2 # Input misc drivers configuration
5 bool "Miscellaneous devices"
7 Say Y here, and a list of miscellaneous input drivers will be displayed.
8 Everything that didn't fit into the other categories is here. This option
9 doesn't affect the kernel.
15 config INPUT_88PM860X_ONKEY
16 tristate "88PM860x ONKEY support"
17 depends on MFD_88PM860X
19 Support the ONKEY of Marvell 88PM860x PMICs as an input device
20 reporting power button status.
22 To compile this driver as a module, choose M here: the module
23 will be called 88pm860x_onkey.
25 config INPUT_88PM80X_ONKEY
26 tristate "88PM80x ONKEY support"
27 depends on MFD_88PM800
29 Support the ONKEY of Marvell 88PM80x PMICs as an input device
30 reporting power button status.
32 To compile this driver as a module, choose M here: the module
33 will be called 88pm80x_onkey.
35 config INPUT_AB8500_PONKEY
36 tristate "AB8500 Pon (PowerOn) Key"
37 depends on AB8500_CORE
39 Say Y here to use the PowerOn Key for ST-Ericsson's AB8500
42 To compile this driver as a module, choose M here: the module
43 will be called ab8500-ponkey.
46 tristate "Analog Devices AD714x Capacitance Touch Sensor"
48 Say Y here if you want to support an AD7142/3/7/8/7A touch sensor.
50 You should select a bus connection too.
52 To compile this driver as a module, choose M here: the
53 module will be called ad714x.
55 config INPUT_AD714X_I2C
56 tristate "support I2C bus connection"
57 depends on INPUT_AD714X && I2C
60 Say Y here if you have AD7142/AD7147 hooked to an I2C bus.
62 To compile this driver as a module, choose M here: the
63 module will be called ad714x-i2c.
65 config INPUT_AD714X_SPI
66 tristate "support SPI bus connection"
67 depends on INPUT_AD714X && SPI
70 Say Y here if you have AD7142/AD7147 hooked to a SPI bus.
72 To compile this driver as a module, choose M here: the
73 module will be called ad714x-spi.
75 config INPUT_ARIZONA_HAPTICS
76 tristate "Arizona haptics support"
77 depends on MFD_ARIZONA && SND_SOC
78 select INPUT_FF_MEMLESS
80 Say Y to enable support for the haptics module in Arizona CODECs.
82 To compile this driver as a module, choose M here: the
83 module will be called arizona-haptics.
85 config INPUT_ATMEL_CAPTOUCH
86 tristate "Atmel Capacitive Touch Button Driver"
87 depends on OF || COMPILE_TEST
90 Say Y here if an Atmel Capacitive Touch Button device which
91 implements "captouch" protocol is connected to I2C bus. Typically
92 this device consists of Atmel Touch sensor controlled by AtMegaXX
93 MCU running firmware based on Qtouch library.
94 One should find "atmel,captouch" node in the board specific DTS.
96 To compile this driver as a module, choose M here: the
97 module will be called atmel_captouch.
100 tristate "BMA150/SMB380 acceleration sensor support"
104 Say Y here if you have Bosch Sensortec's BMA150 or SMB380
105 acceleration sensor hooked to an I2C bus.
107 To compile this driver as a module, choose M here: the
108 module will be called bma150.
110 config INPUT_E3X0_BUTTON
111 tristate "NI Ettus Research USRP E3xx Button support."
114 Say Y here to enable support for the NI Ettus Research
117 To compile this driver as a module, choose M here: the
118 module will be called e3x0_button.
121 tristate "PC Speaker support"
122 depends on PCSPKR_PLATFORM
124 Say Y here if you want the standard PC Speaker to be used for
129 To compile this driver as a module, choose M here: the
130 module will be called pcspkr.
132 config INPUT_PM8941_PWRKEY
133 tristate "Qualcomm PM8941 power key support"
134 depends on MFD_SPMI_PMIC
136 Say Y here if you want support for the power key usually found
137 on boards using a Qualcomm PM8941 compatible PMIC.
141 To compile this driver as a module, choose M here: the module
142 will be called pm8941-pwrkey.
