drivers/spi/Kconfig

   1 #
   2 # SPI driver configuration
   3 #
   4 # NOTE:  the reason this doesn't show SPI slave support is mostly that
   5 # nobody's needed a slave side API yet.  The master-role API is not
   6 # fully appropriate there, so it'd need some thought to do well.
   7 #
   8 menuconfig SPI
   9         bool "SPI support"
  10         depends on HAS_IOMEM
  11         help
  12           The "Serial Peripheral Interface" is a low level synchronous
  13           protocol.  Chips that support SPI can have data transfer rates
  14           up to several tens of Mbit/sec.  Chips are addressed with a
  15           controller and a chipselect.  Most SPI slaves don't support
  16           dynamic device discovery; some are even write-only or read-only.
  17
  18           SPI is widely used by microcontrollers to talk with sensors,
  19           eeprom and flash memory, codecs and various other controller
  20           chips, analog to digital (and d-to-a) converters, and more.
  21           MMC and SD cards can be accessed using SPI protocol; and for
  22           DataFlash cards used in MMC sockets, SPI must always be used.
  23
  24           SPI is one of a family of similar protocols using a four wire
  25           interface (select, clock, data in, data out) including Microwire
  26           (half duplex), SSP, SSI, and PSP.  This driver framework should
  27           work with most such devices and controllers.
  28
  29 if SPI
  30
  31 config SPI_DEBUG
  32         boolean "Debug support for SPI drivers"
  33         depends on DEBUG_KERNEL
  34         help
  35           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  36           sysfs, and debugfs support in SPI controller and protocol drivers.
  37
  38 #
  39 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  40 #
  41
  42 config SPI_MASTER
  43 #       boolean "SPI Master Support"
  44         boolean
  45         default SPI
  46         help
  47           If your system has an master-capable SPI controller (which
  48           provides the clock and chipselect), you can enable that
  49           controller and the protocol drivers for the SPI slave chips
  50           that are connected.
  51
  52 if SPI_MASTER
  53
  54 comment "SPI Master Controller Drivers"
  55
  56 config SPI_ALTERA
  57         tristate "Altera SPI Controller"
  58         select SPI_BITBANG
  59         help
  60           This is the driver for the Altera SPI Controller.
  61
  62 config SPI_ATH79
  63         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  64         depends on ATH79 && GENERIC_GPIO
  65         select SPI_BITBANG
  66         help
  67           This enables support for the SPI controller present on the
  68           Atheros AR71XX/AR724X/AR913X SoCs.
  69
  70 config SPI_ATMEL
  71         tristate "Atmel SPI Controller"
  72         depends on (ARCH_AT91 || AVR32)
  73         help
  74           This selects a driver for the Atmel SPI Controller, present on
  75           many AT32 (AVR32) and AT91 (ARM) chips.
  76
  77 config SPI_BFIN5XX
  78         tristate "SPI controller driver for ADI Blackfin5xx"
  79         depends on BLACKFIN
  80         help
  81           This is the SPI controller master driver for Blackfin 5xx processor.
  82
  83 config SPI_BFIN_SPORT
  84         tristate "SPI bus via Blackfin SPORT"
  85         depends on BLACKFIN
  86         help
  87           Enable support for a SPI bus via the Blackfin SPORT peripheral.
  88
  89 config SPI_AU1550
  90         tristate "Au1550/Au1200/Au1300 SPI Controller"
  91         depends on MIPS_ALCHEMY && EXPERIMENTAL
  92         select SPI_BITBANG
  93         help
  94           If you say yes to this option, support will be included for the
  95           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
  96
  97 config SPI_BCM63XX
  98         tristate "Broadcom BCM63xx SPI controller"
  99         depends on BCM63XX
 100         help
 101           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 102
 103 config SPI_BITBANG
 104         tristate "Utilities for Bitbanging SPI masters"
 105         help
 106           With a few GPIO pins, your system can bitbang the SPI protocol.
 107           Select this to get SPI support through I/O pins (GPIO, parallel
 108           port, etc).  Or, some systems' SPI master controller drivers use
 109           this code to manage the per-word or per-transfer accesses to the
 110           hardware shift registers.
 111
 112           This is library code, and is automatically selected by drivers that
 113           need it.  You only need to select this explicitly to support driver
 114           modules that aren't part of this kernel tree.
 115
 116 config SPI_BUTTERFLY
 117         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 118         depends on PARPORT
 119         select SPI_BITBANG
 120         help
 121           This uses a custom parallel port cable to connect to an AVR
 122           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 123           inexpensive battery powered microcontroller evaluation board.
