Blackfin: mass clean up of copyright/licensing info
[GitHub/mt8127/android_kernel_alcatel_ttab.git] / arch / blackfin / mach-bf537 / boards / cm_bf537u.c
1 /*
2 * Copyright 2004-2009 Analog Devices Inc.
3 * 2008-2009 Bluetechnix
4 * 2005 National ICT Australia (NICTA)
5 * Aidan Williams <aidan@nicta.com.au>
6 *
7 * Licensed under the GPL-2 or later.
8 */
9
10 #include <linux/device.h>
11 #include <linux/etherdevice.h>
12 #include <linux/platform_device.h>
13 #include <linux/mtd/mtd.h>
14 #include <linux/mtd/partitions.h>
15 #include <linux/mtd/physmap.h>
16 #include <linux/spi/spi.h>
17 #include <linux/spi/flash.h>
18 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
19 #include <linux/usb/isp1362.h>
20 #endif
21 #include <linux/ata_platform.h>
22 #include <linux/irq.h>
23 #include <asm/dma.h>
24 #include <asm/bfin5xx_spi.h>
25 #include <asm/portmux.h>
26 #include <asm/dpmc.h>
27 #include <linux/spi/mmc_spi.h>
28
29 /*
30 * Name the Board for the /proc/cpuinfo
31 */
32 const char bfin_board_name[] = "Bluetechnix CM BF537U";
33
34 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
35 /* all SPI peripherals info goes here */
36
37 #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
38 static struct mtd_partition bfin_spi_flash_partitions[] = {
39 {
40 .name = "bootloader(spi)",
41 .size = 0x00020000,
42 .offset = 0,
43 .mask_flags = MTD_CAP_ROM
44 }, {
45 .name = "linux kernel(spi)",
46 .size = 0xe0000,
47 .offset = 0x20000
48 }, {
49 .name = "file system(spi)",
50 .size = 0x700000,
51 .offset = 0x00100000,
52 }
53 };
54
55 static struct flash_platform_data bfin_spi_flash_data = {
56 .name = "m25p80",
57 .parts = bfin_spi_flash_partitions,
58 .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
59 .type = "m25p64",
60 };
61
62 /* SPI flash chip (m25p64) */
63 static struct bfin5xx_spi_chip spi_flash_chip_info = {
64 .enable_dma = 0, /* use dma transfer with this chip*/
65 .bits_per_word = 8,
66 };
67 #endif
68
69 #if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
70 /* SPI ADC chip */
71 static struct bfin5xx_spi_chip spi_adc_chip_info = {
72 .enable_dma = 1, /* use dma transfer with this chip*/
73 .bits_per_word = 16,
74 };
75 #endif
76
77 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
78 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
79 .enable_dma = 0,
80 .bits_per_word = 16,
81 };
82 #endif
83
84 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
85 static struct bfin5xx_spi_chip mmc_spi_chip_info = {
86 .enable_dma = 0,
87 .bits_per_word = 8,
88 };
89 #endif
90
91 static struct spi_board_info bfin_spi_board_info[] __initdata = {
92 #if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
93 {
94 /* the modalias must be the same as spi device driver name */
95 .modalias = "m25p80", /* Name of spi_driver for this device */
96 .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
97 .bus_num = 0, /* Framework bus number */
98 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
99 .platform_data = &bfin_spi_flash_data,
100 .controller_data = &spi_flash_chip_info,
101 .mode = SPI_MODE_3,
102 },
103 #endif
104
105 #if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
106 {
107 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
108 .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
109 .bus_num = 0, /* Framework bus number */
110 .chip_select = 1, /* Framework chip select. */
111 .platform_data = NULL, /* No spi_driver specific config */
112 .controller_data = &spi_adc_chip_info,
113 },
114 #endif
115
116 #if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
117 {
118 .modalias = "ad1836",
119 .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
120 .bus_num = 0,
121 .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
122 .controller_data = &ad1836_spi_chip_info,
123 },
124 #endif
125
126 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
127 {
128 .modalias = "mmc_spi",
129 .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