144 config INPUT_PM8XXX_VIBRATOR
145 tristate "Qualcomm PM8XXX vibrator support"
146 depends on MFD_PM8XXX || MFD_SPMI_PMIC
147 select INPUT_FF_MEMLESS
149 This option enables device driver support for the vibrator
150 on Qualcomm PM8xxx chip. This driver supports ff-memless interface
151 from input framework.
153 To compile this driver as module, choose M here: the
154 module will be called pm8xxx-vibrator.
156 config INPUT_PMIC8XXX_PWRKEY
157 tristate "PMIC8XXX power key support"
158 depends on MFD_PM8XXX
160 Say Y here if you want support for the PMIC8XXX power key.
164 To compile this driver as a module, choose M here: the
165 module will be called pmic8xxx-pwrkey.
167 config INPUT_SPARCSPKR
168 tristate "SPARC Speaker support"
169 depends on PCI && SPARC64
171 Say Y here if you want the standard Speaker on Sparc PCI systems
172 to be used for bells and whistles.
176 To compile this driver as a module, choose M here: the
177 module will be called sparcspkr.
179 config INPUT_M68K_BEEP
180 tristate "M68k Beeper support"
183 config INPUT_MAX77693_HAPTIC
184 tristate "MAXIM MAX77693/MAX77843 haptic controller support"
185 depends on (MFD_MAX77693 || MFD_MAX77843) && PWM
186 select INPUT_FF_MEMLESS
188 This option enables support for the haptic controller on
189 MAXIM MAX77693 and MAX77843 chips.
191 To compile this driver as module, choose M here: the
192 module will be called max77693-haptic.
194 config INPUT_MAX8925_ONKEY
195 tristate "MAX8925 ONKEY support"
196 depends on MFD_MAX8925
198 Support the ONKEY of MAX8925 PMICs as an input device
199 reporting power button status.
201 To compile this driver as a module, choose M here: the module
202 will be called max8925_onkey.
204 config INPUT_MAX8997_HAPTIC
205 tristate "MAXIM MAX8997 haptic controller support"
206 depends on PWM && MFD_MAX8997
207 select INPUT_FF_MEMLESS
209 This option enables device driver support for the haptic controller
210 on MAXIM MAX8997 chip. This driver supports ff-memless interface
211 from input framework.
213 To compile this driver as module, choose M here: the
214 module will be called max8997-haptic.
216 config INPUT_MC13783_PWRBUTTON
217 tristate "MC13783 ON buttons"
218 depends on MFD_MC13XXX
220 Support the ON buttons of MC13783 PMIC as an input device
221 reporting power button status.
223 To compile this driver as a module, choose M here: the module
224 will be called mc13783-pwrbutton.
227 tristate "MMA8450 - Freescale's 3-Axis, 8/12-bit Digital Accelerometer"
231 Say Y here if you want to support Freescale's MMA8450 Accelerometer
232 through I2C interface.
234 To compile this driver as a module, choose M here: the
235 module will be called mma8450.
238 tristate "Fujitsu Lifebook Application Panel buttons"
239 depends on X86 && I2C && LEDS_CLASS
241 select CHECK_SIGNATURE
243 Say Y here for support of the Application Panel buttons, used on
244 Fujitsu Lifebook. These are attached to the mainboard through
245 an SMBus interface managed by the I2C Intel ICH (i801) driver,
246 which you should also build for this kernel.
248 To compile this driver as a module, choose M here: the module will
252 tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
254 depends on GPIOLIB || COMPILE_TEST
256 Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
257 hooked to an I2C bus.
259 To compile this driver as a module, choose M here: the
260 module will be called gp2ap002a00f.
262 config INPUT_GPIO_BEEPER
263 tristate "Generic GPIO Beeper support"
264 depends on GPIOLIB || COMPILE_TEST
266 Say Y here if you have a beeper connected to a GPIO pin.
268 To compile this driver as a module, choose M here: the
269 module will be called gpio-beeper.
271 config INPUT_GPIO_TILT_POLLED
272 tristate "Polled GPIO tilt switch"
273 depends on GPIOLIB || COMPILE_TEST
276 This driver implements support for tilt switches connected
277 to GPIO pins that are not capable of generating interrupts.
279 The list of gpios to use and the mapping of their states
280 to specific angles is done via platform data.
