| 1 | /* |
| 2 | * Atmel MultiMedia Card Interface driver |
| 3 | * |
| 4 | * Copyright (C) 2004-2006 Atmel Corporation |
| 5 | * |
| 6 | * This program is free software; you can redistribute it and/or modify |
| 7 | * it under the terms of the GNU General Public License version 2 as |
| 8 | * published by the Free Software Foundation. |
| 9 | */ |
| 10 | |
| 11 | /* |
| 12 | * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors |
| 13 | * Registers and bitfields marked with [2] are only available in MCI2 |
| 14 | */ |
| 15 | |
| 16 | #ifndef __DRIVERS_MMC_ATMEL_MCI_H__ |
| 17 | #define __DRIVERS_MMC_ATMEL_MCI_H__ |
| 18 | |
| 19 | /* MCI Register Definitions */ |
| 20 | #define ATMCI_CR 0x0000 /* Control */ |
| 21 | # define ATMCI_CR_MCIEN ( 1 << 0) /* MCI Enable */ |
| 22 | # define ATMCI_CR_MCIDIS ( 1 << 1) /* MCI Disable */ |
| 23 | # define ATMCI_CR_PWSEN ( 1 << 2) /* Power Save Enable */ |
| 24 | # define ATMCI_CR_PWSDIS ( 1 << 3) /* Power Save Disable */ |
| 25 | # define ATMCI_CR_SWRST ( 1 << 7) /* Software Reset */ |
| 26 | #define ATMCI_MR 0x0004 /* Mode */ |
| 27 | # define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */ |
| 28 | # define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */ |
| 29 | # define ATMCI_MR_RDPROOF ( 1 << 11) /* Read Proof */ |
| 30 | # define ATMCI_MR_WRPROOF ( 1 << 12) /* Write Proof */ |
| 31 | # define ATMCI_MR_PDCFBYTE ( 1 << 13) /* Force Byte Transfer */ |
| 32 | # define ATMCI_MR_PDCPADV ( 1 << 14) /* Padding Value */ |
| 33 | # define ATMCI_MR_PDCMODE ( 1 << 15) /* PDC-oriented Mode */ |
| 34 | #define ATMCI_DTOR 0x0008 /* Data Timeout */ |
| 35 | # define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */ |
| 36 | # define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */ |
| 37 | #define ATMCI_SDCR 0x000c /* SD Card / SDIO */ |
| 38 | # define ATMCI_SDCSEL_SLOT_A ( 0 << 0) /* Select SD slot A */ |
| 39 | # define ATMCI_SDCSEL_SLOT_B ( 1 << 0) /* Select SD slot A */ |
| 40 | # define ATMCI_SDCSEL_MASK ( 3 << 0) |
| 41 | # define ATMCI_SDCBUS_1BIT ( 0 << 6) /* 1-bit data bus */ |
| 42 | # define ATMCI_SDCBUS_4BIT ( 2 << 6) /* 4-bit data bus */ |
| 43 | # define ATMCI_SDCBUS_8BIT ( 3 << 6) /* 8-bit data bus[2] */ |
| 44 | # define ATMCI_SDCBUS_MASK ( 3 << 6) |
| 45 | #define ATMCI_ARGR 0x0010 /* Command Argument */ |
| 46 | #define ATMCI_CMDR 0x0014 /* Command */ |
| 47 | # define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */ |
| 48 | # define ATMCI_CMDR_RSPTYP_NONE ( 0 << 6) /* No response */ |
| 49 | # define ATMCI_CMDR_RSPTYP_48BIT ( 1 << 6) /* 48-bit response */ |
| 50 | # define ATMCI_CMDR_RSPTYP_136BIT ( 2 << 6) /* 136-bit response */ |
| 51 | # define ATMCI_CMDR_SPCMD_INIT ( 1 << 8) /* Initialization command */ |
| 52 | # define ATMCI_CMDR_SPCMD_SYNC ( 2 << 8) /* Synchronized command */ |
| 53 | # define ATMCI_CMDR_SPCMD_INT ( 4 << 8) /* Interrupt command */ |
| 54 | # define ATMCI_CMDR_SPCMD_INTRESP ( 5 << 8) /* Interrupt response */ |
| 55 | # define ATMCI_CMDR_OPDCMD ( 1 << 11) /* Open Drain */ |
| 56 | # define ATMCI_CMDR_MAXLAT_5CYC ( 0 << 12) /* Max latency 5 cycles */ |
| 57 | # define ATMCI_CMDR_MAXLAT_64CYC ( 1 << 12) /* Max latency 64 cycles */ |
| 58 | # define ATMCI_CMDR_START_XFER ( 1 << 16) /* Start data transfer */ |
| 59 | # define ATMCI_CMDR_STOP_XFER ( 2 << 16) /* Stop data transfer */ |
| 60 | # define ATMCI_CMDR_TRDIR_WRITE ( 0 << 18) /* Write data */ |
| 61 | # define ATMCI_CMDR_TRDIR_READ ( 1 << 18) /* Read data */ |
| 62 | # define ATMCI_CMDR_BLOCK ( 0 << 19) /* Single-block transfer */ |
| 63 | # define ATMCI_CMDR_MULTI_BLOCK ( 1 << 19) /* Multi-block transfer */ |