130 .bus_num = 0,
131 .chip_select = 1,
132 .controller_data = &mmc_spi_chip_info,
133 .mode = SPI_MODE_3,
134 },
135 #endif
136 };
137
138 /* SPI (0) */
139 static struct resource bfin_spi0_resource[] = {
140 [0] = {
141 .start = SPI0_REGBASE,
142 .end = SPI0_REGBASE + 0xFF,
143 .flags = IORESOURCE_MEM,
144 },
145 [1] = {
146 .start = CH_SPI,
147 .end = CH_SPI,
148 .flags = IORESOURCE_DMA,
149 },
150 [2] = {
151 .start = IRQ_SPI,
152 .end = IRQ_SPI,
153 .flags = IORESOURCE_IRQ,
154 },
155 };
156
157 /* SPI controller data */
158 static struct bfin5xx_spi_master bfin_spi0_info = {
159 .num_chipselect = 8,
160 .enable_dma = 1, /* master has the ability to do dma transfer */
161 .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
162 };
163
164 static struct platform_device bfin_spi0_device = {
165 .name = "bfin-spi",
166 .id = 0, /* Bus number */
167 .num_resources = ARRAY_SIZE(bfin_spi0_resource),
168 .resource = bfin_spi0_resource,
169 .dev = {
170 .platform_data = &bfin_spi0_info, /* Passed to driver */
171 },
172 };
173 #endif /* spi master and devices */
174
175 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
176 static struct platform_device rtc_device = {
177 .name = "rtc-bfin",
178 .id = -1,
179 };
180 #endif
181
182 #if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
183 static struct platform_device hitachi_fb_device = {
184 .name = "hitachi-tx09",
185 };
186 #endif
187
188 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
189 #include <linux/smc91x.h>
190
191 static struct smc91x_platdata smc91x_info = {
192 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
193 .leda = RPC_LED_100_10,
194 .ledb = RPC_LED_TX_RX,
195 };
196
197 static struct resource smc91x_resources[] = {
198 {
199 .start = 0x20200300,
200 .end = 0x20200300 + 16,
201 .flags = IORESOURCE_MEM,
202 }, {
203 .start = IRQ_PF14,
204 .end = IRQ_PF14,
205 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
206 },
207 };
208
209 static struct platform_device smc91x_device = {
210 .name = "smc91x",
211 .id = 0,
212 .num_resources = ARRAY_SIZE(smc91x_resources),
213 .resource = smc91x_resources,
214 .dev = {
215 .platform_data = &smc91x_info,
216 },
217 };
218 #endif
219
220 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
221 static struct resource isp1362_hcd_resources[] = {
222 {
223 .start = 0x20308000,
224 .end = 0x20308000,
225 .flags = IORESOURCE_MEM,
226 }, {
227 .start = 0x20308004,
228 .end = 0x20308004,
229 .flags = IORESOURCE_MEM,
230 }, {
231 .start = IRQ_PG15,
232 .end = IRQ_PG15,
233 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
234 },
235 };
236
237 static struct isp1362_platform_data isp1362_priv = {
238 .sel15Kres = 1,
239 .clknotstop = 0,
240 .oc_enable = 0,
241 .int_act_high = 0,
242 .int_edge_triggered = 0,
243 .remote_wakeup_connected = 0,
244 .no_power_switching = 1,
245 .power_switching_mode = 0,
246 };
247
248 static struct platform_device isp1362_hcd_device = {
249 .name = "isp1362-hcd",
250 .id = 0,
251 .dev = {
252 .platform_data = &isp1362_priv,
253 },
254 .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
255 .resource = isp1362_hcd_resources,
256 };
257 #endif
258
259 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
260 static struct resource net2272_bfin_resources[] = {
261 {
262 .start = 0x20200000,
263 .end = 0x20200000 + 0x100,
264 .flags = IORESOURCE_MEM,
265 }, {
266 .start = IRQ_PH14,
267 .end = IRQ_PH14,
268 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
269 },
270 };
271
272 static struct platform_device net2272_bfin_device = {
273 .name = "net2272",
274 .id = -1,
275 .num_resources = ARRAY_SIZE(net2272_bfin_resources),
276 .resource = net2272_bfin_resources,
277 };
278 #endif
279
280 static struct resource bfin_gpios_resources = {
281 .start = 0,
282 .end = MAX_BLACKFIN_GPIOS - 1,
283 .flags = IORESOURCE_IRQ,
284 };
285
286 static struct platform_device bfin_gpios_device = {
287 .name = "simple-gpio",
288 .id = -1,