282 To compile this driver as a module, choose M here: the
283 module will be called gpio_tilt_polled.
285 config INPUT_GPIO_DECODER
286 tristate "Polled GPIO Decoder Input driver"
287 depends on GPIOLIB || COMPILE_TEST
290 Say Y here if you want driver to read status of multiple GPIO
291 lines and report the encoded value as an absolute integer to
294 To compile this driver as a module, choose M here: the module
295 will be called gpio_decoder.
297 config INPUT_IXP4XX_BEEPER
298 tristate "IXP4XX Beeper support"
299 depends on ARCH_IXP4XX
301 If you say yes here, you can connect a beeper to the
302 ixp4xx gpio pins. This is used by the LinkSys NSLU2.
306 To compile this driver as a module, choose M here: the
307 module will be called ixp4xx-beeper.
309 config INPUT_COBALT_BTNS
310 tristate "Cobalt button interface"
311 depends on MIPS_COBALT
314 Say Y here if you want to support MIPS Cobalt button interface.
316 To compile this driver as a module, choose M here: the
317 module will be called cobalt_btns.
319 config INPUT_CPCAP_PWRBUTTON
320 tristate "CPCAP OnKey"
323 Say Y here if you want to enable power key reporting via the
326 To compile this driver as a module, choose M here. The module will
327 be called cpcap-pwrbutton.
329 config INPUT_WISTRON_BTNS
330 tristate "x86 Wistron laptop button interface"
333 select INPUT_SPARSEKMAP
336 select CHECK_SIGNATURE
338 Say Y here for support of Wistron laptop button interfaces, used on
339 laptops of various brands, including Acer and Fujitsu-Siemens. If
340 available, mail and wifi LEDs will be controllable via /sys/class/leds.
342 To compile this driver as a module, choose M here: the module will
343 be called wistron_btns.
345 config INPUT_ATLAS_BTNS
346 tristate "x86 Atlas button interface"
347 depends on X86 && ACPI
349 Say Y here for support of Atlas wallmount touchscreen buttons.
350 The events will show up as scancodes F1 through F9 via evdev.
352 To compile this driver as a module, choose M here: the module will
353 be called atlas_btns.
355 config INPUT_ATI_REMOTE2
356 tristate "ATI / Philips USB RF remote control"
357 depends on USB_ARCH_HAS_HCD
360 Say Y here if you want to use an ATI or Philips USB RF remote control.
361 These are RF remotes with USB receivers.
362 ATI Remote Wonder II comes with some ATI's All-In-Wonder video cards
363 and is also available as a separate product.
364 This driver provides mouse pointer, left and right mouse buttons,
365 and maps all the other remote buttons to keypress events.
367 To compile this driver as a module, choose M here: the module will be
370 config INPUT_KEYSPAN_REMOTE
371 tristate "Keyspan DMR USB remote control"
372 depends on USB_ARCH_HAS_HCD
375 Say Y here if you want to use a Keyspan DMR USB remote control.
376 Currently only the UIA-11 type of receiver has been tested. The tag
377 on the receiver that connects to the USB port should have a P/N that
378 will tell you what type of DMR you have. The UIA-10 type is not
379 supported at this time. This driver maps all buttons to keypress
382 To compile this driver as a module, choose M here: the module will
383 be called keyspan_remote.
386 tristate "Kionix KXTJ9 tri-axis digital accelerometer"
389 Say Y here to enable support for the Kionix KXTJ9 digital tri-axis
392 To compile this driver as a module, choose M here: the module will
395 config INPUT_KXTJ9_POLLED_MODE
396 bool "Enable polling mode support"
397 depends on INPUT_KXTJ9
400 Say Y here if you need accelerometer to work in polling mode.
402 config INPUT_POWERMATE
403 tristate "Griffin PowerMate and Contour Jog support"
404 depends on USB_ARCH_HAS_HCD
407 Say Y here if you want to use Griffin PowerMate or Contour Jog devices.
408 These are aluminum dials which can measure clockwise and anticlockwise
409 rotation. The dial also acts as a pushbutton. The base contains an LED
410 which can be instructed to pulse or to switch to a particular intensity.
412 You can download userspace tools from
413 <http://sowerbutts.com/powermate/>.
415 To compile this driver as a module, choose M here: the
416 module will be called powermate.