 124           This same cable can be used to flash new firmware.
 125
 126 config SPI_CLPS711X
 127         tristate "CLPS711X host SPI controller"
 128         depends on ARCH_CLPS711X
 129         help
 130           This enables dedicated general purpose SPI/Microwire1-compatible
 131           master mode interface (SSI1) for CLPS711X-based CPUs.
 132
 133 config SPI_COLDFIRE_QSPI
 134         tristate "Freescale Coldfire QSPI controller"
 135         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 136         help
 137           This enables support for the Coldfire QSPI controller in master
 138           mode.
 139
 140 config SPI_DAVINCI
 141         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 142         depends on ARCH_DAVINCI
 143         select SPI_BITBANG
 144         select TI_EDMA
 145         help
 146           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 147
 148 config SPI_EP93XX
 149         tristate "Cirrus Logic EP93xx SPI controller"
 150         depends on ARCH_EP93XX
 151         help
 152           This enables using the Cirrus EP93xx SPI controller in master
 153           mode.
 154
 155 config SPI_FALCON
 156         tristate "Falcon SPI controller support"
 157         depends on SOC_FALCON
 158         help
 159           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 160           emulation that is designed for serial flash access. This driver
 161           has only been tested with m25p80 type chips. The hardware has no
 162           support for other types of SPI peripherals.
 163
 164 config SPI_GPIO
 165         tristate "GPIO-based bitbanging SPI Master"
 166         depends on GENERIC_GPIO
 167         select SPI_BITBANG
 168         help
 169           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 170           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 171           slaves connected to a bus using this driver are configured as usual,
 172           except that the spi_board_info.controller_data holds the GPIO number
 173           for the chipselect used by this controller driver.
 174
 175           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 176           making it unusually slow for SPI.  If your platform can inline
 177           GPIO operations, you should be able to leverage that for better
 178           speed with a custom version of this driver; see the source code.
 179
 180 config SPI_IMX
 181         tristate "Freescale i.MX SPI controllers"
 182         depends on ARCH_MXC
 183         select SPI_BITBANG
 184         default m if IMX_HAVE_PLATFORM_SPI_IMX
 185         help
 186           This enables using the Freescale i.MX SPI controllers in master
 187           mode.
 188
 189 config SPI_LM70_LLP
 190         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 191         depends on PARPORT && EXPERIMENTAL
 192         select SPI_BITBANG
 193         help
 194           This driver supports the NS LM70 LLP Evaluation Board,
 195           which interfaces to an LM70 temperature sensor using
 196           a parallel port.
 197
 198 config SPI_MPC52xx
 199         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 200         depends on PPC_MPC52xx
 201         help
 202           This drivers supports the MPC52xx SPI controller in master SPI
 203           mode.
 204
 205 config SPI_MPC52xx_PSC
 206         tristate "Freescale MPC52xx PSC SPI controller"
 207         depends on PPC_MPC52xx && EXPERIMENTAL
 208         help
 209           This enables using the Freescale MPC52xx Programmable Serial
 210           Controller in master SPI mode.
 211
 212 config SPI_MPC512x_PSC
 213         tristate "Freescale MPC512x PSC SPI controller"
 214         depends on PPC_MPC512x
 215         help
 216           This enables using the Freescale MPC5121 Programmable Serial
 217           Controller in SPI master mode.
 218
 219 config SPI_FSL_LIB
 220         tristate
 221         depends on FSL_SOC
 222
 223 config SPI_FSL_SPI
 224         bool "Freescale SPI controller"
 225         depends on FSL_SOC
 226         select SPI_FSL_LIB
 227         help
 228           This enables using the Freescale SPI controllers in master mode.
 229           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 230           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 231
 232 config SPI_FSL_ESPI
 233         bool "Freescale eSPI controller"
 234         depends on FSL_SOC
 235         select SPI_FSL_LIB
 236         help
 237           This enables using the Freescale eSPI controllers in master mode.
 238           From MPC8536, 85xx platform uses the controller, and all P10xx,
 239           P20xx, P30xx,P40xx, P50xx uses this controller.
 240
 241 config SPI_OC_TINY
 242         tristate "OpenCores tiny SPI"
 243         depends on GENERIC_GPIO
 244         select SPI_BITBANG
 245         help
 246           This is the driver for OpenCores tiny SPI master controller.
 247
 248 config SPI_OCTEON
 249         tristate "Cavium OCTEON SPI controller"
 250         depends on CPU_CAVIUM_OCTEON
 251         help
 252           SPI host driver for the hardware found on some Cavium OCTEON
 253           SOCs.
 254
 255 config SPI_OMAP_UWIRE
 256         tristate "OMAP1 MicroWire"
 257         depends on ARCH_OMAP1
 258         select SPI_BITBANG
 259         help
 260           This hooks up to the MicroWire controller on OMAP1 chips.
 261
 262 config SPI_OMAP24XX
 263         tristate "McSPI driver for OMAP"
 264         depends on ARCH_OMAP2PLUS
 265         help
 266           SPI master controller for OMAP24XX and later Multichannel SPI
 267           (McSPI) modules.