289 .num_resources = 1,
290 .resource = &bfin_gpios_resources,
291 };
292
293 #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
294 static struct mtd_partition cm_partitions[] = {
295 {
296 .name = "bootloader(nor)",
297 .size = 0x40000,
298 .offset = 0,
299 }, {
300 .name = "linux kernel(nor)",
301 .size = 0x100000,
302 .offset = MTDPART_OFS_APPEND,
303 }, {
304 .name = "file system(nor)",
305 .size = MTDPART_SIZ_FULL,
306 .offset = MTDPART_OFS_APPEND,
307 }
308 };
309
310 static struct physmap_flash_data cm_flash_data = {
311 .width = 2,
312 .parts = cm_partitions,
313 .nr_parts = ARRAY_SIZE(cm_partitions),
314 };
315
316 static unsigned cm_flash_gpios[] = { GPIO_PH0 };
317
318 static struct resource cm_flash_resource[] = {
319 {
320 .name = "cfi_probe",
321 .start = 0x20000000,
322 .end = 0x201fffff,
323 .flags = IORESOURCE_MEM,
324 }, {
325 .start = (unsigned long)cm_flash_gpios,
326 .end = ARRAY_SIZE(cm_flash_gpios),
327 .flags = IORESOURCE_IRQ,
328 }
329 };
330
331 static struct platform_device cm_flash_device = {
332 .name = "gpio-addr-flash",
333 .id = 0,
334 .dev = {
335 .platform_data = &cm_flash_data,
336 },
337 .num_resources = ARRAY_SIZE(cm_flash_resource),
338 .resource = cm_flash_resource,
339 };
340 #endif
341
342 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
343 static struct resource bfin_uart_resources[] = {
344 {
345 .start = 0xFFC00400,
346 .end = 0xFFC004FF,
347 .flags = IORESOURCE_MEM,
348 }, {
349 .start = 0xFFC02000,
350 .end = 0xFFC020FF,
351 .flags = IORESOURCE_MEM,
352 },
353 };
354
355 static struct platform_device bfin_uart_device = {
356 .name = "bfin-uart",
357 .id = 1,
358 .num_resources = ARRAY_SIZE(bfin_uart_resources),
359 .resource = bfin_uart_resources,
360 };
361 #endif
362
363 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
364 #ifdef CONFIG_BFIN_SIR0
365 static struct resource bfin_sir0_resources[] = {
366 {
367 .start = 0xFFC00400,
368 .end = 0xFFC004FF,
369 .flags = IORESOURCE_MEM,
370 },
371 {
372 .start = IRQ_UART0_RX,
373 .end = IRQ_UART0_RX+1,
374 .flags = IORESOURCE_IRQ,
375 },
376 {
377 .start = CH_UART0_RX,
378 .end = CH_UART0_RX+1,
379 .flags = IORESOURCE_DMA,
380 },
381 };
382 static struct platform_device bfin_sir0_device = {
383 .name = "bfin_sir",
384 .id = 0,
385 .num_resources = ARRAY_SIZE(bfin_sir0_resources),
386 .resource = bfin_sir0_resources,
387 };
388 #endif
389 #ifdef CONFIG_BFIN_SIR1
390 static struct resource bfin_sir1_resources[] = {
391 {
392 .start = 0xFFC02000,
393 .end = 0xFFC020FF,
394 .flags = IORESOURCE_MEM,
395 },
396 {
397 .start = IRQ_UART1_RX,
398 .end = IRQ_UART1_RX+1,
399 .flags = IORESOURCE_IRQ,
400 },
401 {
402 .start = CH_UART1_RX,
403 .end = CH_UART1_RX+1,
404 .flags = IORESOURCE_DMA,
405 },
406 };
407 static struct platform_device bfin_sir1_device = {
408 .name = "bfin_sir",
409 .id = 1,
410 .num_resources = ARRAY_SIZE(bfin_sir1_resources),
411 .resource = bfin_sir1_resources,
412 };
413 #endif
414 #endif
415
416 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
417 static struct resource bfin_twi0_resource[] = {
418 [0] = {
419 .start = TWI0_REGBASE,
420 .end = TWI0_REGBASE,
421 .flags = IORESOURCE_MEM,
422 },
423 [1] = {
424 .start = IRQ_TWI,
425 .end = IRQ_TWI,
426 .flags = IORESOURCE_IRQ,
427 },
428 };
429
430 static struct platform_device i2c_bfin_twi_device = {
431 .name = "i2c-bfin-twi",
432 .id = 0,
433 .num_resources = ARRAY_SIZE(bfin_twi0_resource),
434 .resource = bfin_twi0_resource,
435 };
436 #endif
437
438 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
439 static struct platform_device bfin_sport0_uart_device = {
440 .name = "bfin-sport-uart",
441 .id = 0,
442 };
443
444 static struct platform_device bfin_sport1_uart_device = {
445 .name = "bfin-sport-uart",
446 .id = 1,
447 };
448 #endif
449
450 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
451 static struct platform_device bfin_mii_bus = {
452 .name = "bfin_mii_bus",
453 };
454
