drivers/rtc/Kconfig

   1 #
   2 # RTC class/drivers configuration
   3 #
   4
   5 config RTC_LIB
   6         bool
   7
   8 menuconfig RTC_CLASS
   9         bool "Real Time Clock"
  10         default n
  11         depends on !S390 && !UML
  12         select RTC_LIB
  13         help
  14           Generic RTC class support. If you say yes here, you will
  15           be allowed to plug one or more RTCs to your system. You will
  16           probably want to enable one or more of the interfaces below.
  17
  18 if RTC_CLASS
  19
  20 config RTC_HCTOSYS
  21         bool "Set system time from RTC on startup and resume"
  22         default y
  23         help
  24           If you say yes here, the system time (wall clock) will be set using
  25           the value read from a specified RTC device. This is useful to avoid
  26           unnecessary fsck runs at boot time, and to network better.
  27
  28 config RTC_SYSTOHC
  29         bool "Set the RTC time based on NTP synchronization"
  30         default y
  31         help
  32           If you say yes here, the system time (wall clock) will be stored
  33           in the RTC specified by RTC_HCTOSYS_DEVICE approximately every 11
  34           minutes if userspace reports synchronized NTP status.
  35
  36 config RTC_HCTOSYS_DEVICE
  37         string "RTC used to set the system time"
  38         depends on RTC_HCTOSYS = y || RTC_SYSTOHC = y
  39         default "rtc0"
  40         help
  41           The RTC device that will be used to (re)initialize the system
  42           clock, usually rtc0. Initialization is done when the system
  43           starts up, and when it resumes from a low power state. This
  44           device should record time in UTC, since the kernel won't do
  45           timezone correction.
  46
  47           The driver for this RTC device must be loaded before late_initcall
  48           functions run, so it must usually be statically linked.
  49
  50           This clock should be battery-backed, so that it reads the correct
  51           time when the system boots from a power-off state. Otherwise, your
  52           system will need an external clock source (like an NTP server).
  53
  54           If the clock you specify here is not battery backed, it may still
  55           be useful to reinitialize system time when resuming from system
  56           sleep states. Do not specify an RTC here unless it stays powered
  57           during all this system's supported sleep states.
  58
  59 config RTC_DEBUG
  60         bool "RTC debug support"
  61         help
  62           Say yes here to enable debugging support in the RTC framework
  63           and individual RTC drivers.
  64
  65 comment "RTC interfaces"
  66
  67 config RTC_INTF_SYSFS
  68         boolean "/sys/class/rtc/rtcN (sysfs)"
  69         depends on SYSFS
  70         default RTC_CLASS
  71         help
  72           Say yes here if you want to use your RTCs using sysfs interfaces,
  73           /sys/class/rtc/rtc0 through /sys/.../rtcN.
  74
  75           If unsure, say Y.
  76
  77 config RTC_INTF_PROC
  78         boolean "/proc/driver/rtc (procfs for rtcN)"
  79         depends on PROC_FS
  80         default RTC_CLASS
  81         help
  82           Say yes here if you want to use your system clock RTC through
  83           the proc interface, /proc/driver/rtc.
  84           Other RTCs will not be available through that API.
  85           If there is no RTC for the system clock, then the first RTC(rtc0)
  86           is used by default.
  87
  88           If unsure, say Y.
  89
  90 config RTC_INTF_DEV
  91         boolean "/dev/rtcN (character devices)"
  92         default RTC_CLASS
  93         help
  94           Say yes here if you want to use your RTCs using the /dev
  95           interfaces, which "udev" sets up as /dev/rtc0 through
  96           /dev/rtcN.
  97
  98           You may want to set up a symbolic link so one of these
  99           can be accessed as /dev/rtc, which is a name
 100           expected by "hwclock" and some other programs. Recent
 101           versions of "udev" are known to set up the symlink for you.
 102
 103           If unsure, say Y.
 104
 105 config RTC_INTF_DEV_UIE_EMUL
 106         bool "RTC UIE emulation on dev interface"
 107         depends on RTC_INTF_DEV
 108         help
 109           Provides an emulation for RTC_UIE if the underlying rtc chip
 110           driver does not expose RTC_UIE ioctls. Those requests generate
 111           once-per-second update interrupts, used for synchronization.
 112
 113           The emulation code will read the time from the hardware
 114           clock several times per second, please enable this option
 115           only if you know that you really need it.
 116
 117 config RTC_DRV_TEST
 118         tristate "Test driver/device"
 119         help
 120           If you say yes here you get support for the
 121           RTC test driver. It's a software RTC which can be
 122           used to test the RTC subsystem APIs. It gets
 123           the time from the system clock.
 124           You want this driver only if you are doing development
 125           on the RTC subsystem. Please read the source code
 126           for further details.
 127
 128           This driver can also be built as a module. If so, the module
 129           will be called rtc-test.
 130
 131 comment "I2C RTC drivers"
 132         depends on I2C
 133
 134 if I2C
 135
 136 config RTC_DRV_88PM860X
 137         tristate "Marvell 88PM860x"
 138         depends on I2C && MFD_88PM860X
 139         help
 140           If you say yes here you get support for RTC function in Marvell
 141           88PM860x chips.
 142
 143           This driver can also be built as a module. If so, the module
 144           will be called rtc-88pm860x.
 145
 146 config RTC_DRV_88PM80X
 147         tristate "Marvell 88PM80x"
 148         depends on I2C && MFD_88PM800
 149         help
 150           If you say yes here you get support for RTC function in Marvell
 151           88PM80x chips.
 152
 153           This driver can also be built as a module. If so, the module
 154           will be called rtc-88pm80x.
 155
 156 config RTC_DRV_AS3722
 157         tristate "ams AS3722 RTC driver"
 158         depends on MFD_AS3722
 159         help
 160           If you say yes here you get support for the RTC of ams AS3722 PMIC
 161           chips.
 162
 163           This driver can also be built as a module. If so, the module
 164           will be called rtc-as3722.
 165
 166 config RTC_DRV_DS1307
 167         tristate "Dallas/Maxim DS1307/37/38/39/40, ST M41T00, EPSON RX-8025"
 168         help
 169           If you say yes here you get support for various compatible RTC
 170           chips (often with battery backup) connected with I2C. This driver
 171           should handle DS1307, DS1337, DS1338, DS1339, DS1340, ST M41T00,
 172           EPSON RX-8025 and probably other chips. In some cases the RTC
 173           must already have been initialized (by manufacturing or a
 174           bootloader).
 175
 176           The first seven registers on these chips hold an RTC, and other
 177           registers may add features such as NVRAM, a trickle charger for
 178           the RTC/NVRAM backup power, and alarms. NVRAM is visible in
 179           sysfs, but other chip features may not be available.
