net: add skb_recycle_check() to enable netdriver skb recycling
[GitHub/mt8127/android_kernel_alcatel_ttab.git] / drivers / char / synclink_gt.c
1 /*
2 * $Id: synclink_gt.c,v 4.50 2007/07/25 19:29:25 paulkf Exp $
3 *
4 * Device driver for Microgate SyncLink GT serial adapters.
5 *
6 * written by Paul Fulghum for Microgate Corporation
7 * paulkf@microgate.com
8 *
9 * Microgate and SyncLink are trademarks of Microgate Corporation
10 *
11 * This code is released under the GNU General Public License (GPL)
12 *
13 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
14 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
15 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
16 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
17 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
18 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
19 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
20 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
21 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
22 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
23 * OF THE POSSIBILITY OF SUCH DAMAGE.
24 */
25
26 /*
27 * DEBUG OUTPUT DEFINITIONS
28 *
29 * uncomment lines below to enable specific types of debug output
30 *
31 * DBGINFO information - most verbose output
32 * DBGERR serious errors
33 * DBGBH bottom half service routine debugging
34 * DBGISR interrupt service routine debugging
35 * DBGDATA output receive and transmit data
36 * DBGTBUF output transmit DMA buffers and registers
37 * DBGRBUF output receive DMA buffers and registers
38 */
39
40 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
41 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
42 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
43 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
44 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
45 //#define DBGTBUF(info) dump_tbufs(info)
46 //#define DBGRBUF(info) dump_rbufs(info)
47
48
49 #include <linux/module.h>
50 #include <linux/errno.h>
51 #include <linux/signal.h>
52 #include <linux/sched.h>
53 #include <linux/timer.h>
54 #include <linux/interrupt.h>
55 #include <linux/pci.h>
56 #include <linux/tty.h>
57 #include <linux/tty_flip.h>
58 #include <linux/serial.h>
59 #include <linux/major.h>
60 #include <linux/string.h>
61 #include <linux/fcntl.h>
62 #include <linux/ptrace.h>
63 #include <linux/ioport.h>
64 #include <linux/mm.h>
65 #include <linux/slab.h>
66 #include <linux/netdevice.h>
67 #include <linux/vmalloc.h>
68 #include <linux/init.h>
69 #include <linux/delay.h>
70 #include <linux/ioctl.h>
71 #include <linux/termios.h>
72 #include <linux/bitops.h>
73 #include <linux/workqueue.h>
74 #include <linux/hdlc.h>
75 #include <linux/synclink.h>
76
77 #include <asm/system.h>
78 #include <asm/io.h>
79 #include <asm/irq.h>
80 #include <asm/dma.h>
81 #include <asm/types.h>
82 #include <asm/uaccess.h>
83
84 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
85 #define SYNCLINK_GENERIC_HDLC 1
86 #else
87 #define SYNCLINK_GENERIC_HDLC 0
88 #endif
89
90 /*
91 * module identification
92 */
93 static char *driver_name = "SyncLink GT";
94 static char *driver_version = "$Revision: 4.50 $";
95 static char *tty_driver_name = "synclink_gt";
96 static char *tty_dev_prefix = "ttySLG";
97 MODULE_LICENSE("GPL");
98 #define MGSL_MAGIC 0x5401
99 #define MAX_DEVICES 32
100
101 static struct pci_device_id pci_table[] = {
102 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
103 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
104 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
105 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
106 {0,}, /* terminate list */
107 };
108 MODULE_DEVICE_TABLE(pci, pci_table);
109
110 static int init_one(struct pci_dev *dev,const struct pci_device_id *ent);
111 static void remove_one(struct pci_dev *dev);
112 static struct pci_driver pci_driver = {
113 .name = "synclink_gt",
114 .id_table = pci_table,
115 .probe = init_one,
116 .remove = __devexit_p(remove_one),
117 };
118
119 static bool pci_registered;
120
121 /*
122 * module configuration and status
123 */
124 static struct slgt_info *slgt_device_list;
125 static int slgt_device_count;
126
127 static int ttymajor;
128 static int debug_level;
129 static int maxframe[MAX_DEVICES];
130
131 module_param(ttymajor, int, 0);
132 module_param(debug_level, int, 0);
133 module_param_array(maxframe, int, NULL, 0);
134
135 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
136 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
137 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
138
139 /*
140 * tty support and callbacks
141 */
142 static struct tty_driver *serial_driver;
143
144 static int open(struct tty_struct *tty, struct file * filp);
145 static void close(struct tty_struct *tty, struct file * filp);
146 static void hangup(struct tty_struct *tty);
147 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
148
149 static int write(struct tty_struct *tty, const unsigned char *buf, int count);
150 static int put_char(struct tty_struct *tty, unsigned char ch);
151 static void send_xchar(struct tty_struct *tty, char ch);
152 static void wait_until_sent(struct tty_struct *tty, int timeout);
153 static int write_room(struct tty_struct *tty);
154 static void flush_chars(struct tty_struct *tty);
155 static void flush_buffer(struct tty_struct *tty);
156 static void tx_hold(struct tty_struct *tty);
157 static void tx_release(struct tty_struct *tty);
158
159 static int ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
160 static int read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
161 static int chars_in_buffer(struct tty_struct *tty);
162 static void throttle(struct tty_struct * tty);
163 static void unthrottle(struct tty_struct * tty);
164 static int set_break(struct tty_struct *tty, int break_state);
165
166 /*
167 * generic HDLC support and callbacks
168 */
169 #if SYNCLINK_GENERIC_HDLC
170 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
171 static void hdlcdev_tx_done(struct slgt_info *info);
172 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
173 static int hdlcdev_init(struct slgt_info *info);
174 static void hdlcdev_exit(struct slgt_info *info);
175 #endif
176
177
178 /*
179 * device specific structures, macros and functions
180 */
181
182 #define SLGT_MAX_PORTS 4
183 #define SLGT_REG_SIZE 256
184
185 /*
186 * conditional wait facility
187 */
188 struct cond_wait {
189 struct cond_wait *next;
190 wait_queue_head_t q;
191 wait_queue_t wait;
192 unsigned int data;
193 };
194 static void init_cond_wait(struct cond_wait *w, unsigned int data);
195 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
196 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
197 static void flush_cond_wait(struct cond_wait **head);
198
199 /*
200 * DMA buffer descriptor and access macros
201 */
202 struct slgt_desc
203 {
204 __le16 count;
205 __le16 status;
206 __le32 pbuf; /* physical address of data buffer */
207 __le32 next; /* physical address of next descriptor */
208
209 /* driver book keeping */
210 char *buf; /* virtual address of data buffer */
211 unsigned int pdesc; /* physical address of this descriptor */
212 dma_addr_t buf_dma_addr;
213 unsigned short buf_count;
214 };
215
216 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
217 #define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b))
218 #define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b))
219 #define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
220 #define desc_count(a) (le16_to_cpu((a).count))
221 #define desc_status(a) (le16_to_cpu((a).status))
222 #define desc_complete(a) (le16_to_cpu((a).status) & BIT15)
223 #define desc_eof(a) (le16_to_cpu((a).status) & BIT2)
224 #define desc_crc_error(a) (le16_to_cpu((a).status) & BIT1)
225 #define desc_abort(a) (le16_to_cpu((a).status) & BIT0)
226 #define desc_residue(a) ((le16_to_cpu((a).status) & 0x38) >> 3)
227
228 struct _input_signal_events {
229 int ri_up;
230 int ri_down;
231 int dsr_up;
232 int dsr_down;
233 int dcd_up;
234 int dcd_down;
235 int cts_up;
236 int cts_down;
237 };
238
239 /*
240 * device instance data structure
241 */
242 struct slgt_info {
243 void *if_ptr; /* General purpose pointer (used by SPPP) */
244 struct tty_port port;
245
246 struct slgt_info *next_device; /* device list link */
247
248 int magic;
249
250 char device_name[25];
251 struct pci_dev *pdev;
252
253 int port_count; /* count of ports on adapter */
254 int adapter_num; /* adapter instance number */
255 int port_num; /* port instance number */
256
257 /* array of pointers to port contexts on this adapter */
258 struct slgt_info *port_array[SLGT_MAX_PORTS];
259
260 int line; /* tty line instance number */
261
262 struct mgsl_icount icount;
263
264 int timeout;
265 int x_char; /* xon/xoff character */
266 unsigned int read_status_mask;
267 unsigned int ignore_status_mask;
268
269 wait_queue_head_t status_event_wait_q;
270 wait_queue_head_t event_wait_q;
271 struct timer_list tx_timer;
272 struct timer_list rx_timer;
273
274 unsigned int gpio_present;
275 struct cond_wait *gpio_wait_q;
276
277 spinlock_t lock; /* spinlock for synchronizing with ISR */
278
279 struct work_struct task;
280 u32 pending_bh;
281 bool bh_requested;
282 bool bh_running;
283
284 int isr_overflow;
285 bool irq_requested; /* true if IRQ requested */
286 bool irq_occurred; /* for diagnostics use */
287
288 /* device configuration */
289
290 unsigned int bus_type;
291 unsigned int irq_level;
292 unsigned long irq_flags;
293
294 unsigned char __iomem * reg_addr; /* memory mapped registers address */
295 u32 phys_reg_addr;
296 bool reg_addr_requested;
297
298 MGSL_PARAMS params; /* communications parameters */
299 u32 idle_mode;
300 u32 max_frame_size; /* as set by device config */
301
302 unsigned int rbuf_fill_level;
303 unsigned int if_mode;
304
305 /* device status */
306
307 bool rx_enabled;
308 bool rx_restart;
309
310 bool tx_enabled;
311 bool tx_active;
312
313 unsigned char signals; /* serial signal states */
314 int init_error; /* initialization error */
315
316 unsigned char *tx_buf;
317 int tx_count;
318
319 char flag_buf[MAX_ASYNC_BUFFER_SIZE];
320 char char_buf[MAX_ASYNC_BUFFER_SIZE];
321 bool drop_rts_on_tx_done;
322 struct _input_signal_events input_signal_events;
323
324 int dcd_chkcount; /* check counts to prevent */
325 int cts_chkcount; /* too many IRQs if a signal */
326 int dsr_chkcount; /* is floating */
327 int ri_chkcount;
328
329 char *bufs; /* virtual address of DMA buffer lists */
330 dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
331
332 unsigned int rbuf_count;
333 struct slgt_desc *rbufs;
334 unsigned int rbuf_current;
335 unsigned int rbuf_index;
336
337 unsigned int tbuf_count;
338 struct slgt_desc *tbufs;
339 unsigned int tbuf_current;
340 unsigned int tbuf_start;
341
342 unsigned char *tmp_rbuf;
343 unsigned int tmp_rbuf_count;
344
345 /* SPPP/Cisco HDLC device parts */
346
347 int netcount;
348 spinlock_t netlock;
349 #if SYNCLINK_GENERIC_HDLC
350 struct net_device *netdev;
351 #endif
352
353 };
354
355 static MGSL_PARAMS default_params = {
356 .mode = MGSL_MODE_HDLC,
357 .loopback = 0,
358 .flags = HDLC_FLAG_UNDERRUN_ABORT15,
359 .encoding = HDLC_ENCODING_NRZI_SPACE,
360 .clock_speed = 0,
361 .addr_filter = 0xff,
362 .crc_type = HDLC_CRC_16_CCITT,
363 .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
364 .preamble = HDLC_PREAMBLE_PATTERN_NONE,
365 .data_rate = 9600,
366 .data_bits = 8,
367 .stop_bits = 1,
368 .parity = ASYNC_PARITY_NONE
369 };
370
371
372 #define BH_RECEIVE 1
373 #define BH_TRANSMIT 2
374 #define BH_STATUS 4
375 #define IO_PIN_SHUTDOWN_LIMIT 100
376
377 #define DMABUFSIZE 256
378 #define DESC_LIST_SIZE 4096
379
380 #define MASK_PARITY BIT1
381 #define MASK_FRAMING BIT0
382 #define MASK_BREAK BIT14
383 #define MASK_OVERRUN BIT4
384
385 #define GSR 0x00 /* global status */
386 #define JCR 0x04 /* JTAG control */
387 #define IODR 0x08 /* GPIO direction */
388 #define IOER 0x0c /* GPIO interrupt enable */
389 #define IOVR 0x10 /* GPIO value */
390 #define IOSR 0x14 /* GPIO interrupt status */
391 #define TDR 0x80 /* tx data */
392 #define RDR 0x80 /* rx data */
393 #define TCR 0x82 /* tx control */
394 #define TIR 0x84 /* tx idle */
395 #define TPR 0x85 /* tx preamble */
396 #define RCR 0x86 /* rx control */
397 #define VCR 0x88 /* V.24 control */
398 #define CCR 0x89 /* clock control */
399 #define BDR 0x8a /* baud divisor */
400 #define SCR 0x8c /* serial control */
401 #define SSR 0x8e /* serial status */
402 #define RDCSR 0x90 /* rx DMA control/status */
403 #define TDCSR 0x94 /* tx DMA control/status */
404 #define RDDAR 0x98 /* rx DMA descriptor address */
405 #define TDDAR 0x9c /* tx DMA descriptor address */
406
407 #define RXIDLE BIT14
408 #define RXBREAK BIT14
409 #define IRQ_TXDATA BIT13
410 #define IRQ_TXIDLE BIT12
411 #define IRQ_TXUNDER BIT11 /* HDLC */
412 #define IRQ_RXDATA BIT10
413 #define IRQ_RXIDLE BIT9 /* HDLC */
414 #define IRQ_RXBREAK BIT9 /* async */
415 #define IRQ_RXOVER BIT8
416 #define IRQ_DSR BIT7
417 #define IRQ_CTS BIT6
418 #define IRQ_DCD BIT5
419 #define IRQ_RI BIT4
420 #define IRQ_ALL 0x3ff0
421 #define IRQ_MASTER BIT0
422
423 #define slgt_irq_on(info, mask) \
424 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
425 #define slgt_irq_off(info, mask) \
426 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
427
428 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr);
429 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
430 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
431 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
432 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
433 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
434
435 static void msc_set_vcr(struct slgt_info *info);
436
437 static int startup(struct slgt_info *info);
438 static int block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
439 static void shutdown(struct slgt_info *info);
440 static void program_hw(struct slgt_info *info);
441 static void change_params(struct slgt_info *info);
442
443 static int register_test(struct slgt_info *info);
444 static int irq_test(struct slgt_info *info);
445 static int loopback_test(struct slgt_info *info);
446 static int adapter_test(struct slgt_info *info);
447
448 static void reset_adapter(struct slgt_info *info);
449 static void reset_port(struct slgt_info *info);
450 static void async_mode(struct slgt_info *info);
451 static void sync_mode(struct slgt_info *info);
452
453 static void rx_stop(struct slgt_info *info);
454 static void rx_start(struct slgt_info *info);
455 static void reset_rbufs(struct slgt_info *info);
456 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
457 static void rdma_reset(struct slgt_info *info);
458 static bool rx_get_frame(struct slgt_info *info);
459 static bool rx_get_buf(struct slgt_info *info);
460
461 static void tx_start(struct slgt_info *info);
462 static void tx_stop(struct slgt_info *info);
463 static void tx_set_idle(struct slgt_info *info);
464 static unsigned int free_tbuf_count(struct slgt_info *info);
465 static unsigned int tbuf_bytes(struct slgt_info *info);
466 static void reset_tbufs(struct slgt_info *info);
467 static void tdma_reset(struct slgt_info *info);
468 static void tdma_start(struct slgt_info *info);
469 static void tx_load(struct slgt_info *info, const char *buf, unsigned int count);
470
471 static void get_signals(struct slgt_info *info);
472 static void set_signals(struct slgt_info *info);
473 static void enable_loopback(struct slgt_info *info);
474 static void set_rate(struct slgt_info *info, u32 data_rate);
475
476 static int bh_action(struct slgt_info *info);
477 static void bh_handler(struct work_struct *work);
478 static void bh_transmit(struct slgt_info *info);
479 static void isr_serial(struct slgt_info *info);
480 static void isr_rdma(struct slgt_info *info);
481 static void isr_txeom(struct slgt_info *info, unsigned short status);
482 static void isr_tdma(struct slgt_info *info);
483
484 static int alloc_dma_bufs(struct slgt_info *info);
485 static void free_dma_bufs(struct slgt_info *info);
486 static int alloc_desc(struct slgt_info *info);
487 static void free_desc(struct slgt_info *info);
488 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
489 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
490
491 static int alloc_tmp_rbuf(struct slgt_info *info);
492 static void free_tmp_rbuf(struct slgt_info *info);
493
494 static void tx_timeout(unsigned long context);
495 static void rx_timeout(unsigned long context);
496
497 /*
498 * ioctl handlers
499 */
500 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
501 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
502 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
503 static int get_txidle(struct slgt_info *info, int __user *idle_mode);
504 static int set_txidle(struct slgt_info *info, int idle_mode);
505 static int tx_enable(struct slgt_info *info, int enable);
506 static int tx_abort(struct slgt_info *info);
507 static int rx_enable(struct slgt_info *info, int enable);
508 static int modem_input_wait(struct slgt_info *info,int arg);
509 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
510 static int tiocmget(struct tty_struct *tty, struct file *file);
511 static int tiocmset(struct tty_struct *tty, struct file *file,
512 unsigned int set, unsigned int clear);
513 static int set_break(struct tty_struct *tty, int break_state);
514 static int get_interface(struct slgt_info *info, int __user *if_mode);
515 static int set_interface(struct slgt_info *info, int if_mode);
516 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
517 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
518 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
519
520 /*
521 * driver functions
522 */
523 static void add_device(struct slgt_info *info);
524 static void device_init(int adapter_num, struct pci_dev *pdev);
525 static int claim_resources(struct slgt_info *info);
526 static void release_resources(struct slgt_info *info);
527
528 /*
529 * DEBUG OUTPUT CODE
530 */
531 #ifndef DBGINFO
532 #define DBGINFO(fmt)
533 #endif
534 #ifndef DBGERR
535 #define DBGERR(fmt)
536 #endif
537 #ifndef DBGBH
538 #define DBGBH(fmt)
539 #endif
540 #ifndef DBGISR
541 #define DBGISR(fmt)
542 #endif
543
544 #ifdef DBGDATA
545 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
546 {
547 int i;
548 int linecount;
549 printk("%s %s data:\n",info->device_name, label);
550 while(count) {
551 linecount = (count > 16) ? 16 : count;
552 for(i=0; i < linecount; i++)
553 printk("%02X ",(unsigned char)data[i]);
554 for(;i<17;i++)
555 printk(" ");
556 for(i=0;i<linecount;i++) {
557 if (data[i]>=040 && data[i]<=0176)
558 printk("%c",data[i]);
559 else
560 printk(".");
561 }
562 printk("\n");
563 data += linecount;
564 count -= linecount;
565 }
566 }
567 #else
568 #define DBGDATA(info, buf, size, label)
569 #endif
570
571 #ifdef DBGTBUF
572 static void dump_tbufs(struct slgt_info *info)
573 {
574 int i;
575 printk("tbuf_current=%d\n", info->tbuf_current);
576 for (i=0 ; i < info->tbuf_count ; i++) {
577 printk("%d: count=%04X status=%04X\n",
578 i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
579 }
580 }
581 #else
582 #define DBGTBUF(info)
583 #endif
584
585 #ifdef DBGRBUF
586 static void dump_rbufs(struct slgt_info *info)
587 {
588 int i;
589 printk("rbuf_current=%d\n", info->rbuf_current);
590 for (i=0 ; i < info->rbuf_count ; i++) {
591 printk("%d: count=%04X status=%04X\n",
592 i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
593 }
594 }
595 #else
596 #define DBGRBUF(info)
597 #endif
598
599 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
600 {
601 #ifdef SANITY_CHECK
602 if (!info) {
603 printk("null struct slgt_info for (%s) in %s\n", devname, name);
604 return 1;
605 }
606 if (info->magic != MGSL_MAGIC) {
607 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
608 return 1;
609 }
610 #else
611 if (!info)
612 return 1;
613 #endif
614 return 0;
615 }
616
617 /**
618 * line discipline callback wrappers
619 *
620 * The wrappers maintain line discipline references
621 * while calling into the line discipline.