455 static struct platform_device bfin_mac_device = {
456 .name = "bfin_mac",
457 .dev.platform_data = &bfin_mii_bus,
458 };
459 #endif
460
461 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
462 #define PATA_INT IRQ_PF14
463
464 static struct pata_platform_info bfin_pata_platform_data = {
465 .ioport_shift = 2,
466 .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
467 };
468
469 static struct resource bfin_pata_resources[] = {
470 {
471 .start = 0x2030C000,
472 .end = 0x2030C01F,
473 .flags = IORESOURCE_MEM,
474 },
475 {
476 .start = 0x2030D018,
477 .end = 0x2030D01B,
478 .flags = IORESOURCE_MEM,
479 },
480 {
481 .start = PATA_INT,
482 .end = PATA_INT,
483 .flags = IORESOURCE_IRQ,
484 },
485 };
486
487 static struct platform_device bfin_pata_device = {
488 .name = "pata_platform",
489 .id = -1,
490 .num_resources = ARRAY_SIZE(bfin_pata_resources),
491 .resource = bfin_pata_resources,
492 .dev = {
493 .platform_data = &bfin_pata_platform_data,
494 }
495 };
496 #endif
497
498 static const unsigned int cclk_vlev_datasheet[] =
499 {
500 VRPAIR(VLEV_085, 250000000),
501 VRPAIR(VLEV_090, 376000000),
502 VRPAIR(VLEV_095, 426000000),
503 VRPAIR(VLEV_100, 426000000),
504 VRPAIR(VLEV_105, 476000000),
505 VRPAIR(VLEV_110, 476000000),
506 VRPAIR(VLEV_115, 476000000),
507 VRPAIR(VLEV_120, 500000000),
508 VRPAIR(VLEV_125, 533000000),
509 VRPAIR(VLEV_130, 600000000),
510 };
511
512 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
513 .tuple_tab = cclk_vlev_datasheet,
514 .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
515 .vr_settling_time = 25 /* us */,
516 };
517
518 static struct platform_device bfin_dpmc = {
519 .name = "bfin dpmc",
520 .dev = {
521 .platform_data = &bfin_dmpc_vreg_data,
522 },
523 };
524
525 static struct platform_device *cm_bf537u_devices[] __initdata = {
526
527 &bfin_dpmc,
528
529 #if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
530 &hitachi_fb_device,
531 #endif
532
533 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
534 &rtc_device,
535 #endif
536
537 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
538 &bfin_uart_device,
539 #endif
540
541 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
542 #ifdef CONFIG_BFIN_SIR0
543 &bfin_sir0_device,
544 #endif
545 #ifdef CONFIG_BFIN_SIR1
546 &bfin_sir1_device,
547 #endif
548 #endif
549
550 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
551 &i2c_bfin_twi_device,
552 #endif
553
554 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
555 &bfin_sport0_uart_device,
556 &bfin_sport1_uart_device,
557 #endif
558
559 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
560 &isp1362_hcd_device,
561 #endif
562
563 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
564 &smc91x_device,
565 #endif
566
567 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
568 &bfin_mii_bus,
569 &bfin_mac_device,
570 #endif
571
572 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
573 &net2272_bfin_device,
574 #endif
575
576 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
577 &bfin_spi0_device,
578 #endif
579
580 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
581 &bfin_pata_device,
582 #endif
583
584 #if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
585 &cm_flash_device,
586 #endif
587
588 &bfin_gpios_device,
589 };
590
591 static int __init cm_bf537u_init(void)
592 {
593 printk(KERN_INFO "%s(): registering device resources\n", __func__);
594 platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
595 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
596 spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
597 #endif
598
599 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
600 irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
601 #endif
602 return 0;
603 }
604
605 arch_initcall(cm_bf537u_init);
606
607 void bfin_get_ether_addr(char *addr)
608 {
609 random_ether_addr(addr);
610 printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
611 }
612 EXPORT_SYMBOL(bfin_get_ether_addr);