 180
 181           This driver can also be built as a module. If so, the module
 182           will be called rtc-ds1307.
 183
 184 config RTC_DRV_DS1374
 185         tristate "Dallas/Maxim DS1374"
 186         depends on I2C
 187         help
 188           If you say yes here you get support for Dallas Semiconductor
 189           DS1374 real-time clock chips. If an interrupt is associated
 190           with the device, the alarm functionality is supported.
 191
 192           This driver can also be built as a module. If so, the module
 193           will be called rtc-ds1374.
 194
 195 config RTC_DRV_DS1672
 196         tristate "Dallas/Maxim DS1672"
 197         help
 198           If you say yes here you get support for the
 199           Dallas/Maxim DS1672 timekeeping chip.
 200
 201           This driver can also be built as a module. If so, the module
 202           will be called rtc-ds1672.
 203
 204 config RTC_DRV_DS3232
 205         tristate "Dallas/Maxim DS3232"
 206         depends on I2C
 207         help
 208           If you say yes here you get support for Dallas Semiconductor
 209           DS3232 real-time clock chips. If an interrupt is associated
 210           with the device, the alarm functionality is supported.
 211
 212           This driver can also be built as a module.  If so, the module
 213           will be called rtc-ds3232.
 214
 215 config RTC_DRV_HYM8563
 216         tristate "Haoyu Microelectronics HYM8563"
 217         depends on I2C && OF
 218         help
 219           Say Y to enable support for the HYM8563 I2C RTC chip. Apart
 220           from the usual rtc functions it provides a clock output of
 221           up to 32kHz.
 222
 223           This driver can also be built as a module. If so, the module
 224           will be called rtc-hym8563.
 225
 226 config RTC_DRV_LP8788
 227         tristate "TI LP8788 RTC driver"
 228         depends on MFD_LP8788
 229         help
 230           Say Y to enable support for the LP8788 RTC/ALARM driver.
 231
 232 config RTC_DRV_MAX6900
 233         tristate "Maxim MAX6900"
 234         help
 235           If you say yes here you will get support for the
 236           Maxim MAX6900 I2C RTC chip.
 237
 238           This driver can also be built as a module. If so, the module
 239           will be called rtc-max6900.
 240
 241 config RTC_DRV_MAX8907
 242         tristate "Maxim MAX8907"
 243         depends on MFD_MAX8907
 244         help
 245           If you say yes here you will get support for the
 246           RTC of Maxim MAX8907 PMIC.
 247
 248           This driver can also be built as a module. If so, the module
 249           will be called rtc-max8907.
 250
 251 config RTC_DRV_MAX8925
 252         tristate "Maxim MAX8925"
 253         depends on MFD_MAX8925
 254         help
 255           If you say yes here you will get support for the
 256           RTC of Maxim MAX8925 PMIC.
 257
 258           This driver can also be built as a module. If so, the module
 259           will be called rtc-max8925.
 260
 261 config RTC_DRV_MAX8998
 262         tristate "Maxim MAX8998"
 263         depends on MFD_MAX8998
 264         help
 265           If you say yes here you will get support for the
 266           RTC of Maxim MAX8998 PMIC.
 267
 268           This driver can also be built as a module. If so, the module
 269           will be called rtc-max8998.
 270
 271 config RTC_DRV_MAX8997
 272         tristate "Maxim MAX8997"
 273         depends on MFD_MAX8997
 274         help
 275           If you say yes here you will get support for the
 276           RTC of Maxim MAX8997 PMIC.
 277
 278           This driver can also be built as a module. If so, the module
 279           will be called rtc-max8997.
 280
 281 config RTC_DRV_MAX77686
 282         tristate "Maxim MAX77686"
 283         depends on MFD_MAX77686
 284         help
 285           If you say yes here you will get support for the
 286           RTC of Maxim MAX77686 PMIC.
 287
 288           This driver can also be built as a module. If so, the module
 289           will be called rtc-max77686.
 290
 291 config RTC_DRV_RK808
 292         tristate "Rockchip RK808 RTC"
 293         depends on MFD_RK808
 294         help
 295           If you say yes here you will get support for the
 296           RTC of RK808 PMIC.
 297
 298           This driver can also be built as a module. If so, the module
 299           will be called rk808-rtc.
 300
 301 config RTC_DRV_MAX77802
 302         tristate "Maxim 77802 RTC"
 303         depends on MFD_MAX77686
 304         help
 305           If you say yes here you will get support for the
 306           RTC of Maxim MAX77802 PMIC.
 307
 308           This driver can also be built as a module. If so, the module
 309           will be called rtc-max77802.
 310
 311 config RTC_DRV_RS5C372
 312         tristate "Ricoh R2025S/D, RS5C372A/B, RV5C386, RV5C387A"
 313         help
 314           If you say yes here you get support for the
 315           Ricoh R2025S/D, RS5C372A, RS5C372B, RV5C386, and RV5C387A RTC chips.
 316
 317           This driver can also be built as a module. If so, the module
 318           will be called rtc-rs5c372.
 319
 320 config RTC_DRV_ISL1208
 321         tristate "Intersil ISL1208"
 322         help
 323           If you say yes here you get support for the
 324           Intersil ISL1208 RTC chip.
 325
 326           This driver can also be built as a module. If so, the module
 327           will be called rtc-isl1208.
 328
 329 config RTC_DRV_ISL12022
 330         tristate "Intersil ISL12022"
 331         help
 332           If you say yes here you get support for the
 333           Intersil ISL12022 RTC chip.
 334
 335           This driver can also be built as a module. If so, the module
 336           will be called rtc-isl12022.
 337
 338 config RTC_DRV_ISL12057
 339        depends on I2C
 340        select REGMAP_I2C
 341        tristate "Intersil ISL12057"
 342        help
 343           If you say yes here you get support for the Intersil ISL12057
 344           I2C RTC chip.
 345
 346           This driver can also be built as a module. If so, the module
 347           will be called rtc-isl12057.
 348
 349 config RTC_DRV_X1205
 350         tristate "Xicor/Intersil X1205"
 351         help
 352           If you say yes here you get support for the
 353           Xicor/Intersil X1205 RTC chip.
 354
 355           This driver can also be built as a module. If so, the module
 356           will be called rtc-x1205.
 357
 358 config RTC_DRV_PALMAS
 359         tristate "TI Palmas RTC driver"
 360         depends on MFD_PALMAS
 361         help
 362           If you say yes here you get support for the RTC of TI PALMA series PMIC
 363           chips.
 364
 365           This driver can also be built as a module. If so, the module
 366           will be called rtc-palma.