622 *
623 * ldisc_receive_buf - pass receive data to line discipline
624 */
625 static void ldisc_receive_buf(struct tty_struct *tty,
626 const __u8 *data, char *flags, int count)
627 {
628 struct tty_ldisc *ld;
629 if (!tty)
630 return;
631 ld = tty_ldisc_ref(tty);
632 if (ld) {
633 if (ld->ops->receive_buf)
634 ld->ops->receive_buf(tty, data, flags, count);
635 tty_ldisc_deref(ld);
636 }
637 }
638
639 /* tty callbacks */
640
641 static int open(struct tty_struct *tty, struct file *filp)
642 {
643 struct slgt_info *info;
644 int retval, line;
645 unsigned long flags;
646
647 line = tty->index;
648 if ((line < 0) || (line >= slgt_device_count)) {
649 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
650 return -ENODEV;
651 }
652
653 info = slgt_device_list;
654 while(info && info->line != line)
655 info = info->next_device;
656 if (sanity_check(info, tty->name, "open"))
657 return -ENODEV;
658 if (info->init_error) {
659 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
660 return -ENODEV;
661 }
662
663 tty->driver_data = info;
664 info->port.tty = tty;
665
666 DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
667
668 /* If port is closing, signal caller to try again */
669 if (tty_hung_up_p(filp) || info->port.flags & ASYNC_CLOSING){
670 if (info->port.flags & ASYNC_CLOSING)
671 interruptible_sleep_on(&info->port.close_wait);
672 retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
673 -EAGAIN : -ERESTARTSYS);
674 goto cleanup;
675 }
676
677 info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
678
679 spin_lock_irqsave(&info->netlock, flags);
680 if (info->netcount) {
681 retval = -EBUSY;
682 spin_unlock_irqrestore(&info->netlock, flags);
683 goto cleanup;
684 }
685 info->port.count++;
686 spin_unlock_irqrestore(&info->netlock, flags);
687
688 if (info->port.count == 1) {
689 /* 1st open on this device, init hardware */
690 retval = startup(info);
691 if (retval < 0)
692 goto cleanup;
693 }
694
695 retval = block_til_ready(tty, filp, info);
696 if (retval) {
697 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
698 goto cleanup;
699 }
700
701 retval = 0;
702
703 cleanup:
704 if (retval) {
705 if (tty->count == 1)
706 info->port.tty = NULL; /* tty layer will release tty struct */
707 if(info->port.count)
708 info->port.count--;
709 }
710
711 DBGINFO(("%s open rc=%d\n", info->device_name, retval));
712 return retval;
713 }
714
715 static void close(struct tty_struct *tty, struct file *filp)
716 {
717 struct slgt_info *info = tty->driver_data;
718
719 if (sanity_check(info, tty->name, "close"))
720 return;
721 DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
722
723 if (!info->port.count)
724 return;
725
726 if (tty_hung_up_p(filp))
727 goto cleanup;
728
729 if ((tty->count == 1) && (info->port.count != 1)) {
730 /*
731 * tty->count is 1 and the tty structure will be freed.
732 * info->port.count should be one in this case.
733 * if it's not, correct it so that the port is shutdown.
734 */
735 DBGERR(("%s close: bad refcount; tty->count=1, "
736 "info->port.count=%d\n", info->device_name, info->port.count));
737 info->port.count = 1;
738 }
739
740 info->port.count--;
741
742 /* if at least one open remaining, leave hardware active */
743 if (info->port.count)
744 goto cleanup;
745
746 info->port.flags |= ASYNC_CLOSING;
747
748 /* set tty->closing to notify line discipline to
749 * only process XON/XOFF characters. Only the N_TTY
750 * discipline appears to use this (ppp does not).
751 */
752 tty->closing = 1;
753
754 /* wait for transmit data to clear all layers */
755
756 if (info->port.closing_wait != ASYNC_CLOSING_WAIT_NONE) {
757 DBGINFO(("%s call tty_wait_until_sent\n", info->device_name));
758 tty_wait_until_sent(tty, info->port.closing_wait);
759 }
760
761 if (info->port.flags & ASYNC_INITIALIZED)
762 wait_until_sent(tty, info->timeout);
763 flush_buffer(tty);
764 tty_ldisc_flush(tty);
765
766 shutdown(info);
767
768 tty->closing = 0;
769 info->port.tty = NULL;
770
771 if (info->port.blocked_open) {
772 if (info->port.close_delay) {
773 msleep_interruptible(jiffies_to_msecs(info->port.close_delay));
774 }
775 wake_up_interruptible(&info->port.open_wait);
776 }
777
778 info->port.flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
779
780 wake_up_interruptible(&info->port.close_wait);
781
782 cleanup:
783 DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
784 }
785
786 static void hangup(struct tty_struct *tty)
787 {
788 struct slgt_info *info = tty->driver_data;
789
790 if (sanity_check(info, tty->name, "hangup"))
791 return;
792 DBGINFO(("%s hangup\n", info->device_name));
793
794 flush_buffer(tty);
795 shutdown(info);
796
797 info->port.count = 0;
798 info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
799 info->port.tty = NULL;
800
801 wake_up_interruptible(&info->port.open_wait);
802 }
803
804 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
805 {
806 struct slgt_info *info = tty->driver_data;
807 unsigned long flags;
808
809 DBGINFO(("%s set_termios\n", tty->driver->name));
810
811 change_params(info);
812
813 /* Handle transition to B0 status */
814 if (old_termios->c_cflag & CBAUD &&
815 !(tty->termios->c_cflag & CBAUD)) {
816 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
817 spin_lock_irqsave(&info->lock,flags);
818 set_signals(info);
819 spin_unlock_irqrestore(&info->lock,flags);
820 }
821
822 /* Handle transition away from B0 status */
823 if (!(old_termios->c_cflag & CBAUD) &&
824 tty->termios->c_cflag & CBAUD) {
825 info->signals |= SerialSignal_DTR;
826 if (!(tty->termios->c_cflag & CRTSCTS) ||
827 !test_bit(TTY_THROTTLED, &tty->flags)) {
828 info->signals |= SerialSignal_RTS;
829 }
830 spin_lock_irqsave(&info->lock,flags);
831 set_signals(info);
832 spin_unlock_irqrestore(&info->lock,flags);
833 }
834
835 /* Handle turning off CRTSCTS */
836 if (old_termios->c_cflag & CRTSCTS &&
837 !(tty->termios->c_cflag & CRTSCTS)) {
838 tty->hw_stopped = 0;
839 tx_release(tty);
840 }
841 }
842
843 static int write(struct tty_struct *tty,
844 const unsigned char *buf, int count)
845 {
846 int ret = 0;
847 struct slgt_info *info = tty->driver_data;
848 unsigned long flags;
849 unsigned int bufs_needed;
850
851 if (sanity_check(info, tty->name, "write"))
852 goto cleanup;
853 DBGINFO(("%s write count=%d\n", info->device_name, count));
854
855 if (!info->tx_buf)
856 goto cleanup;
857
858 if (count > info->max_frame_size) {
859 ret = -EIO;
860 goto cleanup;
861 }
862
863 if (!count)
864 goto cleanup;
865
866 if (!info->tx_active && info->tx_count) {
867 /* send accumulated data from send_char() */
868 tx_load(info, info->tx_buf, info->tx_count);
869 goto start;
870 }
871 bufs_needed = (count/DMABUFSIZE);
872 if (count % DMABUFSIZE)
873 ++bufs_needed;
874 if (bufs_needed > free_tbuf_count(info))
875 goto cleanup;
876
877 ret = info->tx_count = count;
878 tx_load(info, buf, count);
879 goto start;
880
881 start:
882 if (info->tx_count && !tty->stopped && !tty->hw_stopped) {
883 spin_lock_irqsave(&info->lock,flags);
884 if (!info->tx_active)
885 tx_start(info);
886 else
887 tdma_start(info);
888 spin_unlock_irqrestore(&info->lock,flags);
889 }
890
891 cleanup:
892 DBGINFO(("%s write rc=%d\n", info->device_name, ret));
893 return ret;
894 }
895
896 static int put_char(struct tty_struct *tty, unsigned char ch)
897 {
898 struct slgt_info *info = tty->driver_data;
899 unsigned long flags;
900 int ret = 0;
901
902 if (sanity_check(info, tty->name, "put_char"))
903 return 0;
904 DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
905 if (!info->tx_buf)
906 return 0;
907 spin_lock_irqsave(&info->lock,flags);
908 if (!info->tx_active && (info->tx_count < info->max_frame_size)) {
909 info->tx_buf[info->tx_count++] = ch;
910 ret = 1;
911 }
912 spin_unlock_irqrestore(&info->lock,flags);
913 return ret;
914 }
915
916 static void send_xchar(struct tty_struct *tty, char ch)
917 {
918 struct slgt_info *info = tty->driver_data;
919 unsigned long flags;
920
921 if (sanity_check(info, tty->name, "send_xchar"))
922 return;
923 DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
924 info->x_char = ch;
925 if (ch) {
926 spin_lock_irqsave(&info->lock,flags);
927 if (!info->tx_enabled)
928 tx_start(info);
929 spin_unlock_irqrestore(&info->lock,flags);
930 }
931 }
932
933 static void wait_until_sent(struct tty_struct *tty, int timeout)
934 {
935 struct slgt_info *info = tty->driver_data;
936 unsigned long orig_jiffies, char_time;
937
938 if (!info )
939 return;
940 if (sanity_check(info, tty->name, "wait_until_sent"))
941 return;
942 DBGINFO(("%s wait_until_sent entry\n", info->device_name));
943 if (!(info->port.flags & ASYNC_INITIALIZED))
944 goto exit;
945
946 orig_jiffies = jiffies;
947
948 /* Set check interval to 1/5 of estimated time to
949 * send a character, and make it at least 1. The check
950 * interval should also be less than the timeout.
951 * Note: use tight timings here to satisfy the NIST-PCTS.
952 */
953
954 lock_kernel();
955
956 if (info->params.data_rate) {
957 char_time = info->timeout/(32 * 5);
958 if (!char_time)
959 char_time++;
960 } else
961 char_time = 1;
962
963 if (timeout)
964 char_time = min_t(unsigned long, char_time, timeout);
965
966 while (info->tx_active) {
967 msleep_interruptible(jiffies_to_msecs(char_time));
968 if (signal_pending(current))
969 break;
970 if (timeout && time_after(jiffies, orig_jiffies + timeout))
971 break;
972 }
973 unlock_kernel();
974
975 exit:
976 DBGINFO(("%s wait_until_sent exit\n", info->device_name));
977 }
978
979 static int write_room(struct tty_struct *tty)
980 {
981 struct slgt_info *info = tty->driver_data;
982 int ret;
983
984 if (sanity_check(info, tty->name, "write_room"))
985 return 0;
986 ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
987 DBGINFO(("%s write_room=%d\n", info->device_name, ret));
988 return ret;
989 }
990
991 static void flush_chars(struct tty_struct *tty)
992 {
993 struct slgt_info *info = tty->driver_data;
994 unsigned long flags;
995
996 if (sanity_check(info, tty->name, "flush_chars"))
997 return;
998 DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
999
1000 if (info->tx_count <= 0 || tty->stopped ||
1001 tty->hw_stopped || !info->tx_buf)
1002 return;
1003
1004 DBGINFO(("%s flush_chars start transmit\n", info->device_name));
1005
1006 spin_lock_irqsave(&info->lock,flags);
1007 if (!info->tx_active && info->tx_count) {
1008 tx_load(info, info->tx_buf,info->tx_count);
1009 tx_start(info);
1010 }
1011 spin_unlock_irqrestore(&info->lock,flags);
1012 }
1013
1014 static void flush_buffer(struct tty_struct *tty)
1015 {
1016 struct slgt_info *info = tty->driver_data;
1017 unsigned long flags;
1018
1019 if (sanity_check(info, tty->name, "flush_buffer"))
1020 return;
1021 DBGINFO(("%s flush_buffer\n", info->device_name));
1022
1023 spin_lock_irqsave(&info->lock,flags);
1024 if (!info->tx_active)
1025 info->tx_count = 0;
1026 spin_unlock_irqrestore(&info->lock,flags);
1027
1028 tty_wakeup(tty);
1029 }
1030
1031 /*
1032 * throttle (stop) transmitter
1033 */
1034 static void tx_hold(struct tty_struct *tty)
1035 {
1036 struct slgt_info *info = tty->driver_data;
1037 unsigned long flags;
1038
1039 if (sanity_check(info, tty->name, "tx_hold"))
1040 return;
1041 DBGINFO(("%s tx_hold\n", info->device_name));
1042 spin_lock_irqsave(&info->lock,flags);
1043 if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1044 tx_stop(info);
1045 spin_unlock_irqrestore(&info->lock,flags);
1046 }
1047
1048 /*
1049 * release (start) transmitter
1050 */
1051 static void tx_release(struct tty_struct *tty)
1052 {
1053 struct slgt_info *info = tty->driver_data;
1054 unsigned long flags;
1055
1056 if (sanity_check(info, tty->name, "tx_release"))
1057 return;
1058 DBGINFO(("%s tx_release\n", info->device_name));
1059 spin_lock_irqsave(&info->lock,flags);
1060 if (!info->tx_active && info->tx_count) {
1061 tx_load(info, info->tx_buf, info->tx_count);
1062 tx_start(info);
1063 }
1064 spin_unlock_irqrestore(&info->lock,flags);
1065 }
1066
1067 /*
1068 * Service an IOCTL request
1069 *
1070 * Arguments
1071 *
1072 * tty pointer to tty instance data
1073 * file pointer to associated file object for device
1074 * cmd IOCTL command code
1075 * arg command argument/context
1076 *
1077 * Return 0 if success, otherwise error code
1078 */
1079 static int ioctl(struct tty_struct *tty, struct file *file,
1080 unsigned int cmd, unsigned long arg)
1081 {
1082 struct slgt_info *info = tty->driver_data;
1083 struct mgsl_icount cnow; /* kernel counter temps */
1084 struct serial_icounter_struct __user *p_cuser; /* user space */
1085 unsigned long flags;
1086 void __user *argp = (void __user *)arg;
1087 int ret;
1088
1089 if (sanity_check(info, tty->name, "ioctl"))
1090 return -ENODEV;
1091 DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1092
1093 if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1094 (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
1095 if (tty->flags & (1 << TTY_IO_ERROR))
1096 return -EIO;
1097 }
1098
1099 lock_kernel();
1100
1101 switch (cmd) {
1102 case MGSL_IOCGPARAMS:
1103 ret = get_params(info, argp);
1104 break;
1105 case MGSL_IOCSPARAMS:
1106 ret = set_params(info, argp);
1107 break;
1108 case MGSL_IOCGTXIDLE:
1109 ret = get_txidle(info, argp);
1110 break;
1111 case MGSL_IOCSTXIDLE:
1112 ret = set_txidle(info, (int)arg);
1113 break;
1114 case MGSL_IOCTXENABLE:
1115 ret = tx_enable(info, (int)arg);
1116 break;
1117 case MGSL_IOCRXENABLE:
1118 ret = rx_enable(info, (int)arg);
1119 break;
1120 case MGSL_IOCTXABORT:
1121 ret = tx_abort(info);
1122 break;
1123 case MGSL_IOCGSTATS:
1124 ret = get_stats(info, argp);
1125 break;
1126 case MGSL_IOCWAITEVENT:
1127 ret = wait_mgsl_event(info, argp);
1128 break;
1129 case TIOCMIWAIT:
1130 ret = modem_input_wait(info,(int)arg);
1131 break;
1132 case MGSL_IOCGIF:
1133 ret = get_interface(info, argp);
1134 break;
1135 case MGSL_IOCSIF:
1136 ret = set_interface(info,(int)arg);
1137 break;
1138 case MGSL_IOCSGPIO:
1139 ret = set_gpio(info, argp);
1140 break;
1141 case MGSL_IOCGGPIO:
1142 ret = get_gpio(info, argp);
1143 break;
1144 case MGSL_IOCWAITGPIO:
1145 ret = wait_gpio(info, argp);
1146 break;
1147 case TIOCGICOUNT:
1148 spin_lock_irqsave(&info->lock,flags);
1149 cnow = info->icount;
1150 spin_unlock_irqrestore(&info->lock,flags);
1151 p_cuser = argp;
1152 if (put_user(cnow.cts, &p_cuser->cts) ||
1153 put_user(cnow.dsr, &p_cuser->dsr) ||
1154 put_user(cnow.rng, &p_cuser->rng) ||
1155 put_user(cnow.dcd, &p_cuser->dcd) ||
1156 put_user(cnow.rx, &p_cuser->rx) ||
1157 put_user(cnow.tx, &p_cuser->tx) ||
1158 put_user(cnow.frame, &p_cuser->frame) ||
1159 put_user(cnow.overrun, &p_cuser->overrun) ||
1160 put_user(cnow.parity, &p_cuser->parity) ||
1161 put_user(cnow.brk, &p_cuser->brk) ||
1162 put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
1163 ret = -EFAULT;
1164 ret = 0;
1165 break;
1166 default:
1167 ret = -ENOIOCTLCMD;
1168 }
1169 unlock_kernel();
1170 return ret;
1171 }
1172
1173 /*
1174 * support for 32 bit ioctl calls on 64 bit systems
1175 */
1176 #ifdef CONFIG_COMPAT
1177 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1178 {
1179 struct MGSL_PARAMS32 tmp_params;
1180
1181 DBGINFO(("%s get_params32\n", info->device_name));
1182 tmp_params.mode = (compat_ulong_t)info->params.mode;
1183 tmp_params.loopback = info->params.loopback;
1184 tmp_params.flags = info->params.flags;
1185 tmp_params.encoding = info->params.encoding;
1186 tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed;
1187 tmp_params.addr_filter = info->params.addr_filter;
1188 tmp_params.crc_type = info->params.crc_type;
1189 tmp_params.preamble_length = info->params.preamble_length;
1190 tmp_params.preamble = info->params.preamble;
1191 tmp_params.data_rate = (compat_ulong_t)info->params.data_rate;
1192 tmp_params.data_bits = info->params.data_bits;
1193 tmp_params.stop_bits = info->params.stop_bits;
1194 tmp_params.parity = info->params.parity;
1195 if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1196 return -EFAULT;
1197 return 0;
1198 }
1199
1200 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1201 {
1202 struct MGSL_PARAMS32 tmp_params;
1203
1204 DBGINFO(("%s set_params32\n", info->device_name));
1205 if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1206 return -EFAULT;
1207
1208 spin_lock(&info->lock);
1209 info->params.mode = tmp_params.mode;
1210 info->params.loopback = tmp_params.loopback;
1211 info->params.flags = tmp_params.flags;
1212 info->params.encoding = tmp_params.encoding;
1213 info->params.clock_speed = tmp_params.clock_speed;
1214 info->params.addr_filter = tmp_params.addr_filter;
1215 info->params.crc_type = tmp_params.crc_type;
1216 info->params.preamble_length = tmp_params.preamble_length;
1217 info->params.preamble = tmp_params.preamble;
1218 info->params.data_rate = tmp_params.data_rate;
1219 info->params.data_bits = tmp_params.data_bits;
1220 info->params.stop_bits = tmp_params.stop_bits;
1221 info->params.parity = tmp_params.parity;
1222 spin_unlock(&info->lock);
1223
1224 change_params(info);
1225
1226 return 0;
1227 }
1228
1229 static long slgt_compat_ioctl(struct tty_struct *tty, struct file *file,
1230 unsigned int cmd, unsigned long arg)
1231 {
1232 struct slgt_info *info = tty->driver_data;
1233 int rc = -ENOIOCTLCMD;
1234
1235 if (sanity_check(info, tty->name, "compat_ioctl"))
1236 return -ENODEV;
1237 DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1238
1239 switch (cmd) {
1240
1241 case MGSL_IOCSPARAMS32:
1242 rc = set_params32(info, compat_ptr(arg));
1243 break;
1244
1245 case MGSL_IOCGPARAMS32:
1246 rc = get_params32(info, compat_ptr(arg));
1247 break;
1248
1249 case MGSL_IOCGPARAMS:
1250 case MGSL_IOCSPARAMS:
1251 case MGSL_IOCGTXIDLE:
1252 case MGSL_IOCGSTATS:
1253 case MGSL_IOCWAITEVENT:
1254 case MGSL_IOCGIF:
1255 case MGSL_IOCSGPIO:
1256 case MGSL_IOCGGPIO:
1257 case MGSL_IOCWAITGPIO:
1258 case TIOCGICOUNT:
1259 rc = ioctl(tty, file, cmd, (unsigned long)(compat_ptr(arg)));
1260 break;
1261
1262 case MGSL_IOCSTXIDLE:
1263 case MGSL_IOCTXENABLE:
1264 case MGSL_IOCRXENABLE:
1265 case MGSL_IOCTXABORT:
1266 case TIOCMIWAIT:
1267 case MGSL_IOCSIF:
1268 rc = ioctl(tty, file, cmd, arg);
1269 break;
1270 }
1271
1272 DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1273 return rc;
1274 }
1275 #else