419 tristate "Yealink usb-p1k voip phone"
420 depends on USB_ARCH_HAS_HCD
423 Say Y here if you want to enable keyboard and LCD functions of the
424 Yealink usb-p1k usb phones. The audio part is enabled by the generic
425 usb sound driver, so you might want to enable that as well.
427 For information about how to use these additional functions, see
428 <file:Documentation/input/yealink.txt>.
430 To compile this driver as a module, choose M here: the module will be
434 tristate "C-Media CM109 USB I/O Controller"
435 depends on USB_ARCH_HAS_HCD
438 Say Y here if you want to enable keyboard and buzzer functions of the
439 C-Media CM109 usb phones. The audio part is enabled by the generic
440 usb sound driver, so you might want to enable that as well.
442 To compile this driver as a module, choose M here: the module will be
445 config INPUT_REGULATOR_HAPTIC
446 tristate "Regulator haptics support"
448 select INPUT_FF_MEMLESS
450 This option enables device driver support for the haptic controlled
451 by a regulator. This driver supports ff-memless interface
452 from input framework.
454 To compile this driver as a module, choose M here: the
455 module will be called regulator-haptic.
457 config INPUT_RETU_PWRBUTTON
458 tristate "Retu Power button Driver"
461 Say Y here if you want to enable power key reporting via the
462 Retu chips found in Nokia Internet Tablets (770, N800, N810).
464 To compile this driver as a module, choose M here. The module will
465 be called retu-pwrbutton.
467 config INPUT_TPS65218_PWRBUTTON
468 tristate "TPS65218 Power button driver"
469 depends on (MFD_TPS65217 || MFD_TPS65218)
471 Say Y here if you want to enable power buttong reporting for
472 TPS65217 and TPS65218 Power Management IC devices.
474 To compile this driver as a module, choose M here. The module will
475 be called tps65218-pwrbutton.
477 config INPUT_AXP20X_PEK
478 tristate "X-Powers AXP20X power button driver"
479 depends on MFD_AXP20X
481 Say Y here if you want to enable power key reporting via the
484 To compile this driver as a module, choose M here. The module will
485 be called axp20x-pek.
488 config INPUT_TWL4030_PWRBUTTON
489 tristate "TWL4030 Power button Driver"
490 depends on TWL4030_CORE
492 Say Y here if you want to enable power key reporting via the
493 TWL4030 family of chips.
495 To compile this driver as a module, choose M here. The module will
496 be called twl4030_pwrbutton.
498 config INPUT_TWL4030_VIBRA
499 tristate "Support for TWL4030 Vibrator"
500 depends on TWL4030_CORE
501 select MFD_TWL4030_AUDIO
502 select INPUT_FF_MEMLESS
504 This option enables support for TWL4030 Vibrator Driver.
506 To compile this driver as a module, choose M here. The module will
507 be called twl4030_vibra.
509 config INPUT_TWL6040_VIBRA
510 tristate "Support for TWL6040 Vibrator"
511 depends on TWL6040_CORE
512 select INPUT_FF_MEMLESS
514 This option enables support for TWL6040 Vibrator Driver.
516 To compile this driver as a module, choose M here. The module will
517 be called twl6040_vibra.
520 tristate "User level driver support"
522 Say Y here if you want to support user level drivers for input
523 subsystem accessible under char device 10:223 - /dev/input/uinput.
525 To compile this driver as a module, choose M here: the
526 module will be called uinput.
528 config INPUT_SGI_BTNS
529 tristate "SGI Indy/O2 volume button interface"
530 depends on SGI_IP22 || SGI_IP32
533 Say Y here if you want to support SGI Indy/O2 volume button interface.
535 To compile this driver as a module, choose M here: the
536 module will be called sgi_btns.
539 tristate "HP SDC Real Time Clock"
540 depends on (GSC || HP300) && SERIO
543 Say Y here if you want to support the built-in real time clock
544 of the HP SDC controller.
546 config INPUT_PALMAS_PWRBUTTON
547 tristate "Palmas Power button Driver"
548 depends on MFD_PALMAS
550 Say Y here if you want to enable power key reporting via the
551 Palmas family of PMICs.
553 To compile this driver as a module, choose M here. The module will
554 be called palmas_pwrbutton.