 367
 368 config RTC_DRV_PCF2127
 369         tristate "NXP PCF2127"
 370         help
 371           If you say yes here you get support for the NXP PCF2127/29 RTC
 372           chips.
 373
 374           This driver can also be built as a module. If so, the module
 375           will be called rtc-pcf2127.
 376
 377 config RTC_DRV_PCF8523
 378         tristate "NXP PCF8523"
 379         help
 380           If you say yes here you get support for the NXP PCF8523 RTC
 381           chips.
 382
 383           This driver can also be built as a module. If so, the module
 384           will be called rtc-pcf8523.
 385
 386 config RTC_DRV_PCF8563
 387         tristate "Philips PCF8563/Epson RTC8564"
 388         help
 389           If you say yes here you get support for the
 390           Philips PCF8563 RTC chip. The Epson RTC8564
 391           should work as well.
 392
 393           This driver can also be built as a module. If so, the module
 394           will be called rtc-pcf8563.
 395
 396 config RTC_DRV_PCF85063
 397         tristate "nxp PCF85063"
 398         help
 399           If you say yes here you get support for the PCF85063 RTC chip
 400
 401           This driver can also be built as a module. If so, the module
 402           will be called rtc-pcf85063.
 403
 404 config RTC_DRV_PCF8583
 405         tristate "Philips PCF8583"
 406         help
 407           If you say yes here you get support for the Philips PCF8583
 408           RTC chip found on Acorn RiscPCs. This driver supports the
 409           platform specific method of retrieving the current year from
 410           the RTC's SRAM. It will work on other platforms with the same
 411           chip, but the year will probably have to be tweaked.
 412
 413           This driver can also be built as a module. If so, the module
 414           will be called rtc-pcf8583.
 415
 416 config RTC_DRV_M41T80
 417         tristate "ST M41T62/65/M41T80/81/82/83/84/85/87 and compatible"
 418         help
 419           If you say Y here you will get support for the ST M41T60
 420           and M41T80 RTC chips series. Currently, the following chips are
 421           supported: M41T62, M41T65, M41T80, M41T81, M41T82, M41T83, M41ST84,
 422           M41ST85, M41ST87, and MicroCrystal RV4162.
 423
 424           This driver can also be built as a module. If so, the module
 425           will be called rtc-m41t80.
 426
 427 config RTC_DRV_M41T80_WDT
 428         bool "ST M41T65/M41T80 series RTC watchdog timer"
 429         depends on RTC_DRV_M41T80
 430         help
 431           If you say Y here you will get support for the
 432           watchdog timer in the ST M41T60 and M41T80 RTC chips series.
 433
 434 config RTC_DRV_BQ32K
 435         tristate "TI BQ32000"
 436         help
 437           If you say Y here you will get support for the TI
 438           BQ32000 I2C RTC chip.
 439
 440           This driver can also be built as a module. If so, the module
 441           will be called rtc-bq32k.
 442
 443 config RTC_DRV_DM355EVM
 444         tristate "TI DaVinci DM355 EVM RTC"
 445         depends on MFD_DM355EVM_MSP
 446         help
 447           Supports the RTC firmware in the MSP430 on the DM355 EVM.
 448
 449 config RTC_DRV_TWL92330
 450         boolean "TI TWL92330/Menelaus"
 451         depends on MENELAUS
 452         help
 453           If you say yes here you get support for the RTC on the
 454           TWL92330 "Menelaus" power management chip, used with OMAP2
 455           platforms. The support is integrated with the rest of
 456           the Menelaus driver; it's not separate module.
 457
 458 config RTC_DRV_TWL4030
 459         tristate "TI TWL4030/TWL5030/TWL6030/TPS659x0"
 460         depends on TWL4030_CORE
 461         help
 462           If you say yes here you get support for the RTC on the
 463           TWL4030/TWL5030/TWL6030 family chips, used mostly with OMAP3 platforms.
 464
 465           This driver can also be built as a module. If so, the module
 466           will be called rtc-twl.
 467
 468 config RTC_DRV_TPS6586X
 469         tristate "TI TPS6586X RTC driver"
 470         depends on MFD_TPS6586X
 471         help
 472           TI Power Management IC TPS6586X supports RTC functionality
 473           along with alarm. This driver supports the RTC driver for
 474           the TPS6586X RTC module.
 475
 476 config RTC_DRV_TPS65910
 477         tristate "TI TPS65910 RTC driver"
 478         depends on RTC_CLASS && MFD_TPS65910
 479         help
 480           If you say yes here you get support for the RTC on the
 481           TPS65910 chips.
 482
 483           This driver can also be built as a module. If so, the module
 484           will be called rtc-tps65910.
 485
 486 config RTC_DRV_TPS80031
 487         tristate "TI TPS80031/TPS80032 RTC driver"
 488         depends on MFD_TPS80031
 489         help
 490           TI Power Management IC TPS80031 supports RTC functionality
 491           along with alarm. This driver supports the RTC driver for
 492           the TPS80031 RTC module.
 493
 494 config RTC_DRV_RC5T583
 495         tristate "RICOH 5T583 RTC driver"
 496         depends on MFD_RC5T583
 497         help
 498           If you say yes here you get support for the RTC on the
 499           RICOH 5T583 chips.
 500
 501           This driver can also be built as a module. If so, the module
 502           will be called rtc-rc5t583.
 503
 504 config RTC_DRV_S35390A
 505         tristate "Seiko Instruments S-35390A"
 506         select BITREVERSE
 507         help
 508           If you say yes here you will get support for the Seiko
 509           Instruments S-35390A.
 510
 511           This driver can also be built as a module. If so the module
 512           will be called rtc-s35390a.
 513
 514 config RTC_DRV_FM3130
 515         tristate "Ramtron FM3130"
 516         help
 517           If you say Y here you will get support for the
 518           Ramtron FM3130 RTC chips.
 519           Ramtron FM3130 is a chip with two separate devices inside,
 520           RTC clock and FRAM. This driver provides only RTC functionality.
 521
 522           This driver can also be built as a module. If so the module
 523           will be called rtc-fm3130.
 524
 525 config RTC_DRV_RX8581
 526         tristate "Epson RX-8581"
 527         help
 528           If you say yes here you will get support for the Epson RX-8581.
 529
 530           This driver can also be built as a module. If so the module
 531           will be called rtc-rx8581.
 532
 533 config RTC_DRV_RX8025
 534         tristate "Epson RX-8025SA/NB"
 535         help
 536           If you say yes here you get support for the Epson
 537           RX-8025SA/NB RTC chips.
 538
 539           This driver can also be built as a module. If so, the module
 540           will be called rtc-rx8025.