1276 #define slgt_compat_ioctl NULL
1277 #endif /* ifdef CONFIG_COMPAT */
1278
1279 /*
1280 * proc fs support
1281 */
1282 static inline int line_info(char *buf, struct slgt_info *info)
1283 {
1284 char stat_buf[30];
1285 int ret;
1286 unsigned long flags;
1287
1288 ret = sprintf(buf, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1289 info->device_name, info->phys_reg_addr,
1290 info->irq_level, info->max_frame_size);
1291
1292 /* output current serial signal states */
1293 spin_lock_irqsave(&info->lock,flags);
1294 get_signals(info);
1295 spin_unlock_irqrestore(&info->lock,flags);
1296
1297 stat_buf[0] = 0;
1298 stat_buf[1] = 0;
1299 if (info->signals & SerialSignal_RTS)
1300 strcat(stat_buf, "|RTS");
1301 if (info->signals & SerialSignal_CTS)
1302 strcat(stat_buf, "|CTS");
1303 if (info->signals & SerialSignal_DTR)
1304 strcat(stat_buf, "|DTR");
1305 if (info->signals & SerialSignal_DSR)
1306 strcat(stat_buf, "|DSR");
1307 if (info->signals & SerialSignal_DCD)
1308 strcat(stat_buf, "|CD");
1309 if (info->signals & SerialSignal_RI)
1310 strcat(stat_buf, "|RI");
1311
1312 if (info->params.mode != MGSL_MODE_ASYNC) {
1313 ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
1314 info->icount.txok, info->icount.rxok);
1315 if (info->icount.txunder)
1316 ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
1317 if (info->icount.txabort)
1318 ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
1319 if (info->icount.rxshort)
1320 ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
1321 if (info->icount.rxlong)
1322 ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
1323 if (info->icount.rxover)
1324 ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
1325 if (info->icount.rxcrc)
1326 ret += sprintf(buf+ret, " rxcrc:%d", info->icount.rxcrc);
1327 } else {
1328 ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
1329 info->icount.tx, info->icount.rx);
1330 if (info->icount.frame)
1331 ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
1332 if (info->icount.parity)
1333 ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
1334 if (info->icount.brk)
1335 ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
1336 if (info->icount.overrun)
1337 ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
1338 }
1339
1340 /* Append serial signal status to end */
1341 ret += sprintf(buf+ret, " %s\n", stat_buf+1);
1342
1343 ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1344 info->tx_active,info->bh_requested,info->bh_running,
1345 info->pending_bh);
1346
1347 return ret;
1348 }
1349
1350 /* Called to print information about devices
1351 */
1352 static int read_proc(char *page, char **start, off_t off, int count,
1353 int *eof, void *data)
1354 {
1355 int len = 0, l;
1356 off_t begin = 0;
1357 struct slgt_info *info;
1358
1359 len += sprintf(page, "synclink_gt driver:%s\n", driver_version);
1360
1361 info = slgt_device_list;
1362 while( info ) {
1363 l = line_info(page + len, info);
1364 len += l;
1365 if (len+begin > off+count)
1366 goto done;
1367 if (len+begin < off) {
1368 begin += len;
1369 len = 0;
1370 }
1371 info = info->next_device;
1372 }
1373
1374 *eof = 1;
1375 done:
1376 if (off >= len+begin)
1377 return 0;
1378 *start = page + (off-begin);
1379 return ((count < begin+len-off) ? count : begin+len-off);
1380 }
1381
1382 /*
1383 * return count of bytes in transmit buffer
1384 */
1385 static int chars_in_buffer(struct tty_struct *tty)
1386 {
1387 struct slgt_info *info = tty->driver_data;
1388 int count;
1389 if (sanity_check(info, tty->name, "chars_in_buffer"))
1390 return 0;
1391 count = tbuf_bytes(info);
1392 DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1393 return count;
1394 }
1395
1396 /*
1397 * signal remote device to throttle send data (our receive data)
1398 */
1399 static void throttle(struct tty_struct * tty)
1400 {
1401 struct slgt_info *info = tty->driver_data;
1402 unsigned long flags;
1403
1404 if (sanity_check(info, tty->name, "throttle"))
1405 return;
1406 DBGINFO(("%s throttle\n", info->device_name));
1407 if (I_IXOFF(tty))
1408 send_xchar(tty, STOP_CHAR(tty));
1409 if (tty->termios->c_cflag & CRTSCTS) {
1410 spin_lock_irqsave(&info->lock,flags);
1411 info->signals &= ~SerialSignal_RTS;
1412 set_signals(info);
1413 spin_unlock_irqrestore(&info->lock,flags);
1414 }
1415 }
1416
1417 /*
1418 * signal remote device to stop throttling send data (our receive data)
1419 */
1420 static void unthrottle(struct tty_struct * tty)
1421 {
1422 struct slgt_info *info = tty->driver_data;
1423 unsigned long flags;
1424
1425 if (sanity_check(info, tty->name, "unthrottle"))
1426 return;
1427 DBGINFO(("%s unthrottle\n", info->device_name));
1428 if (I_IXOFF(tty)) {
1429 if (info->x_char)
1430 info->x_char = 0;
1431 else
1432 send_xchar(tty, START_CHAR(tty));
1433 }
1434 if (tty->termios->c_cflag & CRTSCTS) {
1435 spin_lock_irqsave(&info->lock,flags);
1436 info->signals |= SerialSignal_RTS;
1437 set_signals(info);
1438 spin_unlock_irqrestore(&info->lock,flags);
1439 }
1440 }
1441
1442 /*
1443 * set or clear transmit break condition
1444 * break_state -1=set break condition, 0=clear
1445 */
1446 static int set_break(struct tty_struct *tty, int break_state)
1447 {
1448 struct slgt_info *info = tty->driver_data;
1449 unsigned short value;
1450 unsigned long flags;
1451
1452 if (sanity_check(info, tty->name, "set_break"))
1453 return -EINVAL;
1454 DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1455
1456 spin_lock_irqsave(&info->lock,flags);
1457 value = rd_reg16(info, TCR);
1458 if (break_state == -1)
1459 value |= BIT6;
1460 else
1461 value &= ~BIT6;
1462 wr_reg16(info, TCR, value);
1463 spin_unlock_irqrestore(&info->lock,flags);
1464 return 0;
1465 }
1466
1467 #if SYNCLINK_GENERIC_HDLC
1468
1469 /**
1470 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1471 * set encoding and frame check sequence (FCS) options
1472 *
1473 * dev pointer to network device structure
1474 * encoding serial encoding setting
1475 * parity FCS setting
1476 *
1477 * returns 0 if success, otherwise error code
1478 */
1479 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1480 unsigned short parity)
1481 {
1482 struct slgt_info *info = dev_to_port(dev);
1483 unsigned char new_encoding;
1484 unsigned short new_crctype;
1485
1486 /* return error if TTY interface open */
1487 if (info->port.count)
1488 return -EBUSY;
1489
1490 DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1491
1492 switch (encoding)
1493 {
1494 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break;
1495 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1496 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1497 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1498 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1499 default: return -EINVAL;
1500 }
1501
1502 switch (parity)
1503 {
1504 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break;
1505 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1506 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1507 default: return -EINVAL;
1508 }
1509
1510 info->params.encoding = new_encoding;
1511 info->params.crc_type = new_crctype;
1512
1513 /* if network interface up, reprogram hardware */
1514 if (info->netcount)
1515 program_hw(info);
1516
1517 return 0;
1518 }
1519
1520 /**
1521 * called by generic HDLC layer to send frame
1522 *
1523 * skb socket buffer containing HDLC frame
1524 * dev pointer to network device structure
1525 *
1526 * returns 0 if success, otherwise error code
1527 */
1528 static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
1529 {
1530 struct slgt_info *info = dev_to_port(dev);
1531 unsigned long flags;
1532
1533 DBGINFO(("%s hdlc_xmit\n", dev->name));
1534
1535 /* stop sending until this frame completes */
1536 netif_stop_queue(dev);
1537
1538 /* copy data to device buffers */
1539 info->tx_count = skb->len;
1540 tx_load(info, skb->data, skb->len);
1541
1542 /* update network statistics */
1543 dev->stats.tx_packets++;
1544 dev->stats.tx_bytes += skb->len;
1545
1546 /* done with socket buffer, so free it */
1547 dev_kfree_skb(skb);
1548
1549 /* save start time for transmit timeout detection */
1550 dev->trans_start = jiffies;
1551
1552 /* start hardware transmitter if necessary */
1553 spin_lock_irqsave(&info->lock,flags);
1554 if (!info->tx_active)
1555 tx_start(info);
1556 spin_unlock_irqrestore(&info->lock,flags);
1557
1558 return 0;
1559 }
1560
1561 /**
1562 * called by network layer when interface enabled
1563 * claim resources and initialize hardware
1564 *
1565 * dev pointer to network device structure
1566 *
1567 * returns 0 if success, otherwise error code
1568 */
1569 static int hdlcdev_open(struct net_device *dev)
1570 {
1571 struct slgt_info *info = dev_to_port(dev);
1572 int rc;
1573 unsigned long flags;
1574
1575 if (!try_module_get(THIS_MODULE))
1576 return -EBUSY;
1577
1578 DBGINFO(("%s hdlcdev_open\n", dev->name));
1579
1580 /* generic HDLC layer open processing */
1581 if ((rc = hdlc_open(dev)))
1582 return rc;
1583
1584 /* arbitrate between network and tty opens */
1585 spin_lock_irqsave(&info->netlock, flags);
1586 if (info->port.count != 0 || info->netcount != 0) {
1587 DBGINFO(("%s hdlc_open busy\n", dev->name));
1588 spin_unlock_irqrestore(&info->netlock, flags);
1589 return -EBUSY;
1590 }
1591 info->netcount=1;
1592 spin_unlock_irqrestore(&info->netlock, flags);
1593
1594 /* claim resources and init adapter */
1595 if ((rc = startup(info)) != 0) {
1596 spin_lock_irqsave(&info->netlock, flags);
1597 info->netcount=0;
1598 spin_unlock_irqrestore(&info->netlock, flags);
1599 return rc;
1600 }
1601
1602 /* assert DTR and RTS, apply hardware settings */
1603 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1604 program_hw(info);
1605
1606 /* enable network layer transmit */
1607 dev->trans_start = jiffies;
1608 netif_start_queue(dev);
1609
1610 /* inform generic HDLC layer of current DCD status */
1611 spin_lock_irqsave(&info->lock, flags);
1612 get_signals(info);
1613 spin_unlock_irqrestore(&info->lock, flags);
1614 if (info->signals & SerialSignal_DCD)
1615 netif_carrier_on(dev);
1616 else
1617 netif_carrier_off(dev);
1618 return 0;
1619 }
1620
1621 /**
1622 * called by network layer when interface is disabled
1623 * shutdown hardware and release resources
1624 *
1625 * dev pointer to network device structure
1626 *
1627 * returns 0 if success, otherwise error code
1628 */
1629 static int hdlcdev_close(struct net_device *dev)
1630 {
1631 struct slgt_info *info = dev_to_port(dev);
1632 unsigned long flags;
1633
1634 DBGINFO(("%s hdlcdev_close\n", dev->name));
1635
1636 netif_stop_queue(dev);
1637
1638 /* shutdown adapter and release resources */
1639 shutdown(info);
1640
1641 hdlc_close(dev);
1642
1643 spin_lock_irqsave(&info->netlock, flags);
1644 info->netcount=0;
1645 spin_unlock_irqrestore(&info->netlock, flags);
1646
1647 module_put(THIS_MODULE);
1648 return 0;
1649 }
1650
1651 /**
1652 * called by network layer to process IOCTL call to network device
1653 *
1654 * dev pointer to network device structure
1655 * ifr pointer to network interface request structure
1656 * cmd IOCTL command code
1657 *
1658 * returns 0 if success, otherwise error code
1659 */
1660 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1661 {
1662 const size_t size = sizeof(sync_serial_settings);
1663 sync_serial_settings new_line;
1664 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1665 struct slgt_info *info = dev_to_port(dev);
1666 unsigned int flags;
1667
1668 DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1669
1670 /* return error if TTY interface open */
1671 if (info->port.count)
1672 return -EBUSY;
1673
1674 if (cmd != SIOCWANDEV)
1675 return hdlc_ioctl(dev, ifr, cmd);
1676
1677 switch(ifr->ifr_settings.type) {
1678 case IF_GET_IFACE: /* return current sync_serial_settings */
1679
1680 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1681 if (ifr->ifr_settings.size < size) {
1682 ifr->ifr_settings.size = size; /* data size wanted */
1683 return -ENOBUFS;
1684 }
1685
1686 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1687 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1688 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1689 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1690
1691 switch (flags){
1692 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1693 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break;
1694 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break;
1695 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1696 default: new_line.clock_type = CLOCK_DEFAULT;
1697 }
1698
1699 new_line.clock_rate = info->params.clock_speed;
1700 new_line.loopback = info->params.loopback ? 1:0;
1701
1702 if (copy_to_user(line, &new_line, size))
1703 return -EFAULT;
1704 return 0;
1705
1706 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1707
1708 if(!capable(CAP_NET_ADMIN))
1709 return -EPERM;
1710 if (copy_from_user(&new_line, line, size))
1711 return -EFAULT;
1712
1713 switch (new_line.clock_type)
1714 {
1715 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1716 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1717 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break;
1718 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break;
1719 case CLOCK_DEFAULT: flags = info->params.flags &
1720 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1721 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1722 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1723 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break;
1724 default: return -EINVAL;
1725 }
1726
1727 if (new_line.loopback != 0 && new_line.loopback != 1)
1728 return -EINVAL;
1729
1730 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1731 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1732 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1733 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1734 info->params.flags |= flags;
1735
1736 info->params.loopback = new_line.loopback;
1737
1738 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1739 info->params.clock_speed = new_line.clock_rate;
1740 else
1741 info->params.clock_speed = 0;
1742
1743 /* if network interface up, reprogram hardware */
1744 if (info->netcount)
1745 program_hw(info);
1746 return 0;
1747
1748 default:
1749 return hdlc_ioctl(dev, ifr, cmd);
1750 }
1751 }
1752
1753 /**
1754 * called by network layer when transmit timeout is detected
1755 *
1756 * dev pointer to network device structure
1757 */
1758 static void hdlcdev_tx_timeout(struct net_device *dev)
1759 {
1760 struct slgt_info *info = dev_to_port(dev);
1761 unsigned long flags;
1762
1763 DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1764
1765 dev->stats.tx_errors++;
1766 dev->stats.tx_aborted_errors++;
1767
1768 spin_lock_irqsave(&info->lock,flags);
1769 tx_stop(info);
1770 spin_unlock_irqrestore(&info->lock,flags);
1771
1772 netif_wake_queue(dev);
1773 }
1774
1775 /**
1776 * called by device driver when transmit completes
1777 * reenable network layer transmit if stopped
1778 *
1779 * info pointer to device instance information
1780 */
1781 static void hdlcdev_tx_done(struct slgt_info *info)
1782 {
1783 if (netif_queue_stopped(info->netdev))
1784 netif_wake_queue(info->netdev);
1785 }
1786
1787 /**
1788 * called by device driver when frame received
1789 * pass frame to network layer
1790 *
1791 * info pointer to device instance information
1792 * buf pointer to buffer contianing frame data
1793 * size count of data bytes in buf
1794 */
1795 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1796 {
1797 struct sk_buff *skb = dev_alloc_skb(size);
1798 struct net_device *dev = info->netdev;
1799
1800 DBGINFO(("%s hdlcdev_rx\n", dev->name));
1801
1802 if (skb == NULL) {
1803 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1804 dev->stats.rx_dropped++;
1805 return;
1806 }
1807
1808 memcpy(skb_put(skb, size), buf, size);
1809
1810 skb->protocol = hdlc_type_trans(skb, dev);
1811
1812 dev->stats.rx_packets++;
1813 dev->stats.rx_bytes += size;
1814
1815 netif_rx(skb);
1816
1817 dev->last_rx = jiffies;
1818 }
1819
1820 /**
1821 * called by device driver when adding device instance
1822 * do generic HDLC initialization
1823 *
1824 * info pointer to device instance information
1825 *
1826 * returns 0 if success, otherwise error code
1827 */
1828 static int hdlcdev_init(struct slgt_info *info)
1829 {
1830 int rc;
1831 struct net_device *dev;
1832 hdlc_device *hdlc;
1833
1834 /* allocate and initialize network and HDLC layer objects */
1835
1836 if (!(dev = alloc_hdlcdev(info))) {
1837 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1838 return -ENOMEM;
1839 }
1840
1841 /* for network layer reporting purposes only */
1842 dev->mem_start = info->phys_reg_addr;
1843 dev->mem_end = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1844 dev->irq = info->irq_level;
1845
1846 /* network layer callbacks and settings */
1847 dev->do_ioctl = hdlcdev_ioctl;
1848 dev->open = hdlcdev_open;
1849 dev->stop = hdlcdev_close;
1850 dev->tx_timeout = hdlcdev_tx_timeout;
1851 dev->watchdog_timeo = 10*HZ;
1852 dev->tx_queue_len = 50;
1853
1854 /* generic HDLC layer callbacks and settings */
1855 hdlc = dev_to_hdlc(dev);
1856 hdlc->attach = hdlcdev_attach;
1857 hdlc->xmit = hdlcdev_xmit;
1858
1859 /* register objects with HDLC layer */
1860 if ((rc = register_hdlc_device(dev))) {
1861 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1862 free_netdev(dev);
1863 return rc;
1864 }
1865
1866 info->netdev = dev;
1867 return 0;
1868 }
1869
1870 /**
1871 * called by device driver when removing device instance
1872 * do generic HDLC cleanup
1873 *
1874 * info pointer to device instance information
1875 */
1876 static void hdlcdev_exit(struct slgt_info *info)
1877 {
1878 unregister_hdlc_device(info->netdev);
1879 free_netdev(info->netdev);
1880 info->netdev = NULL;
1881 }
1882
1883 #endif /* ifdef CONFIG_HDLC */
1884
1885 /*
1886 * get async data from rx DMA buffers
1887 */
1888 static void rx_async(struct slgt_info *info)
1889 {
1890 struct tty_struct *tty = info->port.tty;
1891 struct mgsl_icount *icount = &info->icount;
1892 unsigned int start, end;
1893 unsigned char *p;
1894 unsigned char status;
1895 struct slgt_desc *bufs = info->rbufs;
1896 int i, count;
1897 int chars = 0;
1898 int stat;
