drivers/net/hamradio/Kconfig

   1 config MKISS
   2         tristate "Serial port KISS driver"
   3         depends on AX25 && TTY
   4         select CRC16
   5         ---help---
   6           KISS is a protocol used for the exchange of data between a computer
   7           and a Terminal Node Controller (a small embedded system commonly
   8           used for networking over AX.25 amateur radio connections; it
   9           connects the computer's serial port with the radio's microphone
  10           input and speaker output).
  11
  12           Although KISS is less advanced than the 6pack protocol, it has
  13           the advantage that it is already supported by most modern TNCs
  14           without the need for a firmware upgrade.
  15
  16           To compile this driver as a module, choose M here: the module
  17           will be called mkiss.
  18
  19 config 6PACK
  20         tristate "Serial port 6PACK driver"
  21         depends on AX25 && TTY
  22         ---help---
  23           6pack is a transmission protocol for the data exchange between your
  24           PC and your TNC (the Terminal Node Controller acts as a kind of
  25           modem connecting your computer's serial port to your radio's
  26           microphone input and speaker output). This protocol can be used as
  27           an alternative to KISS for networking over AX.25 amateur radio
  28           connections, but it has some extended functionality.
  29
  30           Note that this driver is still experimental and might cause
  31           problems. For details about the features and the usage of the
  32           driver, read <file:Documentation/networking/6pack.txt>.
  33
  34           To compile this driver as a module, choose M here: the module
  35           will be called 6pack.
  36
  37 config BPQETHER
  38         tristate "BPQ Ethernet driver"
  39         depends on AX25
  40         help
  41           AX.25 is the protocol used for computer communication over amateur
  42           radio. If you say Y here, you will be able to send and receive AX.25
  43           traffic over Ethernet (also called "BPQ AX.25"), which could be
  44           useful if some other computer on your local network has a direct
  45           amateur radio connection.
  46
  47 config DMASCC
  48         tristate "High-speed (DMA) SCC driver for AX.25"
  49         depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API
  50         ---help---
  51           This is a driver for high-speed SCC boards, i.e. those supporting
  52           DMA on one port. You usually use those boards to connect your
  53           computer to an amateur radio modem (such as the WA4DSY 56kbps
  54           modem), in order to send and receive AX.25 packet radio network
  55           traffic.
  56
  57           Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
  58           PackeTwin, and S5SCC/DMA boards. They are detected automatically.
  59           If you have one of these cards, say Y here and read the AX25-HOWTO,
  60           available from <http://www.tldp.org/docs.html#howto>.
  61
  62           This driver can operate multiple boards simultaneously. If you
  63           compile it as a module (by saying M instead of Y), it will be called
  64           dmascc. If you don't pass any parameter to the driver, all
  65           possible I/O addresses are probed. This could irritate other devices
  66           that are currently not in use. You may specify the list of addresses
  67           to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the
  68           kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
  69           network interfaces will be called dmascc0 and dmascc1 for the board
  70           detected first, dmascc2 and dmascc3 for the second one, and so on.
  71
  72           Before you configure each interface with ifconfig, you MUST set
  73           certain parameters, such as channel access timing, clock mode, and
  74           DMA channel. This is accomplished with a small utility program,
  75           dmascc_cfg, available at
  76           <http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to
  77           get at least version 1.27 of dmascc_cfg, as older versions will not
  78           work with the current driver.
  79
  80 config SCC
  81         tristate "Z8530 SCC driver"
  82         depends on ISA && AX25 && ISA_DMA_API
  83         ---help---
  84           These cards are used to connect your Linux box to an amateur radio
  85           in order to communicate with other computers. If you want to use
  86           this, read <file:Documentation/networking/z8530drv.txt> and the
  87           AX25-HOWTO, available from
  88           <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
  89           to "Amateur Radio AX.25 Level 2" support.
  90
  91           To compile this driver as a module, choose M here: the module
  92           will be called scc.
  93
  94 config SCC_DELAY
  95         bool "additional delay for PA0HZP OptoSCC compatible boards"
  96         depends on SCC
  97         help
  98           Say Y here if you experience problems with the SCC driver not
  99           working properly; please read
 100           <file:Documentation/networking/z8530drv.txt> for details.