 541
 542 config RTC_DRV_EM3027
 543         tristate "EM Microelectronic EM3027"
 544         help
 545           If you say yes here you get support for the EM
 546           Microelectronic EM3027 RTC chips.
 547
 548           This driver can also be built as a module. If so, the module
 549           will be called rtc-em3027.
 550
 551 config RTC_DRV_RV3029C2
 552         tristate "Micro Crystal RTC"
 553         help
 554           If you say yes here you get support for the Micro Crystal
 555           RV3029-C2 RTC chips.
 556
 557           This driver can also be built as a module. If so, the module
 558           will be called rtc-rv3029c2.
 559
 560 config RTC_DRV_S5M
 561         tristate "Samsung S2M/S5M series"
 562         depends on MFD_SEC_CORE
 563         help
 564           If you say yes here you will get support for the
 565           RTC of Samsung S2MPS14 and S5M PMIC series.
 566
 567           This driver can also be built as a module. If so, the module
 568           will be called rtc-s5m.
 569
 570 endif # I2C
 571
 572 comment "SPI RTC drivers"
 573
 574 if SPI_MASTER
 575
 576 config RTC_DRV_M41T93
 577         tristate "ST M41T93"
 578         help
 579           If you say yes here you will get support for the
 580           ST M41T93 SPI RTC chip.
 581
 582           This driver can also be built as a module. If so, the module
 583           will be called rtc-m41t93.
 584
 585 config RTC_DRV_M41T94
 586         tristate "ST M41T94"
 587         help
 588           If you say yes here you will get support for the
 589           ST M41T94 SPI RTC chip.
 590
 591           This driver can also be built as a module. If so, the module
 592           will be called rtc-m41t94.
 593
 594 config RTC_DRV_DS1305
 595         tristate "Dallas/Maxim DS1305/DS1306"
 596         help
 597           Select this driver to get support for the Dallas/Maxim DS1305
 598           and DS1306 real time clock chips. These support a trickle
 599           charger, alarms, and NVRAM in addition to the clock.
 600
 601           This driver can also be built as a module. If so, the module
 602           will be called rtc-ds1305.
 603
 604 config RTC_DRV_DS1343
 605         select REGMAP_SPI
 606         tristate "Dallas/Maxim DS1343/DS1344"
 607         help
 608           If you say yes here you get support for the
 609           Dallas/Maxim DS1343 and DS1344 real time clock chips.
 610           Support for trickle charger, alarm is provided.
 611
 612           This driver can also be built as a module. If so, the module
 613           will be called rtc-ds1343.
 614
 615 config RTC_DRV_DS1347
 616         tristate "Dallas/Maxim DS1347"
 617         help
 618           If you say yes here you get support for the
 619           Dallas/Maxim DS1347 chips.
 620
 621           This driver only supports the RTC feature, and not other chip
 622           features such as alarms.
 623
 624           This driver can also be built as a module. If so, the module
 625           will be called rtc-ds1347.
 626
 627 config RTC_DRV_DS1390
 628         tristate "Dallas/Maxim DS1390/93/94"
 629         help
 630           If you say yes here you get support for the
 631           Dallas/Maxim DS1390/93/94 chips.
 632
 633           This driver only supports the RTC feature, and not other chip
 634           features such as alarms and trickle charging.
 635
 636           This driver can also be built as a module. If so, the module
 637           will be called rtc-ds1390.
 638
 639 config RTC_DRV_MAX6902
 640         tristate "Maxim MAX6902"
 641         help
 642           If you say yes here you will get support for the
 643           Maxim MAX6902 SPI RTC chip.
 644
 645           This driver can also be built as a module. If so, the module
 646           will be called rtc-max6902.
 647
 648 config RTC_DRV_R9701
 649         tristate "Epson RTC-9701JE"
 650         help
 651           If you say yes here you will get support for the
 652           Epson RTC-9701JE SPI RTC chip.
 653
 654           This driver can also be built as a module. If so, the module
 655           will be called rtc-r9701.
 656
 657 config RTC_DRV_RS5C348
 658         tristate "Ricoh RS5C348A/B"
 659         help
 660           If you say yes here you get support for the
 661           Ricoh RS5C348A and RS5C348B RTC chips.
 662
 663           This driver can also be built as a module. If so, the module
 664           will be called rtc-rs5c348.
 665
 666 config RTC_DRV_DS3234
 667         tristate "Maxim/Dallas DS3234"
 668         help
 669           If you say yes here you get support for the
 670           Maxim/Dallas DS3234 SPI RTC chip.
 671
 672           This driver can also be built as a module. If so, the module
 673           will be called rtc-ds3234.
 674
 675 config RTC_DRV_PCF2123
 676         tristate "NXP PCF2123"
 677         help
 678           If you say yes here you get support for the NXP PCF2123
 679           RTC chip.
 680
 681           This driver can also be built as a module. If so, the module
 682           will be called rtc-pcf2123.
 683
 684 config RTC_DRV_RX4581
 685         tristate "Epson RX-4581"
 686         help
 687           If you say yes here you will get support for the Epson RX-4581.
 688
 689           This driver can also be built as a module. If so the module
 690           will be called rtc-rx4581.
 691
 692 config RTC_DRV_MCP795
 693         tristate "Microchip MCP795"
 694         help
 695           If you say yes here you will get support for the Microchip MCP795.
 696
 697           This driver can also be built as a module. If so the module
 698           will be called rtc-mcp795.
 699
 700 endif # SPI_MASTER
 701
 702 comment "Platform RTC drivers"
 703
 704 # this 'CMOS' RTC driver is arch dependent because <asm-generic/rtc.h>
 705 # requires <asm/mc146818rtc.h> defining CMOS_READ/CMOS_WRITE, and a
 706 # global rtc_lock ... it's not yet just another platform_device.
 707
 708 config RTC_DRV_CMOS
 709         tristate "PC-style 'CMOS'"
 710         depends on X86 || ARM || M32R || PPC || MIPS || SPARC64
 711         default y if X86
 712         help
 713           Say "yes" here to get direct support for the real time clock
 714           found in every PC or ACPI-based system, and some other boards.
 715           Specifically the original MC146818, compatibles like those in
 716           PC south bridges, the DS12887 or M48T86, some multifunction
 717           or LPC bus chips, and so on.
 718
 719           Your system will need to define the platform device used by
 720           this driver, otherwise it won't be accessible. This means
 721           you can safely enable this driver if you don't know whether
 722           or not your board has this kind of hardware.
 723
 724           This driver can also be built as a module. If so, the module
 725           will be called rtc-cmos.
 726
 727 config RTC_DRV_ALPHA
 728         bool "Alpha PC-style CMOS"
 729         depends on ALPHA
 730         default y
 731         help
 732           Direct support for the real-time clock found on every Alpha
 733           system, specifically MC146818 compatibles.  If in doubt, say Y.