1899 unsigned char ch;
1900
1901 start = end = info->rbuf_current;
1902
1903 while(desc_complete(bufs[end])) {
1904 count = desc_count(bufs[end]) - info->rbuf_index;
1905 p = bufs[end].buf + info->rbuf_index;
1906
1907 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1908 DBGDATA(info, p, count, "rx");
1909
1910 for(i=0 ; i < count; i+=2, p+=2) {
1911 ch = *p;
1912 icount->rx++;
1913
1914 stat = 0;
1915
1916 if ((status = *(p+1) & (BIT1 + BIT0))) {
1917 if (status & BIT1)
1918 icount->parity++;
1919 else if (status & BIT0)
1920 icount->frame++;
1921 /* discard char if tty control flags say so */
1922 if (status & info->ignore_status_mask)
1923 continue;
1924 if (status & BIT1)
1925 stat = TTY_PARITY;
1926 else if (status & BIT0)
1927 stat = TTY_FRAME;
1928 }
1929 if (tty) {
1930 tty_insert_flip_char(tty, ch, stat);
1931 chars++;
1932 }
1933 }
1934
1935 if (i < count) {
1936 /* receive buffer not completed */
1937 info->rbuf_index += i;
1938 mod_timer(&info->rx_timer, jiffies + 1);
1939 break;
1940 }
1941
1942 info->rbuf_index = 0;
1943 free_rbufs(info, end, end);
1944
1945 if (++end == info->rbuf_count)
1946 end = 0;
1947
1948 /* if entire list searched then no frame available */
1949 if (end == start)
1950 break;
1951 }
1952
1953 if (tty && chars)
1954 tty_flip_buffer_push(tty);
1955 }
1956
1957 /*
1958 * return next bottom half action to perform
1959 */
1960 static int bh_action(struct slgt_info *info)
1961 {
1962 unsigned long flags;
1963 int rc;
1964
1965 spin_lock_irqsave(&info->lock,flags);
1966
1967 if (info->pending_bh & BH_RECEIVE) {
1968 info->pending_bh &= ~BH_RECEIVE;
1969 rc = BH_RECEIVE;
1970 } else if (info->pending_bh & BH_TRANSMIT) {
1971 info->pending_bh &= ~BH_TRANSMIT;
1972 rc = BH_TRANSMIT;
1973 } else if (info->pending_bh & BH_STATUS) {
1974 info->pending_bh &= ~BH_STATUS;
1975 rc = BH_STATUS;
1976 } else {
1977 /* Mark BH routine as complete */
1978 info->bh_running = false;
1979 info->bh_requested = false;
1980 rc = 0;
1981 }
1982
1983 spin_unlock_irqrestore(&info->lock,flags);
1984
1985 return rc;
1986 }
1987
1988 /*
1989 * perform bottom half processing
1990 */
1991 static void bh_handler(struct work_struct *work)
1992 {
1993 struct slgt_info *info = container_of(work, struct slgt_info, task);
1994 int action;
1995
1996 if (!info)
1997 return;
1998 info->bh_running = true;
1999
2000 while((action = bh_action(info))) {
2001 switch (action) {
2002 case BH_RECEIVE:
2003 DBGBH(("%s bh receive\n", info->device_name));
2004 switch(info->params.mode) {
2005 case MGSL_MODE_ASYNC:
2006 rx_async(info);
2007 break;
2008 case MGSL_MODE_HDLC:
2009 while(rx_get_frame(info));
2010 break;
2011 case MGSL_MODE_RAW:
2012 case MGSL_MODE_MONOSYNC:
2013 case MGSL_MODE_BISYNC:
2014 while(rx_get_buf(info));
2015 break;
2016 }
2017 /* restart receiver if rx DMA buffers exhausted */
2018 if (info->rx_restart)
2019 rx_start(info);
2020 break;
2021 case BH_TRANSMIT:
2022 bh_transmit(info);
2023 break;
2024 case BH_STATUS:
2025 DBGBH(("%s bh status\n", info->device_name));
2026 info->ri_chkcount = 0;
2027 info->dsr_chkcount = 0;
2028 info->dcd_chkcount = 0;
2029 info->cts_chkcount = 0;
2030 break;
2031 default:
2032 DBGBH(("%s unknown action\n", info->device_name));
2033 break;
2034 }
2035 }
2036 DBGBH(("%s bh_handler exit\n", info->device_name));
2037 }
2038
2039 static void bh_transmit(struct slgt_info *info)
2040 {
2041 struct tty_struct *tty = info->port.tty;
2042
2043 DBGBH(("%s bh_transmit\n", info->device_name));
2044 if (tty)
2045 tty_wakeup(tty);
2046 }
2047
2048 static void dsr_change(struct slgt_info *info, unsigned short status)
2049 {
2050 if (status & BIT3) {
2051 info->signals |= SerialSignal_DSR;
2052 info->input_signal_events.dsr_up++;
2053 } else {
2054 info->signals &= ~SerialSignal_DSR;
2055 info->input_signal_events.dsr_down++;
2056 }
2057 DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
2058 if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2059 slgt_irq_off(info, IRQ_DSR);
2060 return;
2061 }
2062 info->icount.dsr++;
2063 wake_up_interruptible(&info->status_event_wait_q);
2064 wake_up_interruptible(&info->event_wait_q);
2065 info->pending_bh |= BH_STATUS;
2066 }
2067
2068 static void cts_change(struct slgt_info *info, unsigned short status)
2069 {
2070 if (status & BIT2) {
2071 info->signals |= SerialSignal_CTS;
2072 info->input_signal_events.cts_up++;
2073 } else {
2074 info->signals &= ~SerialSignal_CTS;
2075 info->input_signal_events.cts_down++;
2076 }
2077 DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2078 if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2079 slgt_irq_off(info, IRQ_CTS);
2080 return;
2081 }
2082 info->icount.cts++;
2083 wake_up_interruptible(&info->status_event_wait_q);
2084 wake_up_interruptible(&info->event_wait_q);
2085 info->pending_bh |= BH_STATUS;
2086
2087 if (info->port.flags & ASYNC_CTS_FLOW) {
2088 if (info->port.tty) {
2089 if (info->port.tty->hw_stopped) {
2090 if (info->signals & SerialSignal_CTS) {
2091 info->port.tty->hw_stopped = 0;
2092 info->pending_bh |= BH_TRANSMIT;
2093 return;
2094 }
2095 } else {
2096 if (!(info->signals & SerialSignal_CTS))
2097 info->port.tty->hw_stopped = 1;
2098 }
2099 }
2100 }
2101 }
2102
2103 static void dcd_change(struct slgt_info *info, unsigned short status)
2104 {
2105 if (status & BIT1) {
2106 info->signals |= SerialSignal_DCD;
2107 info->input_signal_events.dcd_up++;
2108 } else {
2109 info->signals &= ~SerialSignal_DCD;
2110 info->input_signal_events.dcd_down++;
2111 }
2112 DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2113 if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2114 slgt_irq_off(info, IRQ_DCD);
2115 return;
2116 }
2117 info->icount.dcd++;
2118 #if SYNCLINK_GENERIC_HDLC
2119 if (info->netcount) {
2120 if (info->signals & SerialSignal_DCD)
2121 netif_carrier_on(info->netdev);
2122 else
2123 netif_carrier_off(info->netdev);
2124 }
2125 #endif
2126 wake_up_interruptible(&info->status_event_wait_q);
2127 wake_up_interruptible(&info->event_wait_q);
2128 info->pending_bh |= BH_STATUS;
2129
2130 if (info->port.flags & ASYNC_CHECK_CD) {
2131 if (info->signals & SerialSignal_DCD)
2132 wake_up_interruptible(&info->port.open_wait);
2133 else {
2134 if (info->port.tty)
2135 tty_hangup(info->port.tty);
2136 }
2137 }
2138 }
2139
2140 static void ri_change(struct slgt_info *info, unsigned short status)
2141 {
2142 if (status & BIT0) {
2143 info->signals |= SerialSignal_RI;
2144 info->input_signal_events.ri_up++;
2145 } else {
2146 info->signals &= ~SerialSignal_RI;
2147 info->input_signal_events.ri_down++;
2148 }
2149 DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2150 if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2151 slgt_irq_off(info, IRQ_RI);
2152 return;
2153 }
2154 info->icount.rng++;
2155 wake_up_interruptible(&info->status_event_wait_q);
2156 wake_up_interruptible(&info->event_wait_q);
2157 info->pending_bh |= BH_STATUS;
2158 }
2159
2160 static void isr_serial(struct slgt_info *info)
2161 {
2162 unsigned short status = rd_reg16(info, SSR);
2163
2164 DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2165
2166 wr_reg16(info, SSR, status); /* clear pending */
2167
2168 info->irq_occurred = true;
2169
2170 if (info->params.mode == MGSL_MODE_ASYNC) {
2171 if (status & IRQ_TXIDLE) {
2172 if (info->tx_count)
2173 isr_txeom(info, status);
2174 }
2175 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2176 info->icount.brk++;
2177 /* process break detection if tty control allows */
2178 if (info->port.tty) {
2179 if (!(status & info->ignore_status_mask)) {
2180 if (info->read_status_mask & MASK_BREAK) {
2181 tty_insert_flip_char(info->port.tty, 0, TTY_BREAK);
2182 if (info->port.flags & ASYNC_SAK)
2183 do_SAK(info->port.tty);
2184 }
2185 }
2186 }
2187 }
2188 } else {
2189 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2190 isr_txeom(info, status);
2191
2192 if (status & IRQ_RXIDLE) {
2193 if (status & RXIDLE)
2194 info->icount.rxidle++;
2195 else
2196 info->icount.exithunt++;
2197 wake_up_interruptible(&info->event_wait_q);
2198 }
2199
2200 if (status & IRQ_RXOVER)
2201 rx_start(info);
2202 }
2203
2204 if (status & IRQ_DSR)
2205 dsr_change(info, status);
2206 if (status & IRQ_CTS)
2207 cts_change(info, status);
2208 if (status & IRQ_DCD)
2209 dcd_change(info, status);
2210 if (status & IRQ_RI)
2211 ri_change(info, status);
2212 }
2213
2214 static void isr_rdma(struct slgt_info *info)
2215 {
2216 unsigned int status = rd_reg32(info, RDCSR);
2217
2218 DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2219
2220 /* RDCSR (rx DMA control/status)
2221 *
2222 * 31..07 reserved
2223 * 06 save status byte to DMA buffer
2224 * 05 error
2225 * 04 eol (end of list)
2226 * 03 eob (end of buffer)
2227 * 02 IRQ enable
2228 * 01 reset
2229 * 00 enable
2230 */
2231 wr_reg32(info, RDCSR, status); /* clear pending */
2232
2233 if (status & (BIT5 + BIT4)) {
2234 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2235 info->rx_restart = true;
2236 }
2237 info->pending_bh |= BH_RECEIVE;
2238 }
2239
2240 static void isr_tdma(struct slgt_info *info)
2241 {
2242 unsigned int status = rd_reg32(info, TDCSR);
2243
2244 DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2245
2246 /* TDCSR (tx DMA control/status)
2247 *
2248 * 31..06 reserved
2249 * 05 error
2250 * 04 eol (end of list)
2251 * 03 eob (end of buffer)
2252 * 02 IRQ enable
2253 * 01 reset
2254 * 00 enable
2255 */
2256 wr_reg32(info, TDCSR, status); /* clear pending */
2257
2258 if (status & (BIT5 + BIT4 + BIT3)) {
2259 // another transmit buffer has completed
2260 // run bottom half to get more send data from user
2261 info->pending_bh |= BH_TRANSMIT;
2262 }
2263 }
2264
2265 static void isr_txeom(struct slgt_info *info, unsigned short status)
2266 {
2267 DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2268
2269 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2270 tdma_reset(info);
2271 reset_tbufs(info);
2272 if (status & IRQ_TXUNDER) {
2273 unsigned short val = rd_reg16(info, TCR);
2274 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2275 wr_reg16(info, TCR, val); /* clear reset bit */
2276 }
2277
2278 if (info->tx_active) {
2279 if (info->params.mode != MGSL_MODE_ASYNC) {
2280 if (status & IRQ_TXUNDER)
2281 info->icount.txunder++;
2282 else if (status & IRQ_TXIDLE)
2283 info->icount.txok++;
2284 }
2285
2286 info->tx_active = false;
2287 info->tx_count = 0;
2288
2289 del_timer(&info->tx_timer);
2290
2291 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2292 info->signals &= ~SerialSignal_RTS;
2293 info->drop_rts_on_tx_done = false;
2294 set_signals(info);
2295 }
2296
2297 #if SYNCLINK_GENERIC_HDLC
2298 if (info->netcount)
2299 hdlcdev_tx_done(info);
2300 else
2301 #endif
2302 {
2303 if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2304 tx_stop(info);
2305 return;
2306 }
2307 info->pending_bh |= BH_TRANSMIT;
2308 }
2309 }
2310 }
2311
2312 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2313 {
2314 struct cond_wait *w, *prev;
2315
2316 /* wake processes waiting for specific transitions */
2317 for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2318 if (w->data & changed) {
2319 w->data = state;
2320 wake_up_interruptible(&w->q);
2321 if (prev != NULL)
2322 prev->next = w->next;
2323 else
2324 info->gpio_wait_q = w->next;
2325 } else
2326 prev = w;
2327 }
2328 }
2329
2330 /* interrupt service routine
2331 *
2332 * irq interrupt number
2333 * dev_id device ID supplied during interrupt registration
2334 */
2335 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2336 {
2337 struct slgt_info *info = dev_id;
2338 unsigned int gsr;
2339 unsigned int i;
2340
2341 DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2342
2343 spin_lock(&info->lock);
2344
2345 while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2346 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2347 info->irq_occurred = true;
2348 for(i=0; i < info->port_count ; i++) {
2349 if (info->port_array[i] == NULL)
2350 continue;
2351 if (gsr & (BIT8 << i))
2352 isr_serial(info->port_array[i]);
2353 if (gsr & (BIT16 << (i*2)))
2354 isr_rdma(info->port_array[i]);
2355 if (gsr & (BIT17 << (i*2)))
2356 isr_tdma(info->port_array[i]);
2357 }
2358 }
2359
2360 if (info->gpio_present) {
2361 unsigned int state;
2362 unsigned int changed;
2363 while ((changed = rd_reg32(info, IOSR)) != 0) {
2364 DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2365 /* read latched state of GPIO signals */
2366 state = rd_reg32(info, IOVR);
2367 /* clear pending GPIO interrupt bits */
2368 wr_reg32(info, IOSR, changed);
2369 for (i=0 ; i < info->port_count ; i++) {
2370 if (info->port_array[i] != NULL)
2371 isr_gpio(info->port_array[i], changed, state);
2372 }
2373 }
2374 }
2375
2376 for(i=0; i < info->port_count ; i++) {
2377 struct slgt_info *port = info->port_array[i];
2378
2379 if (port && (port->port.count || port->netcount) &&
2380 port->pending_bh && !port->bh_running &&
2381 !port->bh_requested) {
2382 DBGISR(("%s bh queued\n", port->device_name));
2383 schedule_work(&port->task);
2384 port->bh_requested = true;
2385 }
2386 }
2387
2388 spin_unlock(&info->lock);
2389
2390 DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2391 return IRQ_HANDLED;
2392 }
2393
2394 static int startup(struct slgt_info *info)
2395 {
2396 DBGINFO(("%s startup\n", info->device_name));
2397
2398 if (info->port.flags & ASYNC_INITIALIZED)
2399 return 0;
2400
2401 if (!info->tx_buf) {
2402 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2403 if (!info->tx_buf) {
2404 DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2405 return -ENOMEM;
2406 }
2407 }
2408
2409 info->pending_bh = 0;
2410
2411 memset(&info->icount, 0, sizeof(info->icount));
2412
2413 /* program hardware for current parameters */
2414 change_params(info);
2415
2416 if (info->port.tty)
2417 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2418
2419 info->port.flags |= ASYNC_INITIALIZED;
2420
2421 return 0;
2422 }
2423
2424 /*
2425 * called by close() and hangup() to shutdown hardware
2426 */
2427 static void shutdown(struct slgt_info *info)
2428 {
2429 unsigned long flags;
2430
2431 if (!(info->port.flags & ASYNC_INITIALIZED))
2432 return;
2433
2434 DBGINFO(("%s shutdown\n", info->device_name));
2435
2436 /* clear status wait queue because status changes */
2437 /* can't happen after shutting down the hardware */
2438 wake_up_interruptible(&info->status_event_wait_q);
2439 wake_up_interruptible(&info->event_wait_q);
2440
2441 del_timer_sync(&info->tx_timer);
2442 del_timer_sync(&info->rx_timer);
2443
2444 kfree(info->tx_buf);
2445 info->tx_buf = NULL;
2446
2447 spin_lock_irqsave(&info->lock,flags);
2448
2449 tx_stop(info);
2450 rx_stop(info);
2451
2452 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2453
2454 if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
2455 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2456 set_signals(info);
2457 }
2458
2459 flush_cond_wait(&info->gpio_wait_q);
2460
2461 spin_unlock_irqrestore(&info->lock,flags);
2462
2463 if (info->port.tty)
2464 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2465
2466 info->port.flags &= ~ASYNC_INITIALIZED;
2467 }
2468
2469 static void program_hw(struct slgt_info *info)
2470 {
2471 unsigned long flags;
2472
2473 spin_lock_irqsave(&info->lock,flags);
2474
2475 rx_stop(info);
2476 tx_stop(info);
2477
2478 if (info->params.mode != MGSL_MODE_ASYNC ||
2479 info->netcount)
2480 sync_mode(info);
2481 else
2482 async_mode(info);
2483
2484 set_signals(info);
2485
2486 info->dcd_chkcount = 0;
2487 info->cts_chkcount = 0;
2488 info->ri_chkcount = 0;
2489 info->dsr_chkcount = 0;
2490
2491 slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR);
2492 get_signals(info);
2493
2494 if (info->netcount ||
2495 (info->port.tty && info->port.tty->termios->c_cflag & CREAD))
2496 rx_start(info);
2497
2498 spin_unlock_irqrestore(&info->lock,flags);
2499 }
2500
2501 /*
2502 * reconfigure adapter based on new parameters
2503 */
2504 static void change_params(struct slgt_info *info)
2505 {
2506 unsigned cflag;
2507 int bits_per_char;
2508
2509 if (!info->port.tty || !info->port.tty->termios)
2510 return;
2511 DBGINFO(("%s change_params\n", info->device_name));
2512
2513 cflag = info->port.tty->termios->c_cflag;
2514
2515 /* if B0 rate (hangup) specified then negate DTR and RTS */
2516 /* otherwise assert DTR and RTS */
2517 if (cflag & CBAUD)
2518 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2519 else
2520 info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2521
2522 /* byte size and parity */
2523
2524 switch (cflag & CSIZE) {
2525 case CS5: info->params.data_bits = 5; break;
2526 case CS6: info->params.data_bits = 6; break;
2527 case CS7: info->params.data_bits = 7; break;
2528 case CS8: info->params.data_bits = 8; break;
2529 default: info->params.data_bits = 7; break;
2530 }
2531
2532 info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2533
2534 if (cflag & PARENB)
2535 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2536 else
2537 info->params.parity = ASYNC_PARITY_NONE;
2538
2539 /* calculate number of jiffies to transmit a full
2540 * FIFO (32 bytes) at specified data rate
2541 */
2542 bits_per_char = info->params.data_bits +
2543 info->params.stop_bits + 1;
2544
2545 info->params.data_rate = tty_get_baud_rate(info->port.tty);
2546
2547 if (info->params.data_rate) {
2548 info->timeout = (32*HZ*bits_per_char) /
2549 info->params.data_rate;
2550 }
2551 info->timeout += HZ/50; /* Add .02 seconds of slop */
2552
2553 if (cflag & CRTSCTS)
2554 info->port.flags |= ASYNC_CTS_FLOW;
2555 else
2556 info->port.flags &= ~ASYNC_CTS_FLOW;
2557
2558 if (cflag & CLOCAL)
2559 info->port.flags &= ~ASYNC_CHECK_CD;
2560 else
2561 info->port.flags |= ASYNC_CHECK_CD;
2562
2563 /* process tty input control flags */
2564
2565 info->read_status_mask = IRQ_RXOVER;
2566 if (I_INPCK(info->port.tty))
2567 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2568 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2569 info->read_status_mask |= MASK_BREAK;
2570 if (I_IGNPAR(info->port.tty))
2571 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2572 if (I_IGNBRK(info->port.tty)) {
2573 info->ignore_status_mask |= MASK_BREAK;
2574 /* If ignoring parity and break indicators, ignore
2575 * overruns too. (For real raw support).