 101
 102           If unsure, say N.
 103
 104 config SCC_TRXECHO
 105         bool "support for TRX that feedback the tx signal to rx"
 106         depends on SCC
 107         help
 108           Some transmitters feed the transmitted signal back to the receive
 109           line.  Say Y here to foil this by explicitly disabling the receiver
 110           during data transmission.
 111
 112           If in doubt, say Y.
 113
 114 config BAYCOM_SER_FDX
 115         tristate "BAYCOM ser12 fullduplex driver for AX.25"
 116         depends on AX25 && !S390
 117         select CRC_CCITT
 118         ---help---
 119           This is one of two drivers for Baycom style simple amateur radio
 120           modems that connect to a serial interface. The driver supports the
 121           ser12 design in full-duplex mode. In addition, it allows the
 122           baudrate to be set between 300 and 4800 baud (however not all modems
 123           support all baudrates). This is the preferred driver. The next
 124           driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
 125           driver and still provided in case this driver does not work with
 126           your serial interface chip. To configure the driver, use the sethdlc
 127           utility available in the standard ax25 utilities package. For
 128           information on the modems, see <http://www.baycom.de/> and
 129           <file:Documentation/networking/baycom.txt>.
 130
 131           To compile this driver as a module, choose M here: the module
 132           will be called baycom_ser_fdx.  This is recommended.
 133
 134 config BAYCOM_SER_HDX
 135         tristate "BAYCOM ser12 halfduplex driver for AX.25"
 136         depends on AX25 && !S390
 137         select CRC_CCITT
 138         ---help---
 139           This is one of two drivers for Baycom style simple amateur radio
 140           modems that connect to a serial interface. The driver supports the
 141           ser12 design in half-duplex mode. This is the old driver.  It is
 142           still provided in case your serial interface chip does not work with
 143           the full-duplex driver. This driver is deprecated.  To configure
 144           the driver, use the sethdlc utility available in the standard ax25
 145           utilities package. For information on the modems, see
 146           <http://www.baycom.de/> and
 147           <file:Documentation/networking/baycom.txt>.
 148
 149           To compile this driver as a module, choose M here: the module
 150           will be called baycom_ser_hdx.  This is recommended.
 151
 152 config BAYCOM_PAR
 153         tristate "BAYCOM picpar and par96 driver for AX.25"
 154         depends on PARPORT && AX25
 155         select CRC_CCITT
 156         ---help---
 157           This is a driver for Baycom style simple amateur radio modems that
 158           connect to a parallel interface. The driver supports the picpar and
 159           par96 designs. To configure the driver, use the sethdlc utility
 160           available in the standard ax25 utilities package. For information on
 161           the modems, see <http://www.baycom.de/> and the file
 162           <file:Documentation/networking/baycom.txt>.
 163
 164           To compile this driver as a module, choose M here: the module
 165           will be called baycom_par.  This is recommended.
 166
 167 config BAYCOM_EPP
 168         tristate "BAYCOM epp driver for AX.25"
 169         depends on PARPORT && AX25 && !64BIT
 170         select CRC_CCITT
 171         ---help---
 172           This is a driver for Baycom style simple amateur radio modems that
 173           connect to a parallel interface. The driver supports the EPP
 174           designs. To configure the driver, use the sethdlc utility available
 175           in the standard ax25 utilities package. For information on the
 176           modems, see <http://www.baycom.de/> and the file
 177           <file:Documentation/networking/baycom.txt>.
 178
 179           To compile this driver as a module, choose M here: the module
 180           will be called baycom_epp.  This is recommended.
 181
 182 config YAM
 183         tristate "YAM driver for AX.25"
 184         depends on AX25 && !S390
 185         help
 186           The YAM is a modem for packet radio which connects to the serial
 187           port and includes some of the functions of a Terminal Node
 188           Controller. If you have one of those, say Y here.
 189
 190           To compile this driver as a module, choose M here: the module
 191           will be called yam.
 192
 193