 734
 735 config RTC_DRV_VRTC
 736         tristate "Virtual RTC for Intel MID platforms"
 737         depends on X86_INTEL_MID
 738         default y if X86_INTEL_MID
 739
 740         help
 741         Say "yes" here to get direct support for the real time clock
 742         found on Moorestown platforms. The VRTC is a emulated RTC that
 743         derives its clock source from a real RTC in the PMIC. The MC146818
 744         style programming interface is mostly conserved, but any
 745         updates are done via IPC calls to the system controller FW.
 746
 747 config RTC_DRV_DS1216
 748         tristate "Dallas DS1216"
 749         depends on SNI_RM
 750         help
 751           If you say yes here you get support for the Dallas DS1216 RTC chips.
 752
 753 config RTC_DRV_DS1286
 754         tristate "Dallas DS1286"
 755         depends on HAS_IOMEM
 756         help
 757           If you say yes here you get support for the Dallas DS1286 RTC chips.
 758
 759 config RTC_DRV_DS1302
 760         tristate "Dallas DS1302"
 761         depends on SH_SECUREEDGE5410
 762         help
 763           If you say yes here you get support for the Dallas DS1302 RTC chips.
 764
 765 config RTC_DRV_DS1511
 766         tristate "Dallas DS1511"
 767         depends on HAS_IOMEM
 768         help
 769           If you say yes here you get support for the
 770           Dallas DS1511 timekeeping/watchdog chip.
 771
 772           This driver can also be built as a module. If so, the module
 773           will be called rtc-ds1511.
 774
 775 config RTC_DRV_DS1553
 776         tristate "Maxim/Dallas DS1553"
 777         depends on HAS_IOMEM
 778         help
 779           If you say yes here you get support for the
 780           Maxim/Dallas DS1553 timekeeping chip.
 781
 782           This driver can also be built as a module. If so, the module
 783           will be called rtc-ds1553.
 784
 785 config RTC_DRV_DS1742
 786         tristate "Maxim/Dallas DS1742/1743"
 787         depends on HAS_IOMEM
 788         help
 789           If you say yes here you get support for the
 790           Maxim/Dallas DS1742/1743 timekeeping chip.
 791
 792           This driver can also be built as a module. If so, the module
 793           will be called rtc-ds1742.
 794
 795 config RTC_DRV_DS2404
 796         tristate "Maxim/Dallas DS2404"
 797         help
 798           If you say yes here you get support for the
 799           Dallas DS2404 RTC chip.
 800
 801           This driver can also be built as a module. If so, the module
 802           will be called rtc-ds2404.
 803
 804 config RTC_DRV_DA9052
 805         tristate "Dialog DA9052/DA9053 RTC"
 806         depends on PMIC_DA9052
 807         help
 808           Say y here to support the RTC driver for Dialog Semiconductor
 809           DA9052-BC and DA9053-AA/Bx PMICs.
 810
 811 config RTC_DRV_DA9055
 812         tristate "Dialog Semiconductor DA9055 RTC"
 813         depends on MFD_DA9055
 814         help
 815           If you say yes here you will get support for the
 816           RTC of the Dialog DA9055 PMIC.
 817
 818           This driver can also be built as a module. If so, the module
 819           will be called rtc-da9055
 820
 821 config RTC_DRV_DA9063
 822         tristate "Dialog Semiconductor DA9063 RTC"
 823         depends on MFD_DA9063
 824         help
 825           If you say yes here you will get support for the RTC subsystem
 826           of the Dialog Semiconductor DA9063.
 827
 828           This driver can also be built as a module. If so, the module
 829           will be called "rtc-da9063".
 830
 831 config RTC_DRV_EFI
 832         tristate "EFI RTC"
 833         depends on EFI && !X86
 834         help
 835           If you say yes here you will get support for the EFI
 836           Real Time Clock.
 837
 838           This driver can also be built as a module. If so, the module
 839           will be called rtc-efi.
 840
 841 config RTC_DRV_STK17TA8
 842         tristate "Simtek STK17TA8"
 843         depends on HAS_IOMEM
 844         help
 845           If you say yes here you get support for the
 846           Simtek STK17TA8 timekeeping chip.
 847
 848           This driver can also be built as a module. If so, the module
 849           will be called rtc-stk17ta8.
 850
 851 config RTC_DRV_M48T86
 852         tristate "ST M48T86/Dallas DS12887"
 853         help
 854           If you say Y here you will get support for the
 855           ST M48T86 and Dallas DS12887 RTC chips.
 856
 857           This driver can also be built as a module. If so, the module
 858           will be called rtc-m48t86.
 859
 860 config RTC_DRV_M48T35
 861         tristate "ST M48T35"
 862         depends on HAS_IOMEM
 863         help
 864           If you say Y here you will get support for the
 865           ST M48T35 RTC chip.
 866
 867           This driver can also be built as a module, if so, the module
 868           will be called "rtc-m48t35".
 869
 870 config RTC_DRV_M48T59
 871         tristate "ST M48T59/M48T08/M48T02"
 872         depends on HAS_IOMEM
 873         help
 874           If you say Y here you will get support for the
 875           ST M48T59 RTC chip and compatible ST M48T08 and M48T02.
 876
 877           These chips are usually found in Sun SPARC and UltraSPARC
 878           workstations.
 879
 880           This driver can also be built as a module, if so, the module
 881           will be called "rtc-m48t59".
 882
 883 config RTC_DRV_MSM6242
 884         tristate "Oki MSM6242"
 885         depends on HAS_IOMEM
 886         help
 887           If you say yes here you get support for the Oki MSM6242
 888           timekeeping chip. It is used in some Amiga models (e.g. A2000).
 889
 890           This driver can also be built as a module. If so, the module
 891           will be called rtc-msm6242.
 892
 893 config RTC_DRV_BQ4802
 894         tristate "TI BQ4802"
 895         depends on HAS_IOMEM
 896         help
 897           If you say Y here you will get support for the TI
 898           BQ4802 RTC chip.
 899
 900           This driver can also be built as a module. If so, the module
 901           will be called rtc-bq4802.
 902
 903 config RTC_DRV_RP5C01
 904         tristate "Ricoh RP5C01"
 905         depends on HAS_IOMEM
 906         help
 907           If you say yes here you get support for the Ricoh RP5C01
 908           timekeeping chip. It is used in some Amiga models (e.g. A3000
 909           and A4000).
 910
 911           This driver can also be built as a module. If so, the module
 912           will be called rtc-rp5c01.