2576 */
2577 if (I_IGNPAR(info->port.tty))
2578 info->ignore_status_mask |= MASK_OVERRUN;
2579 }
2580
2581 program_hw(info);
2582 }
2583
2584 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2585 {
2586 DBGINFO(("%s get_stats\n", info->device_name));
2587 if (!user_icount) {
2588 memset(&info->icount, 0, sizeof(info->icount));
2589 } else {
2590 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2591 return -EFAULT;
2592 }
2593 return 0;
2594 }
2595
2596 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2597 {
2598 DBGINFO(("%s get_params\n", info->device_name));
2599 if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2600 return -EFAULT;
2601 return 0;
2602 }
2603
2604 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2605 {
2606 unsigned long flags;
2607 MGSL_PARAMS tmp_params;
2608
2609 DBGINFO(("%s set_params\n", info->device_name));
2610 if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2611 return -EFAULT;
2612
2613 spin_lock_irqsave(&info->lock, flags);
2614 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2615 spin_unlock_irqrestore(&info->lock, flags);
2616
2617 change_params(info);
2618
2619 return 0;
2620 }
2621
2622 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2623 {
2624 DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2625 if (put_user(info->idle_mode, idle_mode))
2626 return -EFAULT;
2627 return 0;
2628 }
2629
2630 static int set_txidle(struct slgt_info *info, int idle_mode)
2631 {
2632 unsigned long flags;
2633 DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2634 spin_lock_irqsave(&info->lock,flags);
2635 info->idle_mode = idle_mode;
2636 if (info->params.mode != MGSL_MODE_ASYNC)
2637 tx_set_idle(info);
2638 spin_unlock_irqrestore(&info->lock,flags);
2639 return 0;
2640 }
2641
2642 static int tx_enable(struct slgt_info *info, int enable)
2643 {
2644 unsigned long flags;
2645 DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2646 spin_lock_irqsave(&info->lock,flags);
2647 if (enable) {
2648 if (!info->tx_enabled)
2649 tx_start(info);
2650 } else {
2651 if (info->tx_enabled)
2652 tx_stop(info);
2653 }
2654 spin_unlock_irqrestore(&info->lock,flags);
2655 return 0;
2656 }
2657
2658 /*
2659 * abort transmit HDLC frame
2660 */
2661 static int tx_abort(struct slgt_info *info)
2662 {
2663 unsigned long flags;
2664 DBGINFO(("%s tx_abort\n", info->device_name));
2665 spin_lock_irqsave(&info->lock,flags);
2666 tdma_reset(info);
2667 spin_unlock_irqrestore(&info->lock,flags);
2668 return 0;
2669 }
2670
2671 static int rx_enable(struct slgt_info *info, int enable)
2672 {
2673 unsigned long flags;
2674 unsigned int rbuf_fill_level;
2675 DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2676 spin_lock_irqsave(&info->lock,flags);
2677 /*
2678 * enable[31..16] = receive DMA buffer fill level
2679 * 0 = noop (leave fill level unchanged)
2680 * fill level must be multiple of 4 and <= buffer size
2681 */
2682 rbuf_fill_level = ((unsigned int)enable) >> 16;
2683 if (rbuf_fill_level) {
2684 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2685 spin_unlock_irqrestore(&info->lock, flags);
2686 return -EINVAL;
2687 }
2688 info->rbuf_fill_level = rbuf_fill_level;
2689 rx_stop(info); /* restart receiver to use new fill level */
2690 }
2691
2692 /*
2693 * enable[1..0] = receiver enable command
2694 * 0 = disable
2695 * 1 = enable
2696 * 2 = enable or force hunt mode if already enabled
2697 */
2698 enable &= 3;
2699 if (enable) {
2700 if (!info->rx_enabled)
2701 rx_start(info);
2702 else if (enable == 2) {
2703 /* force hunt mode (write 1 to RCR[3]) */
2704 wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2705 }
2706 } else {
2707 if (info->rx_enabled)
2708 rx_stop(info);
2709 }
2710 spin_unlock_irqrestore(&info->lock,flags);
2711 return 0;
2712 }
2713
2714 /*
2715 * wait for specified event to occur
2716 */
2717 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2718 {
2719 unsigned long flags;
2720 int s;
2721 int rc=0;
2722 struct mgsl_icount cprev, cnow;
2723 int events;
2724 int mask;
2725 struct _input_signal_events oldsigs, newsigs;
2726 DECLARE_WAITQUEUE(wait, current);
2727
2728 if (get_user(mask, mask_ptr))
2729 return -EFAULT;
2730
2731 DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2732
2733 spin_lock_irqsave(&info->lock,flags);
2734
2735 /* return immediately if state matches requested events */
2736 get_signals(info);
2737 s = info->signals;
2738
2739 events = mask &
2740 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2741 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2742 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2743 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2744 if (events) {
2745 spin_unlock_irqrestore(&info->lock,flags);
2746 goto exit;
2747 }
2748
2749 /* save current irq counts */
2750 cprev = info->icount;
2751 oldsigs = info->input_signal_events;
2752
2753 /* enable hunt and idle irqs if needed */
2754 if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2755 unsigned short val = rd_reg16(info, SCR);
2756 if (!(val & IRQ_RXIDLE))
2757 wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2758 }
2759
2760 set_current_state(TASK_INTERRUPTIBLE);
2761 add_wait_queue(&info->event_wait_q, &wait);
2762
2763 spin_unlock_irqrestore(&info->lock,flags);
2764
2765 for(;;) {
2766 schedule();
2767 if (signal_pending(current)) {
2768 rc = -ERESTARTSYS;
2769 break;
2770 }
2771
2772 /* get current irq counts */
2773 spin_lock_irqsave(&info->lock,flags);
2774 cnow = info->icount;
2775 newsigs = info->input_signal_events;
2776 set_current_state(TASK_INTERRUPTIBLE);
2777 spin_unlock_irqrestore(&info->lock,flags);
2778
2779 /* if no change, wait aborted for some reason */
2780 if (newsigs.dsr_up == oldsigs.dsr_up &&
2781 newsigs.dsr_down == oldsigs.dsr_down &&
2782 newsigs.dcd_up == oldsigs.dcd_up &&
2783 newsigs.dcd_down == oldsigs.dcd_down &&
2784 newsigs.cts_up == oldsigs.cts_up &&
2785 newsigs.cts_down == oldsigs.cts_down &&
2786 newsigs.ri_up == oldsigs.ri_up &&
2787 newsigs.ri_down == oldsigs.ri_down &&
2788 cnow.exithunt == cprev.exithunt &&
2789 cnow.rxidle == cprev.rxidle) {
2790 rc = -EIO;
2791 break;
2792 }
2793
2794 events = mask &
2795 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) +
2796 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2797 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) +
2798 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2799 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) +
2800 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2801 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) +
2802 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) +
2803 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) +
2804 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) );
2805 if (events)
2806 break;
2807
2808 cprev = cnow;
2809 oldsigs = newsigs;
2810 }
2811
2812 remove_wait_queue(&info->event_wait_q, &wait);
2813 set_current_state(TASK_RUNNING);
2814
2815
2816 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2817 spin_lock_irqsave(&info->lock,flags);
2818 if (!waitqueue_active(&info->event_wait_q)) {
2819 /* disable enable exit hunt mode/idle rcvd IRQs */
2820 wr_reg16(info, SCR,
2821 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2822 }
2823 spin_unlock_irqrestore(&info->lock,flags);
2824 }
2825 exit:
2826 if (rc == 0)
2827 rc = put_user(events, mask_ptr);
2828 return rc;
2829 }
2830
2831 static int get_interface(struct slgt_info *info, int __user *if_mode)
2832 {
2833 DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2834 if (put_user(info->if_mode, if_mode))
2835 return -EFAULT;
2836 return 0;
2837 }
2838
2839 static int set_interface(struct slgt_info *info, int if_mode)
2840 {
2841 unsigned long flags;
2842 unsigned short val;
2843
2844 DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2845 spin_lock_irqsave(&info->lock,flags);
2846 info->if_mode = if_mode;
2847
2848 msc_set_vcr(info);
2849
2850 /* TCR (tx control) 07 1=RTS driver control */
2851 val = rd_reg16(info, TCR);
2852 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2853 val |= BIT7;
2854 else
2855 val &= ~BIT7;
2856 wr_reg16(info, TCR, val);
2857
2858 spin_unlock_irqrestore(&info->lock,flags);
2859 return 0;
2860 }
2861
2862 /*
2863 * set general purpose IO pin state and direction
2864 *
2865 * user_gpio fields:
2866 * state each bit indicates a pin state
2867 * smask set bit indicates pin state to set
2868 * dir each bit indicates a pin direction (0=input, 1=output)
2869 * dmask set bit indicates pin direction to set
2870 */
2871 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2872 {
2873 unsigned long flags;
2874 struct gpio_desc gpio;
2875 __u32 data;
2876
2877 if (!info->gpio_present)
2878 return -EINVAL;
2879 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2880 return -EFAULT;
2881 DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2882 info->device_name, gpio.state, gpio.smask,
2883 gpio.dir, gpio.dmask));
2884
2885 spin_lock_irqsave(&info->lock,flags);
2886 if (gpio.dmask) {
2887 data = rd_reg32(info, IODR);
2888 data |= gpio.dmask & gpio.dir;
2889 data &= ~(gpio.dmask & ~gpio.dir);
2890 wr_reg32(info, IODR, data);
2891 }
2892 if (gpio.smask) {
2893 data = rd_reg32(info, IOVR);
2894 data |= gpio.smask & gpio.state;
2895 data &= ~(gpio.smask & ~gpio.state);
2896 wr_reg32(info, IOVR, data);
2897 }
2898 spin_unlock_irqrestore(&info->lock,flags);
2899
2900 return 0;
2901 }
2902
2903 /*
2904 * get general purpose IO pin state and direction
2905 */
2906 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2907 {
2908 struct gpio_desc gpio;
2909 if (!info->gpio_present)
2910 return -EINVAL;
2911 gpio.state = rd_reg32(info, IOVR);
2912 gpio.smask = 0xffffffff;
2913 gpio.dir = rd_reg32(info, IODR);
2914 gpio.dmask = 0xffffffff;
2915 if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2916 return -EFAULT;
2917 DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2918 info->device_name, gpio.state, gpio.dir));
2919 return 0;
2920 }
2921
2922 /*
2923 * conditional wait facility
2924 */
2925 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2926 {
2927 init_waitqueue_head(&w->q);
2928 init_waitqueue_entry(&w->wait, current);
2929 w->data = data;
2930 }
2931
2932 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2933 {
2934 set_current_state(TASK_INTERRUPTIBLE);
2935 add_wait_queue(&w->q, &w->wait);
2936 w->next = *head;
2937 *head = w;
2938 }
2939
2940 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
2941 {
2942 struct cond_wait *w, *prev;
2943 remove_wait_queue(&cw->q, &cw->wait);
2944 set_current_state(TASK_RUNNING);
2945 for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
2946 if (w == cw) {
2947 if (prev != NULL)
2948 prev->next = w->next;
2949 else
2950 *head = w->next;
2951 break;
2952 }
2953 }
2954 }
2955
2956 static void flush_cond_wait(struct cond_wait **head)
2957 {
2958 while (*head != NULL) {
2959 wake_up_interruptible(&(*head)->q);
2960 *head = (*head)->next;
2961 }
2962 }
2963
2964 /*
2965 * wait for general purpose I/O pin(s) to enter specified state
2966 *
2967 * user_gpio fields:
2968 * state - bit indicates target pin state
2969 * smask - set bit indicates watched pin
2970 *
2971 * The wait ends when at least one watched pin enters the specified
2972 * state. When 0 (no error) is returned, user_gpio->state is set to the
2973 * state of all GPIO pins when the wait ends.
2974 *
2975 * Note: Each pin may be a dedicated input, dedicated output, or
2976 * configurable input/output. The number and configuration of pins
2977 * varies with the specific adapter model. Only input pins (dedicated
2978 * or configured) can be monitored with this function.