556 config INPUT_PCF50633_PMU
557 tristate "PCF50633 PMU events"
558 depends on MFD_PCF50633
560 Say Y to include support for delivering PMU events via input
561 layer on NXP PCF50633.
564 tristate "PCF8574 Keypad input device"
567 Say Y here if you want to support a keypad connected via I2C
570 To compile this driver as a module, choose M here: the
571 module will be called pcf8574_keypad.
573 config INPUT_PWM_BEEPER
574 tristate "PWM beeper support"
577 Say Y here to get support for PWM based beeper devices.
581 To compile this driver as a module, choose M here: the module will be
584 config INPUT_RK805_PWRKEY
585 tristate "Rockchip RK805 PMIC power key support"
588 Select this option to enable power key driver for RK805.
592 To compile this driver as a module, choose M here: the module will be
595 config INPUT_GPIO_ROTARY_ENCODER
596 tristate "Rotary encoders connected to GPIO pins"
597 depends on GPIOLIB || COMPILE_TEST
599 Say Y here to add support for rotary encoders connected to GPIO lines.
600 Check file:Documentation/input/rotary-encoder.txt for more
603 To compile this driver as a module, choose M here: the
604 module will be called rotary_encoder.
606 config INPUT_RB532_BUTTON
607 tristate "Mikrotik Routerboard 532 button interface"
608 depends on MIKROTIK_RB532
612 Say Y here if you want support for the S1 button built into
613 Mikrotik's Routerboard 532.
615 To compile this driver as a module, choose M here: the
616 module will be called rb532_button.
618 config INPUT_DA9052_ONKEY
619 tristate "Dialog DA9052/DA9053 Onkey"
620 depends on PMIC_DA9052
622 Support the ONKEY of Dialog DA9052 PMICs as an input device
623 reporting power button status.
625 To compile this driver as a module, choose M here: the
626 module will be called da9052_onkey.
628 config INPUT_DA9055_ONKEY
629 tristate "Dialog Semiconductor DA9055 ONKEY"
630 depends on MFD_DA9055
632 Support the ONKEY of DA9055 PMICs as an input device
633 reporting power button status.
635 To compile this driver as a module, choose M here: the module
636 will be called da9055_onkey.
638 config INPUT_DA9063_ONKEY
639 tristate "Dialog DA9063/62/61 OnKey"
640 depends on MFD_DA9063 || MFD_DA9062
642 Support the ONKEY of Dialog DA9063, DA9062 and DA9061 Power
643 Management ICs as an input device capable of reporting the
646 To compile this driver as a module, choose M here: the module
647 will be called da9063_onkey.
649 config INPUT_DM355EVM
650 tristate "TI DaVinci DM355 EVM Keypad and IR Remote"
651 depends on MFD_DM355EVM_MSP
652 select INPUT_SPARSEKMAP
654 Supports the pushbuttons and IR remote used with
657 To compile this driver as a module, choose M here: the
658 module will be called dm355evm_keys.
660 config INPUT_BFIN_ROTARY
661 tristate "Blackfin Rotary support"
662 depends on BF54x || BF52x
664 Say Y here if you want to use the Blackfin Rotary.
666 To compile this driver as a module, choose M here: the
667 module will be called bfin-rotary.
669 config INPUT_WM831X_ON
670 tristate "WM831X ON pin"
671 depends on MFD_WM831X
673 Support the ON pin of WM831X PMICs as an input device
674 reporting power button status.
676 To compile this driver as a module, choose M here: the module
677 will be called wm831x_on.
680 tristate "Motorola EZX PCAP misc input events"
683 Say Y here if you want to use Power key and Headphone button
684 on Motorola EZX phones.
686 To compile this driver as a module, choose M here: the
687 module will be called pcap_keys.
690 tristate "Analog Devices ADXL34x Three-Axis Digital Accelerometer"
693 Say Y here if you have a Accelerometer interface using the
694 ADXL345/6 controller, and your board-specific initialization
695 code includes that in its table of devices.
697 This driver can use either I2C or SPI communication to the
698 ADXL345/6 controller. Select the appropriate method for
701 If unsure, say N (but it's safe to say "Y").
703 To compile this driver as a module, choose M here: the
704 module will be called adxl34x.