 913
 914 config RTC_DRV_V3020
 915         tristate "EM Microelectronic V3020"
 916         help
 917           If you say yes here you will get support for the
 918           EM Microelectronic v3020 RTC chip.
 919
 920           This driver can also be built as a module. If so, the module
 921           will be called rtc-v3020.
 922
 923 config RTC_DRV_WM831X
 924         tristate "Wolfson Microelectronics WM831x RTC"
 925         depends on MFD_WM831X
 926         help
 927           If you say yes here you will get support for the RTC subsystem
 928           of the Wolfson Microelectronics WM831X series PMICs.
 929
 930           This driver can also be built as a module. If so, the module
 931           will be called "rtc-wm831x".
 932
 933 config RTC_DRV_WM8350
 934         tristate "Wolfson Microelectronics WM8350 RTC"
 935         depends on MFD_WM8350
 936         help
 937           If you say yes here you will get support for the RTC subsystem
 938           of the Wolfson Microelectronics WM8350.
 939
 940           This driver can also be built as a module. If so, the module
 941           will be called "rtc-wm8350".
 942
 943 config RTC_DRV_SPEAR
 944         tristate "SPEAR ST RTC"
 945         depends on PLAT_SPEAR
 946         default y
 947         help
 948          If you say Y here you will get support for the RTC found on
 949          spear
 950
 951 config RTC_DRV_PCF50633
 952         depends on MFD_PCF50633
 953         tristate "NXP PCF50633 RTC"
 954         help
 955           If you say yes here you get support for the RTC subsystem of the
 956           NXP PCF50633 used in embedded systems.
 957
 958 config RTC_DRV_AB3100
 959         tristate "ST-Ericsson AB3100 RTC"
 960         depends on AB3100_CORE
 961         default y if AB3100_CORE
 962         help
 963           Select this to enable the ST-Ericsson AB3100 Mixed Signal IC RTC
 964           support. This chip contains a battery- and capacitor-backed RTC.
 965
 966 config RTC_DRV_AB8500
 967         tristate "ST-Ericsson AB8500 RTC"
 968         depends on AB8500_CORE
 969         select RTC_INTF_DEV
 970         select RTC_INTF_DEV_UIE_EMUL
 971         help
 972           Select this to enable the ST-Ericsson AB8500 power management IC RTC
 973           support. This chip contains a battery- and capacitor-backed RTC.
 974
 975 config RTC_DRV_NUC900
 976         tristate "NUC910/NUC920 RTC driver"
 977         depends on ARCH_W90X900
 978         help
 979           If you say yes here you get support for the RTC subsystem of the
 980           NUC910/NUC920 used in embedded systems.
 981
 982 comment "on-CPU RTC drivers"
 983
 984 config RTC_DRV_DAVINCI
 985         tristate "TI DaVinci RTC"
 986         depends on ARCH_DAVINCI_DM365
 987         help
 988           If you say yes here you get support for the RTC on the
 989           DaVinci platforms (DM365).
 990
 991           This driver can also be built as a module. If so, the module
 992           will be called rtc-davinci.
 993
 994 config RTC_DRV_IMXDI
 995         tristate "Freescale IMX DryIce Real Time Clock"
 996         depends on ARCH_MXC
 997         help
 998            Support for Freescale IMX DryIce RTC
 999
1000            This driver can also be built as a module, if so, the module
1001            will be called "rtc-imxdi".
1002
1003 config RTC_DRV_OMAP
1004         tristate "TI OMAP1"
1005         depends on ARCH_OMAP15XX || ARCH_OMAP16XX || ARCH_OMAP730 || ARCH_DAVINCI_DA8XX || SOC_AM33XX
1006         help
1007           Say "yes" here to support the on chip real time clock
1008           present on TI OMAP1, AM33xx and DA8xx/OMAP-L13x.
1009
1010           This driver can also be built as a module, if so, module
1011           will be called rtc-omap.
1012
1013 config HAVE_S3C_RTC
1014         bool
1015         help
1016           This will include RTC support for Samsung SoCs. If
1017           you want to include RTC support for any machine, kindly
1018           select this in the respective mach-XXXX/Kconfig file.
1019
1020 config RTC_DRV_S3C
1021         tristate "Samsung S3C series SoC RTC"
1022         depends on ARCH_S3C64XX || HAVE_S3C_RTC
1023         help
1024           RTC (Realtime Clock) driver for the clock inbuilt into the
1025           Samsung S3C24XX series of SoCs. This can provide periodic
1026           interrupt rates from 1Hz to 64Hz for user programs, and
1027           wakeup from Alarm.
1028
1029           The driver currently supports the common features on all the
1030           S3C24XX range, such as the S3C2410, S3C2412, S3C2413, S3C2440
1031           and S3C2442.
1032
1033           This driver can also be build as a module. If so, the module
1034           will be called rtc-s3c.
1035
1036 config RTC_DRV_EP93XX
1037         tristate "Cirrus Logic EP93XX"
1038         depends on ARCH_EP93XX
1039         help
1040           If you say yes here you get support for the
1041           RTC embedded in the Cirrus Logic EP93XX processors.
1042
1043           This driver can also be built as a module. If so, the module
1044           will be called rtc-ep93xx.
1045
1046 config RTC_DRV_SA1100
1047         tristate "SA11x0/PXA2xx/PXA910"
1048         depends on ARCH_SA1100 || ARCH_PXA || ARCH_MMP
1049         help
1050           If you say Y here you will get access to the real time clock
1051           built into your SA11x0 or PXA2xx CPU.
1052
1053           To compile this driver as a module, choose M here: the
1054           module will be called rtc-sa1100.
1055
1056 config RTC_DRV_SH
1057         tristate "SuperH On-Chip RTC"
1058         depends on SUPERH && HAVE_CLK
1059         help
1060           Say Y here to enable support for the on-chip RTC found in
1061           most SuperH processors.
1062
1063           To compile this driver as a module, choose M here: the
1064           module will be called rtc-sh.
1065
1066 config RTC_DRV_VR41XX
1067         tristate "NEC VR41XX"
1068         depends on CPU_VR41XX
1069         help
1070           If you say Y here you will get access to the real time clock
1071           built into your NEC VR41XX CPU.
1072
1073           To compile this driver as a module, choose M here: the
1074           module will be called rtc-vr41xx.
1075
1076 config RTC_DRV_PL030
1077         tristate "ARM AMBA PL030 RTC"
1078         depends on ARM_AMBA
1079         help
1080           If you say Y here you will get access to ARM AMBA
1081           PrimeCell PL030 RTC found on certain ARM SOCs.
1082
1083           To compile this driver as a module, choose M here: the
1084           module will be called rtc-pl030.