2979 */
2980 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2981 {
2982 unsigned long flags;
2983 int rc = 0;
2984 struct gpio_desc gpio;
2985 struct cond_wait wait;
2986 u32 state;
2987
2988 if (!info->gpio_present)
2989 return -EINVAL;
2990 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2991 return -EFAULT;
2992 DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
2993 info->device_name, gpio.state, gpio.smask));
2994 /* ignore output pins identified by set IODR bit */
2995 if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
2996 return -EINVAL;
2997 init_cond_wait(&wait, gpio.smask);
2998
2999 spin_lock_irqsave(&info->lock, flags);
3000 /* enable interrupts for watched pins */
3001 wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3002 /* get current pin states */
3003 state = rd_reg32(info, IOVR);
3004
3005 if (gpio.smask & ~(state ^ gpio.state)) {
3006 /* already in target state */
3007 gpio.state = state;
3008 } else {
3009 /* wait for target state */
3010 add_cond_wait(&info->gpio_wait_q, &wait);
3011 spin_unlock_irqrestore(&info->lock, flags);
3012 schedule();
3013 if (signal_pending(current))
3014 rc = -ERESTARTSYS;
3015 else
3016 gpio.state = wait.data;
3017 spin_lock_irqsave(&info->lock, flags);
3018 remove_cond_wait(&info->gpio_wait_q, &wait);
3019 }
3020
3021 /* disable all GPIO interrupts if no waiting processes */
3022 if (info->gpio_wait_q == NULL)
3023 wr_reg32(info, IOER, 0);
3024 spin_unlock_irqrestore(&info->lock,flags);
3025
3026 if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3027 rc = -EFAULT;
3028 return rc;
3029 }
3030
3031 static int modem_input_wait(struct slgt_info *info,int arg)
3032 {
3033 unsigned long flags;
3034 int rc;
3035 struct mgsl_icount cprev, cnow;
3036 DECLARE_WAITQUEUE(wait, current);
3037
3038 /* save current irq counts */
3039 spin_lock_irqsave(&info->lock,flags);
3040 cprev = info->icount;
3041 add_wait_queue(&info->status_event_wait_q, &wait);
3042 set_current_state(TASK_INTERRUPTIBLE);
3043 spin_unlock_irqrestore(&info->lock,flags);
3044
3045 for(;;) {
3046 schedule();
3047 if (signal_pending(current)) {
3048 rc = -ERESTARTSYS;
3049 break;
3050 }
3051
3052 /* get new irq counts */
3053 spin_lock_irqsave(&info->lock,flags);
3054 cnow = info->icount;
3055 set_current_state(TASK_INTERRUPTIBLE);
3056 spin_unlock_irqrestore(&info->lock,flags);
3057
3058 /* if no change, wait aborted for some reason */
3059 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3060 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3061 rc = -EIO;
3062 break;
3063 }
3064
3065 /* check for change in caller specified modem input */
3066 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3067 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3068 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) ||
3069 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3070 rc = 0;
3071 break;
3072 }
3073
3074 cprev = cnow;
3075 }
3076 remove_wait_queue(&info->status_event_wait_q, &wait);
3077 set_current_state(TASK_RUNNING);
3078 return rc;
3079 }
3080
3081 /*
3082 * return state of serial control and status signals
3083 */
3084 static int tiocmget(struct tty_struct *tty, struct file *file)
3085 {
3086 struct slgt_info *info = tty->driver_data;
3087 unsigned int result;
3088 unsigned long flags;
3089
3090 spin_lock_irqsave(&info->lock,flags);
3091 get_signals(info);
3092 spin_unlock_irqrestore(&info->lock,flags);
3093
3094 result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3095 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3096 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3097 ((info->signals & SerialSignal_RI) ? TIOCM_RNG:0) +
3098 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3099 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3100
3101 DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3102 return result;
3103 }
3104
3105 /*
3106 * set modem control signals (DTR/RTS)
3107 *
3108 * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3109 * TIOCMSET = set/clear signal values
3110 * value bit mask for command
3111 */
3112 static int tiocmset(struct tty_struct *tty, struct file *file,
3113 unsigned int set, unsigned int clear)
3114 {
3115 struct slgt_info *info = tty->driver_data;
3116 unsigned long flags;
3117
3118 DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3119
3120 if (set & TIOCM_RTS)
3121 info->signals |= SerialSignal_RTS;
3122 if (set & TIOCM_DTR)
3123 info->signals |= SerialSignal_DTR;
3124 if (clear & TIOCM_RTS)
3125 info->signals &= ~SerialSignal_RTS;
3126 if (clear & TIOCM_DTR)
3127 info->signals &= ~SerialSignal_DTR;
3128
3129 spin_lock_irqsave(&info->lock,flags);
3130 set_signals(info);
3131 spin_unlock_irqrestore(&info->lock,flags);
3132 return 0;
3133 }
3134
3135 /*
3136 * block current process until the device is ready to open
3137 */
3138 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3139 struct slgt_info *info)
3140 {
3141 DECLARE_WAITQUEUE(wait, current);
3142 int retval;
3143 bool do_clocal = false;
3144 bool extra_count = false;
3145 unsigned long flags;
3146
3147 DBGINFO(("%s block_til_ready\n", tty->driver->name));
3148
3149 if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3150 /* nonblock mode is set or port is not enabled */
3151 info->port.flags |= ASYNC_NORMAL_ACTIVE;
3152 return 0;
3153 }
3154
3155 if (tty->termios->c_cflag & CLOCAL)
3156 do_clocal = true;
3157
3158 /* Wait for carrier detect and the line to become
3159 * free (i.e., not in use by the callout). While we are in
3160 * this loop, info->port.count is dropped by one, so that
3161 * close() knows when to free things. We restore it upon
3162 * exit, either normal or abnormal.
3163 */
3164
3165 retval = 0;
3166 add_wait_queue(&info->port.open_wait, &wait);
3167
3168 spin_lock_irqsave(&info->lock, flags);
3169 if (!tty_hung_up_p(filp)) {
3170 extra_count = true;
3171 info->port.count--;
3172 }
3173 spin_unlock_irqrestore(&info->lock, flags);
3174 info->port.blocked_open++;
3175
3176 while (1) {
3177 if ((tty->termios->c_cflag & CBAUD)) {
3178 spin_lock_irqsave(&info->lock,flags);
3179 info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3180 set_signals(info);
3181 spin_unlock_irqrestore(&info->lock,flags);
3182 }
3183
3184 set_current_state(TASK_INTERRUPTIBLE);
3185
3186 if (tty_hung_up_p(filp) || !(info->port.flags & ASYNC_INITIALIZED)){
3187 retval = (info->port.flags & ASYNC_HUP_NOTIFY) ?
3188 -EAGAIN : -ERESTARTSYS;
3189 break;
3190 }
3191
3192 spin_lock_irqsave(&info->lock,flags);
3193 get_signals(info);
3194 spin_unlock_irqrestore(&info->lock,flags);
3195
3196 if (!(info->port.flags & ASYNC_CLOSING) &&
3197 (do_clocal || (info->signals & SerialSignal_DCD)) ) {
3198 break;
3199 }
3200
3201 if (signal_pending(current)) {
3202 retval = -ERESTARTSYS;
3203 break;
3204 }
3205
3206 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3207 schedule();
3208 }
3209
3210 set_current_state(TASK_RUNNING);
3211 remove_wait_queue(&info->port.open_wait, &wait);
3212
3213 if (extra_count)
3214 info->port.count++;
3215 info->port.blocked_open--;
3216
3217 if (!retval)
3218 info->port.flags |= ASYNC_NORMAL_ACTIVE;
3219
3220 DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3221 return retval;
3222 }
3223
3224 static int alloc_tmp_rbuf(struct slgt_info *info)
3225 {
3226 info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3227 if (info->tmp_rbuf == NULL)
3228 return -ENOMEM;
3229 return 0;
3230 }
3231
3232 static void free_tmp_rbuf(struct slgt_info *info)
3233 {
3234 kfree(info->tmp_rbuf);
3235 info->tmp_rbuf = NULL;
3236 }
3237
3238 /*
3239 * allocate DMA descriptor lists.
3240 */
3241 static int alloc_desc(struct slgt_info *info)
3242 {
3243 unsigned int i;
3244 unsigned int pbufs;
3245
3246 /* allocate memory to hold descriptor lists */
3247 info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3248 if (info->bufs == NULL)
3249 return -ENOMEM;
3250
3251 memset(info->bufs, 0, DESC_LIST_SIZE);
3252
3253 info->rbufs = (struct slgt_desc*)info->bufs;
3254 info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3255
3256 pbufs = (unsigned int)info->bufs_dma_addr;
3257
3258 /*
3259 * Build circular lists of descriptors
3260 */
3261
3262 for (i=0; i < info->rbuf_count; i++) {
3263 /* physical address of this descriptor */
3264 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3265
3266 /* physical address of next descriptor */
3267 if (i == info->rbuf_count - 1)
3268 info->rbufs[i].next = cpu_to_le32(pbufs);
3269 else
3270 info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3271 set_desc_count(info->rbufs[i], DMABUFSIZE);
3272 }
3273
3274 for (i=0; i < info->tbuf_count; i++) {
3275 /* physical address of this descriptor */
3276 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3277
3278 /* physical address of next descriptor */
3279 if (i == info->tbuf_count - 1)
3280 info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3281 else
3282 info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3283 }
3284
3285 return 0;
3286 }
3287
3288 static void free_desc(struct slgt_info *info)
3289 {
3290 if (info->bufs != NULL) {
3291 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3292 info->bufs = NULL;
3293 info->rbufs = NULL;
3294 info->tbufs = NULL;
3295 }
3296 }
3297
3298 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3299 {
3300 int i;
3301 for (i=0; i < count; i++) {
3302 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3303 return -ENOMEM;
3304 bufs[i].pbuf = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3305 }
3306 return 0;
3307 }
3308
3309 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3310 {
3311 int i;
3312 for (i=0; i < count; i++) {
3313 if (bufs[i].buf == NULL)
3314 continue;
3315 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3316 bufs[i].buf = NULL;
3317 }
3318 }
3319
3320 static int alloc_dma_bufs(struct slgt_info *info)
3321 {
3322 info->rbuf_count = 32;
3323 info->tbuf_count = 32;
3324
3325 if (alloc_desc(info) < 0 ||
3326 alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3327 alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3328 alloc_tmp_rbuf(info) < 0) {
3329 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3330 return -ENOMEM;
3331 }
3332 reset_rbufs(info);
3333 return 0;
3334 }
3335
3336 static void free_dma_bufs(struct slgt_info *info)
3337 {
3338 if (info->bufs) {
3339 free_bufs(info, info->rbufs, info->rbuf_count);
3340 free_bufs(info, info->tbufs, info->tbuf_count);
3341 free_desc(info);
3342 }
3343 free_tmp_rbuf(info);
3344 }
3345
3346 static int claim_resources(struct slgt_info *info)
3347 {
3348 if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3349 DBGERR(("%s reg addr conflict, addr=%08X\n",
3350 info->device_name, info->phys_reg_addr));
3351 info->init_error = DiagStatus_AddressConflict;
3352 goto errout;
3353 }
3354 else
3355 info->reg_addr_requested = true;
3356
3357 info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3358 if (!info->reg_addr) {
3359 DBGERR(("%s cant map device registers, addr=%08X\n",
3360 info->device_name, info->phys_reg_addr));
3361 info->init_error = DiagStatus_CantAssignPciResources;
3362 goto errout;
3363 }
3364 return 0;
3365
3366 errout:
3367 release_resources(info);
3368 return -ENODEV;
3369 }
3370
3371 static void release_resources(struct slgt_info *info)
3372 {
3373 if (info->irq_requested) {
3374 free_irq(info->irq_level, info);
3375 info->irq_requested = false;
3376 }
3377
3378 if (info->reg_addr_requested) {
3379 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3380 info->reg_addr_requested = false;
3381 }
3382
3383 if (info->reg_addr) {
3384 iounmap(info->reg_addr);
3385 info->reg_addr = NULL;
3386 }
3387 }
3388
3389 /* Add the specified device instance data structure to the
3390 * global linked list of devices and increment the device count.
3391 */
3392 static void add_device(struct slgt_info *info)
3393 {
3394 char *devstr;
3395
3396 info->next_device = NULL;
3397 info->line = slgt_device_count;
3398 sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3399
3400 if (info->line < MAX_DEVICES) {
3401 if (maxframe[info->line])
3402 info->max_frame_size = maxframe[info->line];
3403 }
3404
3405 slgt_device_count++;
3406
3407 if (!slgt_device_list)
3408 slgt_device_list = info;
3409 else {
3410 struct slgt_info *current_dev = slgt_device_list;
3411 while(current_dev->next_device)
3412 current_dev = current_dev->next_device;
3413 current_dev->next_device = info;
3414 }
3415
3416 if (info->max_frame_size < 4096)
3417 info->max_frame_size = 4096;
3418 else if (info->max_frame_size > 65535)
3419 info->max_frame_size = 65535;
3420
3421 switch(info->pdev->device) {
3422 case SYNCLINK_GT_DEVICE_ID:
3423 devstr = "GT";
3424 break;
3425 case SYNCLINK_GT2_DEVICE_ID:
3426 devstr = "GT2";
3427 break;
3428 case SYNCLINK_GT4_DEVICE_ID:
3429 devstr = "GT4";
3430 break;
3431 case SYNCLINK_AC_DEVICE_ID:
3432 devstr = "AC";
3433 info->params.mode = MGSL_MODE_ASYNC;
3434 break;
3435 default:
3436 devstr = "(unknown model)";
3437 }
3438 printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3439 devstr, info->device_name, info->phys_reg_addr,
3440 info->irq_level, info->max_frame_size);
3441
3442 #if SYNCLINK_GENERIC_HDLC
3443 hdlcdev_init(info);
3444 #endif
3445 }
3446
3447 /*
3448 * allocate device instance structure, return NULL on failure
3449 */
3450 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3451 {
3452 struct slgt_info *info;
3453
3454 info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3455
3456 if (!info) {
3457 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3458 driver_name, adapter_num, port_num));
3459 } else {
3460 tty_port_init(&info->port);
3461 info->magic = MGSL_MAGIC;
3462 INIT_WORK(&info->task, bh_handler);
3463 info->max_frame_size = 4096;
3464 info->rbuf_fill_level = DMABUFSIZE;
3465 info->port.close_delay = 5*HZ/10;
3466 info->port.closing_wait = 30*HZ;
3467 init_waitqueue_head(&info->status_event_wait_q);
3468 init_waitqueue_head(&info->event_wait_q);
3469 spin_lock_init(&info->netlock);
3470 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3471 info->idle_mode = HDLC_TXIDLE_FLAGS;
3472 info->adapter_num = adapter_num;
3473 info->port_num = port_num;
3474
3475 setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3476 setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3477
3478 /* Copy configuration info to device instance data */
3479 info->pdev = pdev;
3480 info->irq_level = pdev->irq;
3481 info->phys_reg_addr = pci_resource_start(pdev,0);
3482
3483 info->bus_type = MGSL_BUS_TYPE_PCI;
3484 info->irq_flags = IRQF_SHARED;
3485
3486 info->init_error = -1; /* assume error, set to 0 on successful init */
3487 }
3488
3489 return info;
3490 }
3491
3492 static void device_init(int adapter_num, struct pci_dev *pdev)
3493 {
3494 struct slgt_info *port_array[SLGT_MAX_PORTS];
3495 int i;
3496 int port_count = 1;
3497
3498 if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3499 port_count = 2;
3500 else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3501 port_count = 4;
3502
3503 /* allocate device instances for all ports */
3504 for (i=0; i < port_count; ++i) {
3505 port_array[i] = alloc_dev(adapter_num, i, pdev);
3506 if (port_array[i] == NULL) {
3507 for (--i; i >= 0; --i)
3508 kfree(port_array[i]);
3509 return;
3510 }
3511 }
3512
3513 /* give copy of port_array to all ports and add to device list */
3514 for (i=0; i < port_count; ++i) {
3515 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3516 add_device(port_array[i]);
3517 port_array[i]->port_count = port_count;
3518 spin_lock_init(&port_array[i]->lock);
3519 }
3520
3521 /* Allocate and claim adapter resources */
3522 if (!claim_resources(port_array[0])) {
3523
3524 alloc_dma_bufs(port_array[0]);
3525
3526 /* copy resource information from first port to others */
3527 for (i = 1; i < port_count; ++i) {
3528 port_array[i]->lock = port_array[0]->lock;
3529 port_array[i]->irq_level = port_array[0]->irq_level;
3530 port_array[i]->reg_addr = port_array[0]->reg_addr;
3531 alloc_dma_bufs(port_array[i]);
3532 }
3533
3534 if (request_irq(port_array[0]->irq_level,
3535 slgt_interrupt,
3536 port_array[0]->irq_flags,
3537 port_array[0]->device_name,
3538 port_array[0]) < 0) {
3539 DBGERR(("%s request_irq failed IRQ=%d\n",
3540 port_array[0]->device_name,
3541 port_array[0]->irq_level));
3542 } else {
3543 port_array[0]->irq_requested = true;
3544 adapter_test(port_array[0]);
3545 for (i=1 ; i < port_count ; i++) {
3546 port_array[i]->init_error = port_array[0]->init_error;
3547 port_array[i]->gpio_present = port_array[0]->gpio_present;
3548 }
3549 }
3550 }
3551
3552 for (i=0; i < port_count; ++i)
3553 tty_register_device(serial_driver, port_array[i]->line, &(port_array[i]->pdev->dev));
3554 }
3555
3556 static int __devinit init_one(struct pci_dev *dev,
3557 const struct pci_device_id *ent)
3558 {
3559 if (pci_enable_device(dev)) {
3560 printk("error enabling pci device %p\n", dev);
3561 return -EIO;
3562 }
3563 pci_set_master(dev);
3564 device_init(slgt_device_count, dev);
3565 return 0;
3566 }
3567
3568 static void __devexit remove_one(struct pci_dev *dev)
3569 {
3570 }
3571
3572 static const struct tty_operations ops = {
3573 .open = open,
3574 .close = close,
3575 .write = write,
3576 .put_char = put_char,
3577 .flush_chars = flush_chars,
3578 .write_room = write_room,
3579 .chars_in_buffer = chars_in_buffer,
3580 .flush_buffer = flush_buffer,
3581 .ioctl = ioctl,
3582 .compat_ioctl = slgt_compat_ioctl,
3583 .throttle = throttle,
3584 .unthrottle = unthrottle,
3585 .send_xchar = send_xchar,
3586 .break_ctl = set_break,
3587 .wait_until_sent = wait_until_sent,
3588 .read_proc = read_proc,
3589 .set_termios = set_termios,
3590 .stop = tx_hold,
3591 .start = tx_release,
3592 .hangup = hangup,
3593 .tiocmget = tiocmget,
3594 .tiocmset = tiocmset,
3595 };
3596
3597 static void slgt_cleanup(void)
3598 {
3599 int rc;
3600 struct slgt_info *info;
3601 struct slgt_info *tmp;
3602
3603 printk("unload %s %s\n", driver_name, driver_version);
3604
3605 if (serial_driver) {
3606 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3607 tty_unregister_device(serial_driver, info->line);
3608 if ((rc = tty_unregister_driver(serial_driver)))
3609 DBGERR(("tty_unregister_driver error=%d\n", rc));
3610 put_tty_driver(serial_driver);
3611 }
3612
3613 /* reset devices */
3614 info = slgt_device_list;
3615 while(info) {
3616 reset_port(info);
3617 info = info->next_device;
3618 }
3619
3620 /* release devices */
3621 info = slgt_device_list;
3622 while(info) {
3623 #if SYNCLINK_GENERIC_HDLC
3624 hdlcdev_exit(info);
3625 #endif
3626 free_dma_bufs(info);
3627 free_tmp_rbuf(info);
3628 if (info->port_num == 0)
3629 release_resources(info);
3630 tmp = info;
3631 info = info->next_device;
3632 kfree(tmp);
3633 }
3634
3635 if (pci_registered)
3636 pci_unregister_driver(&pci_driver);
3637 }
3638
3639 /*
3640 * Driver initialization entry point.
