tristate "Orion SPI master (EXPERIMENTAL)"
 262         depends on PLAT_ORION && EXPERIMENTAL
 263         help
 264           This enables using the SPI master controller on the Orion chips.
 265
 266 config SPI_PL022
 267         tristate "ARM AMBA PL022 SSP controller"
 268         depends on ARM_AMBA
 269         default y if MACH_U300
 270         default y if ARCH_REALVIEW
 271         default y if INTEGRATOR_IMPD1
 272         default y if ARCH_VERSATILE
 273         help
 274           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 275           controller. If you have an embedded system with an AMBA(R)
 276           bus and a PL022 controller, say Y or M here.
 277
 278 config SPI_PPC4xx
 279         tristate "PPC4xx SPI Controller"
 280         depends on PPC32 && 4xx
 281         select SPI_BITBANG
 282         help
 283           This selects a driver for the PPC4xx SPI Controller.
 284
 285 config SPI_PXA2XX
 286         tristate "PXA2xx SSP SPI master"
 287         depends on (ARCH_PXA || (X86_32 && PCI)) && EXPERIMENTAL
 288         select PXA_SSP if ARCH_PXA
 289         help
 290           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 291           controller. The driver can be configured to use any SSP port and
 292           additional documentation can be found a Documentation/spi/pxa2xx.
 293
 294 config SPI_PXA2XX_PCI
 295         def_bool SPI_PXA2XX && X86_32 && PCI
 296
 297 config SPI_RSPI
 298         tristate "Renesas RSPI controller"
 299         depends on SUPERH
 300         help
 301           SPI driver for Renesas RSPI blocks.
 302
 303 config SPI_S3C24XX
 304         tristate "Samsung S3C24XX series SPI"
 305         depends on ARCH_S3C24XX && EXPERIMENTAL
 306         select SPI_BITBANG
 307         help
 308           SPI driver for Samsung S3C24XX series ARM SoCs
 309
 310 config SPI_S3C24XX_FIQ
 311         bool "S3C24XX driver with FIQ pseudo-DMA"
 312         depends on SPI_S3C24XX
 313         select FIQ
 314         help
 315           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 316           DMA by using the fast-interrupt request framework, This allows
 317           the driver to get DMA-like performance when there are either
 318           no free DMA channels, or when doing transfers that required both
 319           TX and RX data paths.
 320
 321 config SPI_S3C64XX
 322         tristate "Samsung S3C64XX series type SPI"
 323         depends on (ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5P64X0 || ARCH_EXYNOS)
 324         select S3C64XX_DMA if ARCH_S3C64XX
 325         help
 326           SPI driver for Samsung S3C64XX and newer SoCs.
 327
 328 config SPI_SC18IS602
 329         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 330         depends on I2C
 331         help
 332           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 333
 334 config SPI_SH_MSIOF
 335         tristate "SuperH MSIOF SPI controller"
 336         depends on SUPERH && HAVE_CLK
 337         select SPI_BITBANG
 338         help
 339           SPI driver for SuperH MSIOF blocks.
 340
 341 config SPI_SH
 342         tristate "SuperH SPI controller"
 343         depends on SUPERH
 344         help
 345           SPI driver for SuperH SPI blocks.
 346
 347 config SPI_SH_SCI
 348         tristate "SuperH SCI SPI controller"
 349         depends on SUPERH
 350         select SPI_BITBANG
 351         help
 352           SPI driver for SuperH SCI blocks.
 353
 354 config SPI_SH_HSPI
 355         tristate "SuperH HSPI controller"