1085
1086 config RTC_DRV_PL031
1087         tristate "ARM AMBA PL031 RTC"
1088         depends on ARM_AMBA
1089         help
1090           If you say Y here you will get access to ARM AMBA
1091           PrimeCell PL031 RTC found on certain ARM SOCs.
1092
1093           To compile this driver as a module, choose M here: the
1094           module will be called rtc-pl031.
1095
1096 config RTC_DRV_AT32AP700X
1097         tristate "AT32AP700X series RTC"
1098         depends on PLATFORM_AT32AP
1099         help
1100           Driver for the internal RTC (Realtime Clock) on Atmel AVR32
1101           AT32AP700x family processors.
1102
1103 config RTC_DRV_AT91RM9200
1104         tristate "AT91RM9200 or some AT91SAM9 RTC"
1105         depends on ARCH_AT91
1106         help
1107           Driver for the internal RTC (Realtime Clock) module found on
1108           Atmel AT91RM9200's and some  AT91SAM9 chips. On AT91SAM9 chips
1109           this is powered by the backup power supply.
1110
1111 config RTC_DRV_AT91SAM9
1112         tristate "AT91SAM9 RTT as RTC"
1113         depends on ARCH_AT91 && !ARCH_AT91RM9200
1114         select MFD_SYSCON
1115         help
1116           Some AT91SAM9 SoCs provide an RTT (Real Time Timer) block which
1117           can be used as an RTC thanks to the backup power supply (e.g. a
1118           small coin cell battery) which keeps this block and the GPBR
1119           (General Purpose Backup Registers) block powered when the device
1120           is shutdown.
1121           Some AT91SAM9 SoCs provide a real RTC block, on those ones you'd
1122           probably want to use the real RTC block instead of the "RTT as an
1123           RTC" driver.
1124
1125 config RTC_DRV_AT91SAM9_RTT
1126         int
1127         range 0 1
1128         default 0
1129         prompt "RTT module Number" if ARCH_AT91SAM9263
1130         depends on RTC_DRV_AT91SAM9
1131         help
1132           This option is only relevant for legacy board support and
1133           won't be used when booting a DT board.
1134
1135           More than one RTT module is available. You can choose which
1136           one will be used as an RTC. The default of zero is normally
1137           OK to use, though some systems use that for non-RTC purposes.
1138
1139 config RTC_DRV_AT91SAM9_GPBR
1140         int
1141         range 0 3 if !ARCH_AT91SAM9263
1142         range 0 15 if ARCH_AT91SAM9263
1143         default 0
1144         prompt "Backup Register Number"
1145         depends on RTC_DRV_AT91SAM9
1146         help
1147           This option is only relevant for legacy board support and
1148           won't be used when booting a DT board.
1149
1150           The RTC driver needs to use one of the General Purpose Backup
1151           Registers (GPBRs) as well as the RTT. You can choose which one
1152           will be used. The default of zero is normally OK to use, but
1153           on some systems other software needs to use that register.
1154
1155 config RTC_DRV_AU1XXX
1156         tristate "Au1xxx Counter0 RTC support"
1157         depends on MIPS_ALCHEMY
1158         help
1159           This is a driver for the Au1xxx on-chip Counter0 (Time-Of-Year
1160           counter) to be used as a RTC.
1161
1162           This driver can also be built as a module. If so, the module
1163           will be called rtc-au1xxx.
1164
1165 config RTC_DRV_BFIN
1166         tristate "Blackfin On-Chip RTC"
1167         depends on BLACKFIN && !BF561
1168         help
1169           If you say yes here you will get support for the
1170           Blackfin On-Chip Real Time Clock.
1171
1172           This driver can also be built as a module. If so, the module
1173           will be called rtc-bfin.
1174
1175 config RTC_DRV_RS5C313
1176         tristate "Ricoh RS5C313"
1177         depends on SH_LANDISK
1178         help
1179           If you say yes here you get support for the Ricoh RS5C313 RTC chips.
1180
1181 config RTC_DRV_GENERIC
1182         tristate "Generic RTC support"
1183         # Please consider writing a new RTC driver instead of using the generic
1184         # RTC abstraction
1185         depends on PARISC || M68K || PPC || SUPERH32
1186         help
1187           Say Y or M here to enable RTC support on systems using the generic
1188           RTC abstraction. If you do not know what you are doing, you should
1189           just say Y.
1190
1191 config RTC_DRV_PXA
1192        tristate "PXA27x/PXA3xx"
1193        depends on ARCH_PXA
1194        help
1195          If you say Y here you will get access to the real time clock
1196          built into your PXA27x or PXA3xx CPU.
1197
1198          This RTC driver uses PXA RTC registers available since pxa27x
1199          series (RDxR, RYxR) instead of legacy RCNR, RTAR.
1200
1201 config RTC_DRV_VT8500
1202         tristate "VIA/WonderMedia 85xx SoC RTC"
1203         depends on ARCH_VT8500
1204         help
1205           If you say Y here you will get access to the real time clock
1206           built into your VIA VT8500 SoC or its relatives.
1207
1208
1209 config RTC_DRV_SUN4V
1210         bool "SUN4V Hypervisor RTC"
1211         depends on SPARC64
1212         help
1213           If you say Y here you will get support for the Hypervisor
1214           based RTC on SUN4V systems.
1215
1216 config RTC_DRV_SUN6I
1217         tristate "Allwinner A31 RTC"
1218         depends on MACH_SUN6I || MACH_SUN8I
1219         help
1220           If you say Y here you will get support for the RTC found on
1221           Allwinner A31.
1222
1223 config RTC_DRV_SUNXI
1224         tristate "Allwinner sun4i/sun7i RTC"
1225         depends on MACH_SUN4I || MACH_SUN7I
1226         help
1227           If you say Y here you will get support for the RTC found on
1228           Allwinner A10/A20.
1229
1230 config RTC_DRV_STARFIRE
1231         bool "Starfire RTC"
1232         depends on SPARC64
1233         help
1234           If you say Y here you will get support for the RTC found on
1235           Starfire systems.
1236
1237 config RTC_DRV_TX4939
1238         tristate "TX4939 SoC"
1239         depends on SOC_TX4939
1240         help
1241           Driver for the internal RTC (Realtime Clock) module found on
1242           Toshiba TX4939 SoC.
1243
1244 config RTC_DRV_MV
1245         tristate "Marvell SoC RTC"
1246         depends on ARCH_DOVE || ARCH_MVEBU
1247         help
1248           If you say yes here you will get support for the in-chip RTC
1249           that can be found in some of Marvell's SoC devices, such as
1250           the Kirkwood 88F6281 and 88F6192.
1251
1252           This driver can also be built as a module. If so, the module
1253           will be called rtc-mv.