3641 */
3642 static int __init slgt_init(void)
3643 {
3644 int rc;
3645
3646 printk("%s %s\n", driver_name, driver_version);
3647
3648 serial_driver = alloc_tty_driver(MAX_DEVICES);
3649 if (!serial_driver) {
3650 printk("%s can't allocate tty driver\n", driver_name);
3651 return -ENOMEM;
3652 }
3653
3654 /* Initialize the tty_driver structure */
3655
3656 serial_driver->owner = THIS_MODULE;
3657 serial_driver->driver_name = tty_driver_name;
3658 serial_driver->name = tty_dev_prefix;
3659 serial_driver->major = ttymajor;
3660 serial_driver->minor_start = 64;
3661 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3662 serial_driver->subtype = SERIAL_TYPE_NORMAL;
3663 serial_driver->init_termios = tty_std_termios;
3664 serial_driver->init_termios.c_cflag =
3665 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3666 serial_driver->init_termios.c_ispeed = 9600;
3667 serial_driver->init_termios.c_ospeed = 9600;
3668 serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3669 tty_set_operations(serial_driver, &ops);
3670 if ((rc = tty_register_driver(serial_driver)) < 0) {
3671 DBGERR(("%s can't register serial driver\n", driver_name));
3672 put_tty_driver(serial_driver);
3673 serial_driver = NULL;
3674 goto error;
3675 }
3676
3677 printk("%s %s, tty major#%d\n",
3678 driver_name, driver_version,
3679 serial_driver->major);
3680
3681 slgt_device_count = 0;
3682 if ((rc = pci_register_driver(&pci_driver)) < 0) {
3683 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3684 goto error;
3685 }
3686 pci_registered = true;
3687
3688 if (!slgt_device_list)
3689 printk("%s no devices found\n",driver_name);
3690
3691 return 0;
3692
3693 error:
3694 slgt_cleanup();
3695 return rc;
3696 }
3697
3698 static void __exit slgt_exit(void)
3699 {
3700 slgt_cleanup();
3701 }
3702
3703 module_init(slgt_init);
3704 module_exit(slgt_exit);
3705
3706 /*
3707 * register access routines
3708 */
3709
3710 #define CALC_REGADDR() \
3711 unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3712 if (addr >= 0x80) \
3713 reg_addr += (info->port_num) * 32;
3714
3715 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3716 {
3717 CALC_REGADDR();
3718 return readb((void __iomem *)reg_addr);
3719 }
3720
3721 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3722 {
3723 CALC_REGADDR();
3724 writeb(value, (void __iomem *)reg_addr);
3725 }
3726
3727 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3728 {
3729 CALC_REGADDR();
3730 return readw((void __iomem *)reg_addr);
3731 }
3732
3733 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3734 {
3735 CALC_REGADDR();
3736 writew(value, (void __iomem *)reg_addr);
3737 }
3738
3739 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3740 {
3741 CALC_REGADDR();
3742 return readl((void __iomem *)reg_addr);
3743 }
3744
3745 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3746 {
3747 CALC_REGADDR();
3748 writel(value, (void __iomem *)reg_addr);
3749 }
3750
3751 static void rdma_reset(struct slgt_info *info)
3752 {
3753 unsigned int i;
3754
3755 /* set reset bit */
3756 wr_reg32(info, RDCSR, BIT1);
3757
3758 /* wait for enable bit cleared */
3759 for(i=0 ; i < 1000 ; i++)
3760 if (!(rd_reg32(info, RDCSR) & BIT0))
3761 break;
3762 }
3763
3764 static void tdma_reset(struct slgt_info *info)
3765 {
3766 unsigned int i;
3767
3768 /* set reset bit */
3769 wr_reg32(info, TDCSR, BIT1);
3770
3771 /* wait for enable bit cleared */
3772 for(i=0 ; i < 1000 ; i++)
3773 if (!(rd_reg32(info, TDCSR) & BIT0))
3774 break;
3775 }
3776
3777 /*
3778 * enable internal loopback
3779 * TxCLK and RxCLK are generated from BRG
3780 * and TxD is looped back to RxD internally.
3781 */
3782 static void enable_loopback(struct slgt_info *info)
3783 {
3784 /* SCR (serial control) BIT2=looopback enable */
3785 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3786
3787 if (info->params.mode != MGSL_MODE_ASYNC) {
3788 /* CCR (clock control)
3789 * 07..05 tx clock source (010 = BRG)
3790 * 04..02 rx clock source (010 = BRG)
3791 * 01 auxclk enable (0 = disable)
3792 * 00 BRG enable (1 = enable)
3793 *
3794 * 0100 1001
3795 */
3796 wr_reg8(info, CCR, 0x49);
3797
3798 /* set speed if available, otherwise use default */
3799 if (info->params.clock_speed)
3800 set_rate(info, info->params.clock_speed);
3801 else
3802 set_rate(info, 3686400);
3803 }
3804 }
3805
3806 /*
3807 * set baud rate generator to specified rate
3808 */
3809 static void set_rate(struct slgt_info *info, u32 rate)
3810 {
3811 unsigned int div;
3812 static unsigned int osc = 14745600;
3813
3814 /* div = osc/rate - 1
3815 *
3816 * Round div up if osc/rate is not integer to
3817 * force to next slowest rate.
3818 */
3819
3820 if (rate) {
3821 div = osc/rate;
3822 if (!(osc % rate) && div)
3823 div--;
3824 wr_reg16(info, BDR, (unsigned short)div);
3825 }
3826 }
3827
3828 static void rx_stop(struct slgt_info *info)
3829 {
3830 unsigned short val;
3831
3832 /* disable and reset receiver */
3833 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3834 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3835 wr_reg16(info, RCR, val); /* clear reset bit */
3836
3837 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3838
3839 /* clear pending rx interrupts */
3840 wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3841
3842 rdma_reset(info);
3843
3844 info->rx_enabled = false;
3845 info->rx_restart = false;
3846 }
3847
3848 static void rx_start(struct slgt_info *info)
3849 {
3850 unsigned short val;
3851
3852 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3853
3854 /* clear pending rx overrun IRQ */
3855 wr_reg16(info, SSR, IRQ_RXOVER);
3856
3857 /* reset and disable receiver */
3858 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3859 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3860 wr_reg16(info, RCR, val); /* clear reset bit */
3861
3862 rdma_reset(info);
3863 reset_rbufs(info);
3864
3865 /* set 1st descriptor address */
3866 wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3867
3868 if (info->params.mode != MGSL_MODE_ASYNC) {
3869 /* enable rx DMA and DMA interrupt */
3870 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3871 } else {
3872 /* enable saving of rx status, rx DMA and DMA interrupt */
3873 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3874 }
3875
3876 slgt_irq_on(info, IRQ_RXOVER);
3877
3878 /* enable receiver */
3879 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
3880
3881 info->rx_restart = false;
3882 info->rx_enabled = true;
3883 }
3884
3885 static void tx_start(struct slgt_info *info)
3886 {
3887 if (!info->tx_enabled) {
3888 wr_reg16(info, TCR,
3889 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
3890 info->tx_enabled = true;
3891 }
3892
3893 if (info->tx_count) {
3894 info->drop_rts_on_tx_done = false;
3895
3896 if (info->params.mode != MGSL_MODE_ASYNC) {
3897 if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
3898 get_signals(info);
3899 if (!(info->signals & SerialSignal_RTS)) {
3900 info->signals |= SerialSignal_RTS;
3901 set_signals(info);
3902 info->drop_rts_on_tx_done = true;
3903 }
3904 }
3905
3906 slgt_irq_off(info, IRQ_TXDATA);
3907 slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
3908 /* clear tx idle and underrun status bits */
3909 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3910 if (info->params.mode == MGSL_MODE_HDLC)
3911 mod_timer(&info->tx_timer, jiffies +
3912 msecs_to_jiffies(5000));
3913 } else {
3914 slgt_irq_off(info, IRQ_TXDATA);
3915 slgt_irq_on(info, IRQ_TXIDLE);
3916 /* clear tx idle status bit */
3917 wr_reg16(info, SSR, IRQ_TXIDLE);
3918 }
3919 tdma_start(info);
3920 info->tx_active = true;
3921 }
3922 }
3923
3924 /*
3925 * start transmit DMA if inactive and there are unsent buffers
3926 */
3927 static void tdma_start(struct slgt_info *info)
3928 {
3929 unsigned int i;
3930
3931 if (rd_reg32(info, TDCSR) & BIT0)
3932 return;
3933
3934 /* transmit DMA inactive, check for unsent buffers */
3935 i = info->tbuf_start;
3936 while (!desc_count(info->tbufs[i])) {
3937 if (++i == info->tbuf_count)
3938 i = 0;
3939 if (i == info->tbuf_current)
3940 return;
3941 }
3942 info->tbuf_start = i;
3943
3944 /* there are unsent buffers, start transmit DMA */
3945
3946 /* reset needed if previous error condition */
3947 tdma_reset(info);
3948
3949 /* set 1st descriptor address */
3950 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
3951 wr_reg32(info, TDCSR, BIT2 + BIT0); /* IRQ + DMA enable */
3952 }
3953
3954 static void tx_stop(struct slgt_info *info)
3955 {
3956 unsigned short val;
3957
3958 del_timer(&info->tx_timer);
3959
3960 tdma_reset(info);
3961
3962 /* reset and disable transmitter */
3963 val = rd_reg16(info, TCR) & ~BIT1; /* clear enable bit */
3964 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
3965
3966 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
3967
3968 /* clear tx idle and underrun status bit */
3969 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
3970
3971 reset_tbufs(info);
3972
3973 info->tx_enabled = false;
3974 info->tx_active = false;
3975 }
3976
3977 static void reset_port(struct slgt_info *info)
3978 {
3979 if (!info->reg_addr)
3980 return;
3981
3982 tx_stop(info);
3983 rx_stop(info);
3984
3985 info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
3986 set_signals(info);
3987
3988 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
3989 }
3990
3991 static void reset_adapter(struct slgt_info *info)
3992 {
3993 int i;
3994 for (i=0; i < info->port_count; ++i) {
3995 if (info->port_array[i])
3996 reset_port(info->port_array[i]);
3997 }
3998 }
3999
4000 static void async_mode(struct slgt_info *info)
4001 {
4002 unsigned short val;
4003
4004 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4005 tx_stop(info);
4006 rx_stop(info);
4007
4008 /* TCR (tx control)
4009 *
4010 * 15..13 mode, 010=async
4011 * 12..10 encoding, 000=NRZ
4012 * 09 parity enable
4013 * 08 1=odd parity, 0=even parity
4014 * 07 1=RTS driver control
4015 * 06 1=break enable
4016 * 05..04 character length
4017 * 00=5 bits
4018 * 01=6 bits
4019 * 10=7 bits
4020 * 11=8 bits
4021 * 03 0=1 stop bit, 1=2 stop bits
4022 * 02 reset
4023 * 01 enable
4024 * 00 auto-CTS enable
4025 */
4026 val = 0x4000;
4027
4028 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4029 val |= BIT7;
4030
4031 if (info->params.parity != ASYNC_PARITY_NONE) {
4032 val |= BIT9;
4033 if (info->params.parity == ASYNC_PARITY_ODD)
4034 val |= BIT8;
4035 }
4036
4037 switch (info->params.data_bits)
4038 {
4039 case 6: val |= BIT4; break;
4040 case 7: val |= BIT5; break;
4041 case 8: val |= BIT5 + BIT4; break;
4042 }
4043
4044 if (info->params.stop_bits != 1)
4045 val |= BIT3;
4046
4047 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4048 val |= BIT0;
4049
4050 wr_reg16(info, TCR, val);
4051
4052 /* RCR (rx control)
4053 *
4054 * 15..13 mode, 010=async
4055 * 12..10 encoding, 000=NRZ
4056 * 09 parity enable
4057 * 08 1=odd parity, 0=even parity
4058 * 07..06 reserved, must be 0
4059 * 05..04 character length
4060 * 00=5 bits
4061 * 01=6 bits
4062 * 10=7 bits
4063 * 11=8 bits
4064 * 03 reserved, must be zero
4065 * 02 reset
4066 * 01 enable
4067 * 00 auto-DCD enable
4068 */
4069 val = 0x4000;
4070
4071 if (info->params.parity != ASYNC_PARITY_NONE) {
4072 val |= BIT9;
4073 if (info->params.parity == ASYNC_PARITY_ODD)
4074 val |= BIT8;
4075 }
4076
4077 switch (info->params.data_bits)
4078 {
4079 case 6: val |= BIT4; break;
4080 case 7: val |= BIT5; break;
4081 case 8: val |= BIT5 + BIT4; break;
4082 }
4083
4084 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4085 val |= BIT0;
4086
4087 wr_reg16(info, RCR, val);
4088
4089 /* CCR (clock control)
4090 *
4091 * 07..05 011 = tx clock source is BRG/16
4092 * 04..02 010 = rx clock source is BRG
4093 * 01 0 = auxclk disabled
4094 * 00 1 = BRG enabled
4095 *
4096 * 0110 1001
4097 */
4098 wr_reg8(info, CCR, 0x69);
4099
4100 msc_set_vcr(info);
4101
4102 /* SCR (serial control)
4103 *
4104 * 15 1=tx req on FIFO half empty
4105 * 14 1=rx req on FIFO half full
4106 * 13 tx data IRQ enable
4107 * 12 tx idle IRQ enable
4108 * 11 rx break on IRQ enable
4109 * 10 rx data IRQ enable
4110 * 09 rx break off IRQ enable
4111 * 08 overrun IRQ enable
4112 * 07 DSR IRQ enable
4113 * 06 CTS IRQ enable
4114 * 05 DCD IRQ enable
4115 * 04 RI IRQ enable
4116 * 03 reserved, must be zero
4117 * 02 1=txd->rxd internal loopback enable
4118 * 01 reserved, must be zero
4119 * 00 1=master IRQ enable
4120 */
4121 val = BIT15 + BIT14 + BIT0;
4122 wr_reg16(info, SCR, val);
4123
4124 slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4125
4126 set_rate(info, info->params.data_rate * 16);
4127
4128 if (info->params.loopback)
4129 enable_loopback(info);
4130 }
4131
4132 static void sync_mode(struct slgt_info *info)
4133 {
4134 unsigned short val;
4135
4136 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4137 tx_stop(info);
4138 rx_stop(info);
4139
4140 /* TCR (tx control)
4141 *
4142 * 15..13 mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4143 * 12..10 encoding
4144 * 09 CRC enable
4145 * 08 CRC32
4146 * 07 1=RTS driver control
4147 * 06 preamble enable
4148 * 05..04 preamble length
4149 * 03 share open/close flag
4150 * 02 reset
4151 * 01 enable
4152 * 00 auto-CTS enable
4153 */
4154 val = BIT2;
4155
4156 switch(info->params.mode) {
4157 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4158 case MGSL_MODE_BISYNC: val |= BIT15; break;
4159 case MGSL_MODE_RAW: val |= BIT13; break;
4160 }
4161 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4162 val |= BIT7;
4163
4164 switch(info->params.encoding)
4165 {
4166 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4167 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4168 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4169 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4170 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4171 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4172 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4173 }
4174
4175 switch (info->params.crc_type & HDLC_CRC_MASK)
4176 {
4177 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4178 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4179 }
4180
4181 if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4182 val |= BIT6;
4183
4184 switch (info->params.preamble_length)
4185 {
4186 case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4187 case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4188 case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4189 }
4190
4191 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4192 val |= BIT0;
4193
4194 wr_reg16(info, TCR, val);
4195
4196 /* TPR (transmit preamble) */
4197
4198 switch (info->params.preamble)
4199 {
4200 case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4201 case HDLC_PREAMBLE_PATTERN_ONES: val = 0xff; break;
4202 case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4203 case HDLC_PREAMBLE_PATTERN_10: val = 0x55; break;
4204 case HDLC_PREAMBLE_PATTERN_01: val = 0xaa; break;
4205 default: val = 0x7e; break;
4206 }
4207 wr_reg8(info, TPR, (unsigned char)val);
4208
4209 /* RCR (rx control)
4210 *
4211 * 15..13 mode, 000=HDLC 001=raw 010=async 011=monosync 100=bisync
4212 * 12..10 encoding
4213 * 09 CRC enable
4214 * 08 CRC32
4215 * 07..03 reserved, must be 0
4216 * 02 reset
4217 * 01 enable
4218 * 00 auto-DCD enable
4219 */
4220 val = 0;
4221
4222 switch(info->params.mode) {
4223 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4224 case MGSL_MODE_BISYNC: val |= BIT15; break;
4225 case MGSL_MODE_RAW: val |= BIT13; break;
4226 }
4227
4228 switch(info->params.encoding)
4229 {
4230 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4231 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4232 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4233 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4234 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4235 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4236 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4237 }
4238
4239 switch (info->params.crc_type & HDLC_CRC_MASK)
4240 {
4241 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4242 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4243 }
4244
4245 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4246 val |= BIT0;
4247
4248 wr_reg16(info, RCR, val);
4249
4250 /* CCR (clock control)
4251 *
4252 * 07..05 tx clock source
4253 * 04..02 rx clock source
4254 * 01 auxclk enable
4255 * 00 BRG enable
4256 */
4257 val = 0;
4258
4259 if (info->params.flags & HDLC_FLAG_TXC_BRG)
4260 {
4261 // when RxC source is DPLL, BRG generates 16X DPLL
4262 // reference clock, so take TxC from BRG/16 to get
4263 // transmit clock at actual data rate
4264 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4265 val |= BIT6 + BIT5; /* 011, txclk = BRG/16 */
4266 else
4267 val |= BIT6; /* 010, txclk = BRG */
4268 }
4269 else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4270 val |= BIT7; /* 100, txclk = DPLL Input */
4271 else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4272 val |= BIT5; /* 001, txclk = RXC Input */
4273
4274 if (info->params.flags & HDLC_FLAG_RXC_BRG)
4275 val |= BIT3; /* 010, rxclk = BRG */
4276 else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4277 val |= BIT4; /* 100, rxclk = DPLL */
4278 else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4279 val |= BIT2; /* 001, rxclk = TXC Input */
4280
4281 if (info->params.clock_speed)
4282 val |= BIT1 + BIT0;
4283
4284 wr_reg8(info, CCR, (unsigned char)val);
4285
4286 if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4287 {
4288 // program DPLL mode
4289 switch(info->params.encoding)
4290 {
4291 case HDLC_ENCODING_BIPHASE_MARK:
4292 case HDLC_ENCODING_BIPHASE_SPACE:
4293 val = BIT7; break;
4294 case HDLC_ENCODING_BIPHASE_LEVEL:
4295 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4296 val = BIT7 + BIT6; break;
4297 default: val = BIT6; // NRZ encodings
4298 }
4299 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4300
4301 // DPLL requires a 16X reference clock from BRG
4302 set_rate(info, info->params.clock_speed * 16);
4303 }
4304 else
4305 set_rate(info, info->params.clock_speed);