 268
 269 config SPI_OMAP_100K
 270         tristate "OMAP SPI 100K"
 271         depends on ARCH_OMAP850 || ARCH_OMAP730
 272         help
 273           OMAP SPI 100K master controller for omap7xx boards.
 274
 275 config SPI_ORION
 276         tristate "Orion SPI master (EXPERIMENTAL)"
 277         depends on PLAT_ORION && EXPERIMENTAL
 278         help
 279           This enables using the SPI master controller on the Orion chips.
 280
 281 config SPI_PL022
 282         tristate "ARM AMBA PL022 SSP controller"
 283         depends on ARM_AMBA
 284         default y if MACH_U300
 285         default y if ARCH_REALVIEW
 286         default y if INTEGRATOR_IMPD1
 287         default y if ARCH_VERSATILE
 288         help
 289           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 290           controller. If you have an embedded system with an AMBA(R)
 291           bus and a PL022 controller, say Y or M here.
 292
 293 config SPI_PPC4xx
 294         tristate "PPC4xx SPI Controller"
 295         depends on PPC32 && 4xx
 296         select SPI_BITBANG
 297         help
 298           This selects a driver for the PPC4xx SPI Controller.
 299
 300 config SPI_PXA2XX
 301         tristate "PXA2xx SSP SPI master"
 302         depends on (ARCH_PXA || (X86_32 && PCI)) && EXPERIMENTAL
 303         select PXA_SSP if ARCH_PXA
 304         help
 305           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 306           controller. The driver can be configured to use any SSP port and
 307           additional documentation can be found a Documentation/spi/pxa2xx.
 308
 309 config SPI_PXA2XX_PCI
 310         def_bool SPI_PXA2XX && X86_32 && PCI
 311
 312 config SPI_RSPI
 313         tristate "Renesas RSPI controller"
 314         depends on SUPERH
 315         help
 316           SPI driver for Renesas RSPI blocks.
 317
 318 config SPI_S3C24XX
 319         tristate "Samsung S3C24XX series SPI"
 320         depends on ARCH_S3C24XX && EXPERIMENTAL
 321         select SPI_BITBANG
 322         help
 323           SPI driver for Samsung S3C24XX series ARM SoCs
 324
 325 config SPI_S3C24XX_FIQ
 326         bool "S3C24XX driver with FIQ pseudo-DMA"
 327         depends on SPI_S3C24XX
 328         select FIQ
 329         help
 330           Enable FIQ support for the S3C24XX SPI driver to provide pseudo
 331           DMA by using the fast-interrupt request framework, This allows
 332           the driver to get DMA-like performance when there are either
 333           no free DMA channels, or when doing transfers that required both
 334           TX and RX data paths.
 335
 336 config SPI_S3C64XX
 337         tristate "Samsung S3C64XX series type SPI"
 338         depends on (ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5P64X0 || ARCH_EXYNOS)
 339         select S3C64XX_DMA if ARCH_S3C64XX
 340         help
 341           SPI driver for Samsung S3C64XX and newer SoCs.
 342
 343 config SPI_SC18IS602
 344         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 345         depends on I2C
 346         help
 347           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 348
 349 config SPI_SH_MSIOF
 350         tristate "SuperH MSIOF SPI controller"
 351         depends on (SUPERH || ARCH_SHMOBILE) && HAVE_CLK
 352         select SPI_BITBANG
 353         help
 354           SPI driver for SuperH and SH Mobile MSIOF blocks.
 355
 356 config SPI_SH
 357         tristate "SuperH SPI controller"
 358         depends on SUPERH
 359         help
 360           SPI driver for SuperH SPI blocks.
 361
 362 config SPI_SH_SCI
 363         tristate "SuperH SCI SPI controller"
 364         depends on SUPERH
 365         select SPI_BITBANG
 366         help
 367           SPI driver for SuperH SCI blocks.
 368
 369 config SPI_SH_HSPI
 370         tristate "SuperH HSPI controller"