1254
1255 config RTC_DRV_PS3
1256         tristate "PS3 RTC"
1257         depends on PPC_PS3
1258         help
1259           If you say yes here you will get support for the RTC on PS3.
1260
1261           This driver can also be built as a module. If so, the module
1262           will be called rtc-ps3.
1263
1264 config RTC_DRV_COH901331
1265         tristate "ST-Ericsson COH 901 331 RTC"
1266         depends on ARCH_U300
1267         help
1268           If you say Y here you will get access to ST-Ericsson
1269           COH 901 331 RTC clock found in some ST-Ericsson Mobile
1270           Platforms.
1271
1272           This driver can also be built as a module. If so, the module
1273           will be called "rtc-coh901331".
1274
1275
1276 config RTC_DRV_STMP
1277         tristate "Freescale STMP3xxx/i.MX23/i.MX28 RTC"
1278         depends on ARCH_MXS
1279         help
1280           If you say yes here you will get support for the onboard
1281           STMP3xxx/i.MX23/i.MX28 RTC.
1282
1283           This driver can also be built as a module. If so, the module
1284           will be called rtc-stmp3xxx.
1285
1286 config RTC_DRV_PCAP
1287         tristate "PCAP RTC"
1288         depends on EZX_PCAP
1289         help
1290           If you say Y here you will get support for the RTC found on
1291           the PCAP2 ASIC used on some Motorola phones.
1292
1293 config RTC_DRV_MC13XXX
1294         depends on MFD_MC13XXX
1295         tristate "Freescale MC13xxx RTC"
1296         help
1297           This enables support for the RTCs found on Freescale's PMICs
1298           MC13783 and MC13892.
1299
1300 config RTC_DRV_MPC5121
1301         tristate "Freescale MPC5121 built-in RTC"
1302         depends on PPC_MPC512x || PPC_MPC52xx
1303         help
1304           If you say yes here you will get support for the
1305           built-in RTC on MPC5121 or on MPC5200.
1306
1307           This driver can also be built as a module. If so, the module
1308           will be called rtc-mpc5121.
1309
1310 config RTC_DRV_JZ4740
1311         tristate "Ingenic JZ4740 SoC"
1312         depends on MACH_JZ4740
1313         help
1314           If you say yes here you get support for the Ingenic JZ4740 SoC RTC
1315           controller.
1316
1317           This driver can also be buillt as a module. If so, the module
1318           will be called rtc-jz4740.
1319
1320 config RTC_DRV_LPC32XX
1321         depends on ARCH_LPC32XX
1322         tristate "NXP LPC32XX RTC"
1323         help
1324           This enables support for the NXP RTC in the LPC32XX
1325
1326           This driver can also be buillt as a module. If so, the module
1327           will be called rtc-lpc32xx.
1328
1329 config RTC_DRV_PM8XXX
1330         tristate "Qualcomm PMIC8XXX RTC"
1331         depends on MFD_PM8XXX || MFD_SPMI_PMIC
1332         help
1333           If you say yes here you get support for the
1334           Qualcomm PMIC8XXX RTC.
1335
1336           To compile this driver as a module, choose M here: the
1337           module will be called rtc-pm8xxx.
1338
1339 config RTC_DRV_TEGRA
1340         tristate "NVIDIA Tegra Internal RTC driver"
1341         depends on ARCH_TEGRA
1342         help
1343           If you say yes here you get support for the
1344           Tegra 200 series internal RTC module.
1345
1346           This drive can also be built as a module. If so, the module
1347           will be called rtc-tegra.
1348
1349 config RTC_DRV_TILE
1350         tristate "Tilera hypervisor RTC support"
1351         depends on TILE
1352         help
1353           Enable support for the Linux driver side of the Tilera
1354           hypervisor's real-time clock interface.
1355
1356 config RTC_DRV_PUV3
1357         tristate "PKUnity v3 RTC support"
1358         depends on ARCH_PUV3
1359         help
1360           This enables support for the RTC in the PKUnity-v3 SoCs.
1361
1362           This drive can also be built as a module. If so, the module
1363           will be called rtc-puv3.
1364
1365 config RTC_DRV_LOONGSON1
1366         tristate "loongson1 RTC support"
1367         depends on MACH_LOONGSON1
1368         help
1369           This is a driver for the loongson1 on-chip Counter0 (Time-Of-Year
1370           counter) to be used as a RTC.
1371
1372           This driver can also be built as a module. If so, the module
1373           will be called rtc-ls1x.
1374
1375 config RTC_DRV_MXC
1376         tristate "Freescale MXC Real Time Clock"
1377         depends on ARCH_MXC
1378         help
1379            If you say yes here you get support for the Freescale MXC
1380            RTC module.
1381
1382            This driver can also be built as a module, if so, the module
1383            will be called "rtc-mxc".
1384
1385 config RTC_DRV_SNVS
1386         tristate "Freescale SNVS RTC support"
1387         depends on HAS_IOMEM
1388         depends on OF
1389         help
1390            If you say yes here you get support for the Freescale SNVS
1391            Low Power (LP) RTC module.
1392
1393            This driver can also be built as a module, if so, the module
1394            will be called "rtc-snvs".
1395
1396 config RTC_DRV_SIRFSOC
1397         tristate "SiRFSOC RTC"
1398         depends on ARCH_SIRF
1399         help
1400           Say "yes" here to support the real time clock on SiRF SOC chips.
1401           This driver can also be built as a module called rtc-sirfsoc.
1402
1403 config RTC_DRV_MOXART
1404         tristate "MOXA ART RTC"
1405         depends on ARCH_MOXART || COMPILE_TEST
1406         help
1407            If you say yes here you get support for the MOXA ART
1408            RTC module.
1409
1410            This driver can also be built as a module. If so, the module
1411            will be called rtc-moxart
1412
1413 config RTC_DRV_XGENE
1414         tristate "APM X-Gene RTC"
1415         depends on HAS_IOMEM
1416         help
1417           If you say yes here you get support for the APM X-Gene SoC real time
1418           clock.
1419
1420           This driver can also be built as a module, if so, the module
1421           will be called "rtc-xgene".
1422
1423 comment "HID Sensor RTC drivers"
1424
1425 config RTC_DRV_HID_SENSOR_TIME
1426         tristate "HID Sensor Time"
1427         depends on USB_HID
1428         select IIO
1429         select HID_SENSOR_HUB
1430         select HID_SENSOR_IIO_COMMON
1431         help
1432           Say yes here to build support for the HID Sensors of type Time.
1433           This drivers makes such sensors available as RTCs.
1434
1435           If this driver is compiled as a module, it will be named
1436           rtc-hid-sensor-time.
1437
1438
1439 endif # RTC_CLASS