4306
4307 tx_set_idle(info);
4308
4309 msc_set_vcr(info);
4310
4311 /* SCR (serial control)
4312 *
4313 * 15 1=tx req on FIFO half empty
4314 * 14 1=rx req on FIFO half full
4315 * 13 tx data IRQ enable
4316 * 12 tx idle IRQ enable
4317 * 11 underrun IRQ enable
4318 * 10 rx data IRQ enable
4319 * 09 rx idle IRQ enable
4320 * 08 overrun IRQ enable
4321 * 07 DSR IRQ enable
4322 * 06 CTS IRQ enable
4323 * 05 DCD IRQ enable
4324 * 04 RI IRQ enable
4325 * 03 reserved, must be zero
4326 * 02 1=txd->rxd internal loopback enable
4327 * 01 reserved, must be zero
4328 * 00 1=master IRQ enable
4329 */
4330 wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4331
4332 if (info->params.loopback)
4333 enable_loopback(info);
4334 }
4335
4336 /*
4337 * set transmit idle mode
4338 */
4339 static void tx_set_idle(struct slgt_info *info)
4340 {
4341 unsigned char val;
4342 unsigned short tcr;
4343
4344 /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4345 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4346 */
4347 tcr = rd_reg16(info, TCR);
4348 if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4349 /* disable preamble, set idle size to 16 bits */
4350 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4351 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4352 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4353 } else if (!(tcr & BIT6)) {
4354 /* preamble is disabled, set idle size to 8 bits */
4355 tcr &= ~(BIT5 + BIT4);
4356 }
4357 wr_reg16(info, TCR, tcr);
4358
4359 if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4360 /* LSB of custom tx idle specified in tx idle register */
4361 val = (unsigned char)(info->idle_mode & 0xff);
4362 } else {
4363 /* standard 8 bit idle patterns */
4364 switch(info->idle_mode)
4365 {
4366 case HDLC_TXIDLE_FLAGS: val = 0x7e; break;
4367 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4368 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4369 case HDLC_TXIDLE_ZEROS:
4370 case HDLC_TXIDLE_SPACE: val = 0x00; break;
4371 default: val = 0xff;
4372 }
4373 }
4374
4375 wr_reg8(info, TIR, val);
4376 }
4377
4378 /*
4379 * get state of V24 status (input) signals
4380 */
4381 static void get_signals(struct slgt_info *info)
4382 {
4383 unsigned short status = rd_reg16(info, SSR);
4384
4385 /* clear all serial signals except DTR and RTS */
4386 info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4387
4388 if (status & BIT3)
4389 info->signals |= SerialSignal_DSR;
4390 if (status & BIT2)
4391 info->signals |= SerialSignal_CTS;
4392 if (status & BIT1)
4393 info->signals |= SerialSignal_DCD;
4394 if (status & BIT0)
4395 info->signals |= SerialSignal_RI;
4396 }
4397
4398 /*
4399 * set V.24 Control Register based on current configuration
4400 */
4401 static void msc_set_vcr(struct slgt_info *info)
4402 {
4403 unsigned char val = 0;
4404
4405 /* VCR (V.24 control)
4406 *
4407 * 07..04 serial IF select
4408 * 03 DTR
4409 * 02 RTS
4410 * 01 LL
4411 * 00 RL
4412 */
4413
4414 switch(info->if_mode & MGSL_INTERFACE_MASK)
4415 {
4416 case MGSL_INTERFACE_RS232:
4417 val |= BIT5; /* 0010 */
4418 break;
4419 case MGSL_INTERFACE_V35:
4420 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4421 break;
4422 case MGSL_INTERFACE_RS422:
4423 val |= BIT6; /* 0100 */
4424 break;
4425 }
4426
4427 if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4428 val |= BIT4;
4429 if (info->signals & SerialSignal_DTR)
4430 val |= BIT3;
4431 if (info->signals & SerialSignal_RTS)
4432 val |= BIT2;
4433 if (info->if_mode & MGSL_INTERFACE_LL)
4434 val |= BIT1;
4435 if (info->if_mode & MGSL_INTERFACE_RL)
4436 val |= BIT0;
4437 wr_reg8(info, VCR, val);
4438 }
4439
4440 /*
4441 * set state of V24 control (output) signals
4442 */
4443 static void set_signals(struct slgt_info *info)
4444 {
4445 unsigned char val = rd_reg8(info, VCR);
4446 if (info->signals & SerialSignal_DTR)
4447 val |= BIT3;
4448 else
4449 val &= ~BIT3;
4450 if (info->signals & SerialSignal_RTS)
4451 val |= BIT2;
4452 else
4453 val &= ~BIT2;
4454 wr_reg8(info, VCR, val);
4455 }
4456
4457 /*
4458 * free range of receive DMA buffers (i to last)
4459 */
4460 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4461 {
4462 int done = 0;
4463
4464 while(!done) {
4465 /* reset current buffer for reuse */
4466 info->rbufs[i].status = 0;
4467 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4468 if (i == last)
4469 done = 1;
4470 if (++i == info->rbuf_count)
4471 i = 0;
4472 }
4473 info->rbuf_current = i;
4474 }
4475
4476 /*
4477 * mark all receive DMA buffers as free
4478 */
4479 static void reset_rbufs(struct slgt_info *info)
4480 {
4481 free_rbufs(info, 0, info->rbuf_count - 1);
4482 }
4483
4484 /*
4485 * pass receive HDLC frame to upper layer
4486 *
4487 * return true if frame available, otherwise false
4488 */
4489 static bool rx_get_frame(struct slgt_info *info)
4490 {
4491 unsigned int start, end;
4492 unsigned short status;
4493 unsigned int framesize = 0;
4494 unsigned long flags;
4495 struct tty_struct *tty = info->port.tty;
4496 unsigned char addr_field = 0xff;
4497 unsigned int crc_size = 0;
4498
4499 switch (info->params.crc_type & HDLC_CRC_MASK) {
4500 case HDLC_CRC_16_CCITT: crc_size = 2; break;
4501 case HDLC_CRC_32_CCITT: crc_size = 4; break;
4502 }
4503
4504 check_again:
4505
4506 framesize = 0;
4507 addr_field = 0xff;
4508 start = end = info->rbuf_current;
4509
4510 for (;;) {
4511 if (!desc_complete(info->rbufs[end]))
4512 goto cleanup;
4513
4514 if (framesize == 0 && info->params.addr_filter != 0xff)
4515 addr_field = info->rbufs[end].buf[0];
4516
4517 framesize += desc_count(info->rbufs[end]);
4518
4519 if (desc_eof(info->rbufs[end]))
4520 break;
4521
4522 if (++end == info->rbuf_count)
4523 end = 0;
4524
4525 if (end == info->rbuf_current) {
4526 if (info->rx_enabled){
4527 spin_lock_irqsave(&info->lock,flags);
4528 rx_start(info);
4529 spin_unlock_irqrestore(&info->lock,flags);
4530 }
4531 goto cleanup;
4532 }
4533 }
4534
4535 /* status
4536 *
4537 * 15 buffer complete
4538 * 14..06 reserved
4539 * 05..04 residue
4540 * 02 eof (end of frame)
4541 * 01 CRC error
4542 * 00 abort
4543 */
4544 status = desc_status(info->rbufs[end]);
4545
4546 /* ignore CRC bit if not using CRC (bit is undefined) */
4547 if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4548 status &= ~BIT1;
4549
4550 if (framesize == 0 ||
4551 (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4552 free_rbufs(info, start, end);
4553 goto check_again;
4554 }
4555
4556 if (framesize < (2 + crc_size) || status & BIT0) {
4557 info->icount.rxshort++;
4558 framesize = 0;
4559 } else if (status & BIT1) {
4560 info->icount.rxcrc++;
4561 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4562 framesize = 0;
4563 }
4564
4565 #if SYNCLINK_GENERIC_HDLC
4566 if (framesize == 0) {
4567 info->netdev->stats.rx_errors++;
4568 info->netdev->stats.rx_frame_errors++;
4569 }
4570 #endif
4571
4572 DBGBH(("%s rx frame status=%04X size=%d\n",
4573 info->device_name, status, framesize));
4574 DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4575
4576 if (framesize) {
4577 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4578 framesize -= crc_size;
4579 crc_size = 0;
4580 }
4581
4582 if (framesize > info->max_frame_size + crc_size)
4583 info->icount.rxlong++;
4584 else {
4585 /* copy dma buffer(s) to contiguous temp buffer */
4586 int copy_count = framesize;
4587 int i = start;
4588 unsigned char *p = info->tmp_rbuf;
4589 info->tmp_rbuf_count = framesize;
4590
4591 info->icount.rxok++;
4592
4593 while(copy_count) {
4594 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4595 memcpy(p, info->rbufs[i].buf, partial_count);
4596 p += partial_count;
4597 copy_count -= partial_count;
4598 if (++i == info->rbuf_count)
4599 i = 0;
4600 }
4601
4602 if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4603 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4604 framesize++;
4605 }
4606
4607 #if SYNCLINK_GENERIC_HDLC
4608 if (info->netcount)
4609 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4610 else
4611 #endif
4612 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4613 }
4614 }
4615 free_rbufs(info, start, end);
4616 return true;
4617
4618 cleanup:
4619 return false;
4620 }
4621
4622 /*
4623 * pass receive buffer (RAW synchronous mode) to tty layer
4624 * return true if buffer available, otherwise false
4625 */
4626 static bool rx_get_buf(struct slgt_info *info)
4627 {
4628 unsigned int i = info->rbuf_current;
4629 unsigned int count;
4630
4631 if (!desc_complete(info->rbufs[i]))
4632 return false;
4633 count = desc_count(info->rbufs[i]);
4634 switch(info->params.mode) {
4635 case MGSL_MODE_MONOSYNC:
4636 case MGSL_MODE_BISYNC:
4637 /* ignore residue in byte synchronous modes */
4638 if (desc_residue(info->rbufs[i]))
4639 count--;
4640 break;
4641 }
4642 DBGDATA(info, info->rbufs[i].buf, count, "rx");
4643 DBGINFO(("rx_get_buf size=%d\n", count));
4644 if (count)
4645 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4646 info->flag_buf, count);
4647 free_rbufs(info, i, i);
4648 return true;
4649 }
4650
4651 static void reset_tbufs(struct slgt_info *info)
4652 {
4653 unsigned int i;
4654 info->tbuf_current = 0;
4655 for (i=0 ; i < info->tbuf_count ; i++) {
4656 info->tbufs[i].status = 0;
4657 info->tbufs[i].count = 0;
4658 }
4659 }
4660
4661 /*
4662 * return number of free transmit DMA buffers
4663 */
4664 static unsigned int free_tbuf_count(struct slgt_info *info)
4665 {
4666 unsigned int count = 0;
4667 unsigned int i = info->tbuf_current;
4668
4669 do
4670 {
4671 if (desc_count(info->tbufs[i]))
4672 break; /* buffer in use */
4673 ++count;
4674 if (++i == info->tbuf_count)
4675 i=0;
4676 } while (i != info->tbuf_current);
4677
4678 /* if tx DMA active, last zero count buffer is in use */
4679 if (count && (rd_reg32(info, TDCSR) & BIT0))
4680 --count;
4681
4682 return count;
4683 }
4684
4685 /*
4686 * return number of bytes in unsent transmit DMA buffers
4687 * and the serial controller tx FIFO
4688 */
4689 static unsigned int tbuf_bytes(struct slgt_info *info)
4690 {
4691 unsigned int total_count = 0;
4692 unsigned int i = info->tbuf_current;
4693 unsigned int reg_value;
4694 unsigned int count;
4695 unsigned int active_buf_count = 0;
4696
4697 /*
4698 * Add descriptor counts for all tx DMA buffers.
4699 * If count is zero (cleared by DMA controller after read),
4700 * the buffer is complete or is actively being read from.
4701 *
4702 * Record buf_count of last buffer with zero count starting
4703 * from current ring position. buf_count is mirror
4704 * copy of count and is not cleared by serial controller.
4705 * If DMA controller is active, that buffer is actively
4706 * being read so add to total.
4707 */
4708 do {
4709 count = desc_count(info->tbufs[i]);
4710 if (count)
4711 total_count += count;
4712 else if (!total_count)
4713 active_buf_count = info->tbufs[i].buf_count;
4714 if (++i == info->tbuf_count)
4715 i = 0;
4716 } while (i != info->tbuf_current);
4717
4718 /* read tx DMA status register */
4719 reg_value = rd_reg32(info, TDCSR);
4720
4721 /* if tx DMA active, last zero count buffer is in use */
4722 if (reg_value & BIT0)
4723 total_count += active_buf_count;
4724
4725 /* add tx FIFO count = reg_value[15..8] */
4726 total_count += (reg_value >> 8) & 0xff;
4727
4728 /* if transmitter active add one byte for shift register */
4729 if (info->tx_active)
4730 total_count++;
4731
4732 return total_count;
4733 }
4734
4735 /*
4736 * load transmit DMA buffer(s) with data
4737 */
4738 static void tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4739 {
4740 unsigned short count;
4741 unsigned int i;
4742 struct slgt_desc *d;
4743
4744 if (size == 0)
4745 return;
4746
4747 DBGDATA(info, buf, size, "tx");
4748
4749 info->tbuf_start = i = info->tbuf_current;
4750
4751 while (size) {
4752 d = &info->tbufs[i];
4753 if (++i == info->tbuf_count)
4754 i = 0;
4755
4756 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4757 memcpy(d->buf, buf, count);
4758
4759 size -= count;
4760 buf += count;
4761
4762 /*
4763 * set EOF bit for last buffer of HDLC frame or
4764 * for every buffer in raw mode
4765 */
4766 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4767 info->params.mode == MGSL_MODE_RAW)
4768 set_desc_eof(*d, 1);
4769 else
4770 set_desc_eof(*d, 0);
4771
4772 set_desc_count(*d, count);
4773 d->buf_count = count;
4774 }
4775
4776 info->tbuf_current = i;
4777 }
4778
4779 static int register_test(struct slgt_info *info)
4780 {
4781 static unsigned short patterns[] =
4782 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4783 static unsigned int count = sizeof(patterns)/sizeof(patterns[0]);
4784 unsigned int i;
4785 int rc = 0;
4786
4787 for (i=0 ; i < count ; i++) {
4788 wr_reg16(info, TIR, patterns[i]);
4789 wr_reg16(info, BDR, patterns[(i+1)%count]);
4790 if ((rd_reg16(info, TIR) != patterns[i]) ||
4791 (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4792 rc = -ENODEV;
4793 break;
4794 }
4795 }
4796 info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4797 info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4798 return rc;
4799 }
4800
4801 static int irq_test(struct slgt_info *info)
4802 {
4803 unsigned long timeout;
4804 unsigned long flags;
4805 struct tty_struct *oldtty = info->port.tty;
4806 u32 speed = info->params.data_rate;
4807
4808 info->params.data_rate = 921600;
4809 info->port.tty = NULL;
4810
4811 spin_lock_irqsave(&info->lock, flags);
4812 async_mode(info);
4813 slgt_irq_on(info, IRQ_TXIDLE);
4814
4815 /* enable transmitter */
4816 wr_reg16(info, TCR,
4817 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4818
4819 /* write one byte and wait for tx idle */
4820 wr_reg16(info, TDR, 0);
4821
4822 /* assume failure */
4823 info->init_error = DiagStatus_IrqFailure;
4824 info->irq_occurred = false;
4825
4826 spin_unlock_irqrestore(&info->lock, flags);
4827
4828 timeout=100;
4829 while(timeout-- && !info->irq_occurred)
4830 msleep_interruptible(10);
4831
4832 spin_lock_irqsave(&info->lock,flags);
4833 reset_port(info);
4834 spin_unlock_irqrestore(&info->lock,flags);
4835
4836 info->params.data_rate = speed;
4837 info->port.tty = oldtty;
4838
4839 info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4840 return info->irq_occurred ? 0 : -ENODEV;
4841 }
4842
4843 static int loopback_test_rx(struct slgt_info *info)
4844 {
4845 unsigned char *src, *dest;
4846 int count;
4847
4848 if (desc_complete(info->rbufs[0])) {
4849 count = desc_count(info->rbufs[0]);
4850 src = info->rbufs[0].buf;
4851 dest = info->tmp_rbuf;
4852
4853 for( ; count ; count-=2, src+=2) {
4854 /* src=data byte (src+1)=status byte */
4855 if (!(*(src+1) & (BIT9 + BIT8))) {
4856 *dest = *src;
4857 dest++;
4858 info->tmp_rbuf_count++;
4859 }
4860 }
4861 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
4862 return 1;
4863 }
4864 return 0;
4865 }
4866
4867 static int loopback_test(struct slgt_info *info)
4868 {
4869 #define TESTFRAMESIZE 20
4870
4871 unsigned long timeout;
4872 u16 count = TESTFRAMESIZE;
4873 unsigned char buf[TESTFRAMESIZE];
4874 int rc = -ENODEV;
4875 unsigned long flags;
4876
4877 struct tty_struct *oldtty = info->port.tty;
4878 MGSL_PARAMS params;
4879
4880 memcpy(&params, &info->params, sizeof(params));
4881
4882 info->params.mode = MGSL_MODE_ASYNC;
4883 info->params.data_rate = 921600;
4884 info->params.loopback = 1;
4885 info->port.tty = NULL;
4886
4887 /* build and send transmit frame */
4888 for (count = 0; count < TESTFRAMESIZE; ++count)
4889 buf[count] = (unsigned char)count;
4890
4891 info->tmp_rbuf_count = 0;
4892 memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
4893
4894 /* program hardware for HDLC and enabled receiver */
4895 spin_lock_irqsave(&info->lock,flags);
4896 async_mode(info);
4897 rx_start(info);
4898 info->tx_count = count;
4899 tx_load(info, buf, count);
4900 tx_start(info);
4901 spin_unlock_irqrestore(&info->lock, flags);
4902
4903 /* wait for receive complete */
4904 for (timeout = 100; timeout; --timeout) {
4905 msleep_interruptible(10);
4906 if (loopback_test_rx(info)) {
4907 rc = 0;
4908 break;
4909 }
4910 }
4911
4912 /* verify received frame length and contents */
4913 if (!rc && (info->tmp_rbuf_count != count ||
4914 memcmp(buf, info->tmp_rbuf, count))) {
4915 rc = -ENODEV;
4916 }
4917
4918 spin_lock_irqsave(&info->lock,flags);
4919 reset_adapter(info);
4920 spin_unlock_irqrestore(&info->lock,flags);
4921
4922 memcpy(&info->params, &params, sizeof(info->params));
4923 info->port.tty = oldtty;
4924
4925 info->init_error = rc ? DiagStatus_DmaFailure : 0;
4926 return rc;
4927 }
4928
4929 static int adapter_test(struct slgt_info *info)
4930 {
4931 DBGINFO(("testing %s\n", info->device_name));
4932 if (register_test(info) < 0) {
4933 printk("register test failure %s addr=%08X\n",
4934 info->device_name, info->phys_reg_addr);
4935 } else if (irq_test(info) < 0) {
4936 printk("IRQ test failure %s IRQ=%d\n",
4937 info->device_name, info->irq_level);
4938 } else if (loopback_test(info) < 0) {
4939 printk("loopback test failure %s\n", info->device_name);
4940 }
4941 return info->init_error;
4942 }
4943
4944 /*
4945 * transmit timeout handler
4946 */
4947 static void tx_timeout(unsigned long context)
4948 {
4949 struct slgt_info *info = (struct slgt_info*)context;
4950 unsigned long flags;
4951
4952 DBGINFO(("%s tx_timeout\n", info->device_name));
4953 if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
4954 info->icount.txtimeout++;
4955 }
4956 spin_lock_irqsave(&info->lock,flags);
4957 info->tx_active = false;
4958 info->tx_count = 0;
4959 spin_unlock_irqrestore(&info->lock,flags);
4960
4961 #if SYNCLINK_GENERIC_HDLC
4962 if (info->netcount)
4963 hdlcdev_tx_done(info);
4964 else
4965 #endif
4966 bh_transmit(info);
4967 }
4968
4969 /*
4970 * receive buffer polling timer
4971 */
4972 static void rx_timeout(unsigned long context)
4973 {
4974 struct slgt_info *info = (struct slgt_info*)context;
4975 unsigned long flags;
4976
4977 DBGINFO(("%s rx_timeout\n", info->device_name));
4978 spin_lock_irqsave(&info->lock, flags);
4979 info->pending_bh |= BH_RECEIVE;
4980 spin_unlock_irqrestore(&info->lock, flags);
4981 bh_handler(&info->task);
4982 }
4983