706 config INPUT_ADXL34X_I2C
707 tristate "support I2C bus connection"
708 depends on INPUT_ADXL34X && I2C
711 Say Y here if you have ADXL345/6 hooked to an I2C bus.
713 To compile this driver as a module, choose M here: the
714 module will be called adxl34x-i2c.
716 config INPUT_ADXL34X_SPI
717 tristate "support SPI bus connection"
718 depends on INPUT_ADXL34X && SPI
721 Say Y here if you have ADXL345/6 hooked to a SPI bus.
723 To compile this driver as a module, choose M here: the
724 module will be called adxl34x-spi.
727 tristate "IMS Passenger Control Unit driver"
729 depends on LEDS_CLASS
731 Say Y here if you have system with IMS Rave Passenger Control Unit.
733 To compile this driver as a module, choose M here: the module will be
737 tristate "VTI CMA3000 Tri-axis accelerometer"
739 Say Y here if you want to use VTI CMA3000_D0x Accelerometer
742 This driver currently only supports I2C interface to the
743 controller. Also select the I2C method.
747 To compile this driver as a module, choose M here: the
748 module will be called cma3000_d0x.
750 config INPUT_CMA3000_I2C
751 tristate "Support I2C bus connection"
752 depends on INPUT_CMA3000 && I2C
754 Say Y here if you want to use VTI CMA3000_D0x Accelerometer
755 through I2C interface.
757 To compile this driver as a module, choose M here: the
758 module will be called cma3000_d0x_i2c.
760 config INPUT_XEN_KBDDEV_FRONTEND
761 tristate "Xen virtual keyboard and mouse support"
764 select XEN_XENBUS_FRONTEND
766 This driver implements the front-end of the Xen virtual
767 keyboard and mouse device driver. It communicates with a back-end
770 To compile this driver as a module, choose M here: the
771 module will be called xen-kbdfront.
773 config INPUT_SIRFSOC_ONKEY
774 tristate "CSR SiRFSoC power on/off/suspend key support"
775 depends on ARCH_SIRF && OF
778 Say Y here if you want to support for the SiRFSoC power on/off/suspend key
779 in Linux, after you press the onkey, system will suspend.
783 config INPUT_IDEAPAD_SLIDEBAR
784 tristate "IdeaPad Laptop Slidebar"
786 depends on SERIO_I8042
788 Say Y here if you have an IdeaPad laptop with a slidebar.
790 To compile this driver as a module, choose M here: the
791 module will be called ideapad_slidebar.
793 config INPUT_SOC_BUTTON_ARRAY
794 tristate "Windows-compatible SoC Button Array"
795 depends on KEYBOARD_GPIO
797 Say Y here if you have a SoC-based tablet that originally
800 To compile this driver as a module, choose M here: the
801 module will be called soc_button_array.
803 config INPUT_DRV260X_HAPTICS
804 tristate "TI DRV260X haptics support"
805 depends on INPUT && I2C
806 depends on GPIOLIB || COMPILE_TEST
807 select INPUT_FF_MEMLESS
810 Say Y to enable support for the TI DRV260X haptics driver.
812 To compile this driver as a module, choose M here: the
813 module will be called drv260x-haptics.
815 config INPUT_DRV2665_HAPTICS
816 tristate "TI DRV2665 haptics support"
817 depends on INPUT && I2C
818 select INPUT_FF_MEMLESS
821 Say Y to enable support for the TI DRV2665 haptics driver.
823 To compile this driver as a module, choose M here: the
824 module will be called drv2665-haptics.
826 config INPUT_DRV2667_HAPTICS
827 tristate "TI DRV2667 haptics support"
828 depends on INPUT && I2C
829 select INPUT_FF_MEMLESS
832 Say Y to enable support for the TI DRV2667 haptics driver.
834 To compile this driver as a module, choose M here: the
835 module will be called drv2667-haptics.
837 config INPUT_HISI_POWERKEY
838 tristate "Hisilicon PMIC ONKEY support"
839 depends on ARCH_HISI || COMPILE_TEST
841 Say Y to enable support for PMIC ONKEY.
843 To compile this driver as a module, choose M here: the
844 module will be called hisi_powerkey.