 371         depends on ARCH_SHMOBILE
 372         help
 373           SPI driver for SuperH HSPI blocks.
 374
 375 config SPI_SIRF
 376         tristate "CSR SiRFprimaII SPI controller"
 377         depends on ARCH_PRIMA2
 378         select SPI_BITBANG
 379         help
 380           SPI driver for CSR SiRFprimaII SoCs
 381
 382 config SPI_MXS
 383         tristate "Freescale MXS SPI controller"
 384         depends on ARCH_MXS
 385         select STMP_DEVICE
 386         help
 387           SPI driver for Freescale MXS devices.
 388
 389 config SPI_TEGRA20_SFLASH
 390         tristate "Nvidia Tegra20 Serial flash Controller"
 391         depends on ARCH_TEGRA
 392         help
 393           SPI driver for Nvidia Tegra20 Serial flash Controller interface.
 394           The main usecase of this controller is to use spi flash as boot
 395           device.
 396
 397 config SPI_TEGRA20_SLINK
 398         tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
 399         depends on ARCH_TEGRA && TEGRA20_APB_DMA
 400         help
 401           SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
 402
 403 config SPI_TI_SSP
 404         tristate "TI Sequencer Serial Port - SPI Support"
 405         depends on MFD_TI_SSP
 406         help
 407           This selects an SPI master implementation using a TI sequencer
 408           serial port.
 409
 410 config SPI_TOPCLIFF_PCH
 411         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
 412         depends on PCI
 413         help
 414           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
 415           used in some x86 embedded processors.
 416
 417           This driver also supports the ML7213/ML7223/ML7831, a companion chip
 418           for the Atom E6xx series and compatible with the Intel EG20T PCH.
 419
 420 config SPI_TXX9
 421         tristate "Toshiba TXx9 SPI controller"
 422         depends on GENERIC_GPIO && CPU_TX49XX
 423         help
 424           SPI driver for Toshiba TXx9 MIPS SoCs
 425
 426 config SPI_XCOMM
 427         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
 428         depends on I2C
 429         help
 430           Support for the SPI-I2C bridge found on the Analog Devices
 431           AD-FMCOMMS1-EBZ board.
 432
 433 config SPI_XILINX
 434         tristate "Xilinx SPI controller common module"
 435         depends on HAS_IOMEM && EXPERIMENTAL
 436         select SPI_BITBANG
 437         help
 438           This exposes the SPI controller IP from the Xilinx EDK.
 439
 440           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
 441           Product Specification document (DS464) for hardware details.
 442
 443           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
 444
 445 config SPI_NUC900
 446         tristate "Nuvoton NUC900 series SPI"
 447         depends on ARCH_W90X900 && EXPERIMENTAL
 448         select SPI_BITBANG
 449         help
 450           SPI driver for Nuvoton NUC900 series ARM SoCs
 451
 452 #
 453 # Add new SPI master controllers in alphabetical order above this line
 454 #
 455
 456 config SPI_DESIGNWARE
 457         tristate "DesignWare SPI controller core support"
 458         help
 459           general driver for SPI controller core from DesignWare
 460
 461 config SPI_DW_PCI
 462         tristate "PCI interface driver for DW SPI core"
 463         depends on SPI_DESIGNWARE && PCI
 464
 465 config SPI_DW_MID_DMA
 466         bool "DMA support for DW SPI controller on Intel Moorestown platform"
 467         depends on SPI_DW_PCI && INTEL_MID_DMAC
 468
 469 config SPI_DW_MMIO
 470         tristate "Memory-mapped io interface driver for DW SPI core"
 471         depends on SPI_DESIGNWARE && HAVE_CLK
 472
 473 #
 474 # There are lots of SPI device types, with sensors and memory
 475 # being probably the most widely used ones.
 476 #
 477 comment "SPI Protocol Masters"
 478
 479 config SPI_SPIDEV
 480         tristate "User mode SPI device driver support"
 481         depends on EXPERIMENTAL
 482         help
 483           This supports user mode SPI protocol drivers.
 484
 485           Note that this application programming interface is EXPERIMENTAL
 486           and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
 487
 488 config SPI_TLE62X0
 489         tristate "Infineon TLE62X0 (for power switching)"
 490         depends on SYSFS
 491         help
 492           SPI driver for Infineon TLE62X0 series line driver chips,
 493           such as the TLE6220, TLE6230 and TLE6240.  This provides a
 494           sysfs interface, with each line presented as a kind of GPIO
 495           exposing both switch control and diagnostic feedback.
 496
 497 #
 498 # Add new SPI protocol masters in alphabetical order above this line
 499 #
 500
 501 endif # SPI_MASTER
 502
 503 # (slave support would go here)
 504
 505 endif # SPI