 356         depends on ARCH_SHMOBILE
 357         help
 358           SPI driver for SuperH HSPI blocks.
 359
 360 config SPI_SIRF
 361         tristate "CSR SiRFprimaII SPI controller"
 362         depends on ARCH_PRIMA2
 363         select SPI_BITBANG
 364         help
 365           SPI driver for CSR SiRFprimaII SoCs
 366
 367 config SPI_STMP3XXX
 368         tristate "Freescale STMP37xx/378x SPI/SSP controller"
 369         depends on ARCH_STMP3XXX
 370         help
 371           SPI driver for Freescale STMP37xx/378x SoC SSP interface
 372
 373 config SPI_MXS
 374         tristate "Freescale MXS SPI controller"
 375         depends on ARCH_MXS
 376         select STMP_DEVICE
 377         help
 378           SPI driver for Freescale MXS devices.
 379
 380 config SPI_TI_SSP
 381         tristate "TI Sequencer Serial Port - SPI Support"
 382         depends on MFD_TI_SSP
 383         help
 384           This selects an SPI master implementation using a TI sequencer
 385           serial port.
 386
 387 config SPI_TOPCLIFF_PCH
 388         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
 389         depends on PCI
 390         help
 391           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 392           used in some x86 embedded processors.
 393
 394           This driver also supports the ML7213/ML7223/ML7831, a companion chip
 395           for the Atom E6xx series and compatible with the Intel EG20T PCH.
 396
 397 config SPI_TXX9
 398         tristate "Toshiba TXx9 SPI controller"
 399         depends on GENERIC_GPIO && CPU_TX49XX
 400         help
 401           SPI driver for Toshiba TXx9 MIPS SoCs
 402
 403 config SPI_XCOMM
 404         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
 405         depends on I2C
 406         help
 407           Support for the SPI-I2C bridge found on the Analog Devices
 408           AD-FMCOMMS1-EBZ board.
 409
 410 config SPI_XILINX
 411         tristate "Xilinx SPI controller common module"
 412         depends on HAS_IOMEM && EXPERIMENTAL
 413         select SPI_BITBANG
 414         help
 415           This exposes the SPI controller IP from the Xilinx EDK.
 416
 417           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 418           Product Specification document (DS464) for hardware details.
 419
 420           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 421
 422 config SPI_NUC900
 423         tristate "Nuvoton NUC900 series SPI"
 424         depends on ARCH_W90X900 && EXPERIMENTAL
 425         select SPI_BITBANG
 426         help
 427           SPI driver for Nuvoton NUC900 series ARM SoCs
 428
 429 #
 430 # Add new SPI master controllers in alphabetical order above this line
 431 #
 432
 433 config SPI_DESIGNWARE
 434         tristate "DesignWare SPI controller core support"
 435         help
 436           general driver for SPI controller core from DesignWare
 437
 438 config SPI_DW_PCI
 439         tristate "PCI interface driver for DW SPI core"
 440         depends on SPI_DESIGNWARE && PCI
 441
 442 config SPI_DW_MID_DMA
 443         bool "DMA support for DW SPI controller on Intel Moorestown platform"
 444         depends on SPI_DW_PCI && INTEL_MID_DMAC
 445
 446 config SPI_DW_MMIO
 447         tristate "Memory-mapped io interface driver for DW SPI core"
 448         depends on SPI_DESIGNWARE && HAVE_CLK
 449
 450 #
 451 # There are lots of SPI device types, with sensors and memory
 452 # being probably the most widely used ones.
 453 #
 454 comment "SPI Protocol Masters"
 455
 456 config SPI_SPIDEV
 457         tristate "User mode SPI device driver support"
 458         depends on EXPERIMENTAL
 459         help
 460           This supports user mode SPI protocol drivers.
 461
 462           Note that this application programming interface is EXPERIMENTAL
 463           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 464
 465 config SPI_TLE62X0
 466         tristate "Infineon TLE62X0 (for power switching)"
 467         depends on SYSFS
 468         help
 469           SPI driver for Infineon TLE62X0 series line driver chips,
 470           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 471           sysfs interface, with each line presented as a kind of GPIO
 472           exposing both switch control and diagnostic feedback.
 473
 474 #
 475 # Add new SPI protocol masters in alphabetical order above this line
 476 #
 477
 478 endif # SPI_MASTER
 479
 480 # (slave support would go here)
 481
 482 endif # SPI