arch/x86/platform/ce4100/ce4100.c

   1 /*
   2  * Intel CE4100  platform specific setup code
   3  *
   4  * (C) Copyright 2010 Intel Corporation
   5  *
   6  * This program is free software; you can redistribute it and/or
   7  * modify it under the terms of the GNU General Public License
   8  * as published by the Free Software Foundation; version 2
   9  * of the License.
  10  */
  11 #include <linux/init.h>
  12 #include <linux/kernel.h>
  13 #include <linux/irq.h>
  14 #include <linux/module.h>
  15 #include <linux/serial_reg.h>
  16 #include <linux/serial_8250.h>
  17
  18 #include <asm/ce4100.h>
  19 #include <asm/prom.h>
  20 #include <asm/setup.h>
  21 #include <asm/i8259.h>
  22 #include <asm/io.h>
  23 #include <asm/io_apic.h>
  24
  25 static int ce4100_i8042_detect(void)
  26 {
  27         return 0;
  28 }
  29
  30 #ifdef CONFIG_SERIAL_8250
  31
  32 static unsigned int mem_serial_in(struct uart_port *p, int offset)
  33 {
  34         offset = offset << p->regshift;
  35         return readl(p->membase + offset);
  36 }
  37
  38 /*
  39  * The UART Tx interrupts are not set under some conditions and therefore serial
  40  * transmission hangs. This is a silicon issue and has not been root caused. The
  41  * workaround for this silicon issue checks UART_LSR_THRE bit and UART_LSR_TEMT
  42  * bit of LSR register in interrupt handler to see whether at least one of these
  43  * two bits is set, if so then process the transmit request. If this workaround
  44  * is not applied, then the serial transmission may hang. This workaround is for
  45  * errata number 9 in Errata - B step.
  46 */
  47
  48 static unsigned int ce4100_mem_serial_in(struct uart_port *p, int offset)
  49 {
  50         unsigned int ret, ier, lsr;
  51
  52         if (offset == UART_IIR) {
  53                 offset = offset << p->regshift;
  54                 ret = readl(p->membase + offset);
  55                 if (ret & UART_IIR_NO_INT) {
  56                         /* see if the TX interrupt should have really set */
  57                         ier = mem_serial_in(p, UART_IER);
  58                         /* see if the UART's XMIT interrupt is enabled */
  59                         if (ier & UART_IER_THRI) {
  60                                 lsr = mem_serial_in(p, UART_LSR);
  61                                 /* now check to see if the UART should be
  62                                    generating an interrupt (but isn't) */
  63                                 if (lsr & (UART_LSR_THRE | UART_LSR_TEMT))
  64                                         ret &= ~UART_IIR_NO_INT;
  65                         }
  66                 }
  67         } else
  68                 ret =  mem_serial_in(p, offset);
  69         return ret;
  70 }
  71
  72 static void ce4100_mem_serial_out(struct uart_port *p, int offset, int value)
  73 {
  74         offset = offset << p->regshift;
  75         writel(value, p->membase + offset);
  76 }
  77
  78 static void ce4100_serial_fixup(int port, struct uart_port *up,
  79         unsigned short *capabilites)
  80 {
  81 #ifdef CONFIG_EARLY_PRINTK
  82         /*
  83          * Over ride the legacy port configuration that comes from
  84          * asm/serial.h. Using the ioport driver then switching to the
  85          * PCI memmaped driver hangs the IOAPIC
  86          */
  87         if (up->iotype !=  UPIO_MEM32) {
  88                 up->uartclk  = 14745600;
  89                 up->mapbase = 0xdffe0200;
  90                 set_fixmap_nocache(FIX_EARLYCON_MEM_BASE,
  91                                 up->mapbase & PAGE_MASK);
  92                 up->membase =
  93                         (void __iomem *)__fix_to_virt(FIX_EARLYCON_MEM_BASE);
  94                 up->membase += up->mapbase & ~PAGE_MASK;
  95                 up->iotype   = UPIO_MEM32;
  96                 up->regshift = 2;
  97         }
  98 #endif
  99         up->iobase = 0;
 100         up->serial_in = ce4100_mem_serial_in;
 101         up->serial_out = ce4100_mem_serial_out;
 102
 103         *capabilites |= (1 << 12);
 104 }
 105
 106 static __init void sdv_serial_fixup(void)
 107 {
 108         serial8250_set_isa_configurator(ce4100_serial_fixup);
 109 }
 110
 111 #else
 112 static inline void sdv_serial_fixup(void) {};
 113 #endif
 114
 115 static void __init sdv_arch_setup(void)
 116 {
 117         sdv_serial_fixup();
 118 }
 119
 120 #ifdef CONFIG_X86_IO_APIC
 121 static void __cpuinit sdv_pci_init(void)
 122 {
 123         x86_of_pci_init();
 124         /* We can't set this earlier, because we need to calibrate the timer */
 125         legacy_pic = &null_legacy_pic;
 126 }
 127 #endif
 128
 129 /*
 130  * CE4100 specific x86_init function overrides and early setup
 131  * calls.
 132  */
 133 void __init x86_ce4100_early_setup(void)
 134 {
 135         x86_init.oem.arch_setup = sdv_arch_setup;
 136         x86_platform.i8042_detect = ce4100_i8042_detect;
 137         x86_init.resources.probe_roms = x86_init_noop;
 138         x86_init.mpparse.get_smp_config = x86_init_uint_noop;
 139         x86_init.mpparse.find_smp_config = x86_init_noop;
 140         x86_init.pci.init = ce4100_pci_init;
 141
 142 #ifdef CONFIG_X86_IO_APIC
 143         x86_init.pci.init_irq = sdv_pci_init;
 144         x86_init.mpparse.setup_ioapic_ids = setup_ioapic_ids_from_mpc_nocheck;
 145 #endif
 146 }