| 64 | # define ATMCI_CMDR_STREAM ( 2 << 19) /* MMC Stream transfer */ |
| 65 | # define ATMCI_CMDR_SDIO_BYTE ( 4 << 19) /* SDIO Byte transfer */ |
| 66 | # define ATMCI_CMDR_SDIO_BLOCK ( 5 << 19) /* SDIO Block transfer */ |
| 67 | # define ATMCI_CMDR_SDIO_SUSPEND ( 1 << 24) /* SDIO Suspend Command */ |
| 68 | # define ATMCI_CMDR_SDIO_RESUME ( 2 << 24) /* SDIO Resume Command */ |
| 69 | #define ATMCI_BLKR 0x0018 /* Block */ |
| 70 | # define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */ |
| 71 | # define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */ |
| 72 | #define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */ |
| 73 | # define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */ |
| 74 | # define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */ |
| 75 | #define ATMCI_RSPR 0x0020 /* Response 0 */ |
| 76 | #define ATMCI_RSPR1 0x0024 /* Response 1 */ |
| 77 | #define ATMCI_RSPR2 0x0028 /* Response 2 */ |
| 78 | #define ATMCI_RSPR3 0x002c /* Response 3 */ |
| 79 | #define ATMCI_RDR 0x0030 /* Receive Data */ |
| 80 | #define ATMCI_TDR 0x0034 /* Transmit Data */ |
| 81 | #define ATMCI_SR 0x0040 /* Status */ |
| 82 | #define ATMCI_IER 0x0044 /* Interrupt Enable */ |
| 83 | #define ATMCI_IDR 0x0048 /* Interrupt Disable */ |
| 84 | #define ATMCI_IMR 0x004c /* Interrupt Mask */ |
| 85 | # define ATMCI_CMDRDY ( 1 << 0) /* Command Ready */ |
| 86 | # define ATMCI_RXRDY ( 1 << 1) /* Receiver Ready */ |
| 87 | # define ATMCI_TXRDY ( 1 << 2) /* Transmitter Ready */ |
| 88 | # define ATMCI_BLKE ( 1 << 3) /* Data Block Ended */ |
| 89 | # define ATMCI_DTIP ( 1 << 4) /* Data Transfer In Progress */ |
| 90 | # define ATMCI_NOTBUSY ( 1 << 5) /* Data Not Busy */ |
| 91 | # define ATMCI_ENDRX ( 1 << 6) /* End of RX Buffer */ |
| 92 | # define ATMCI_ENDTX ( 1 << 7) /* End of TX Buffer */ |
| 93 | # define ATMCI_SDIOIRQA ( 1 << 8) /* SDIO IRQ in slot A */ |
| 94 | # define ATMCI_SDIOIRQB ( 1 << 9) /* SDIO IRQ in slot B */ |
| 95 | # define ATMCI_SDIOWAIT ( 1 << 12) /* SDIO Read Wait Operation Status */ |
| 96 | # define ATMCI_CSRCV ( 1 << 13) /* CE-ATA Completion Signal Received */ |
| 97 | # define ATMCI_RXBUFF ( 1 << 14) /* RX Buffer Full */ |
| 98 | # define ATMCI_TXBUFE ( 1 << 15) /* TX Buffer Empty */ |
| 99 | # define ATMCI_RINDE ( 1 << 16) /* Response Index Error */ |
| 100 | # define ATMCI_RDIRE ( 1 << 17) /* Response Direction Error */ |
| 101 | # define ATMCI_RCRCE ( 1 << 18) /* Response CRC Error */ |
| 102 | # define ATMCI_RENDE ( 1 << 19) /* Response End Bit Error */ |
| 103 | # define ATMCI_RTOE ( 1 << 20) /* Response Time-Out Error */ |
| 104 | # define ATMCI_DCRCE ( 1 << 21) /* Data CRC Error */ |
| 105 | # define ATMCI_DTOE ( 1 << 22) /* Data Time-Out Error */ |
| 106 | # define ATMCI_CSTOE ( 1 << 23) /* Completion Signal Time-out Error */ |
| 107 | # define ATMCI_BLKOVRE ( 1 << 24) /* DMA Block Overrun Error */ |
| 108 | # define ATMCI_DMADONE ( 1 << 25) /* DMA Transfer Done */ |
| 109 | # define ATMCI_FIFOEMPTY ( 1 << 26) /* FIFO Empty Flag */ |
| 110 | # define ATMCI_XFRDONE ( 1 << 27) /* Transfer Done Flag */ |
| 111 | # define ATMCI_ACKRCV ( 1 << 28) /* Boot Operation Acknowledge Received */ |
| 112 | # define ATMCI_ACKRCVE ( 1 << 29) /* Boot Operation Acknowledge Error */ |
| 113 | # define ATMCI_OVRE ( 1 << 30) /* RX Overrun Error */ |
| 114 | # define ATMCI_UNRE ( 1 << 31) /* TX Underrun Error */ |
| 115 | #define ATMCI_DMA 0x0050 /* DMA Configuration[2] */ |
| 116 | # define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */ |
| 117 | # define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */ |
| 118 | # define ATMCI_DMAEN ( 1 << 8) /* DMA Hardware Handshaking Enable */ |
| 119 | #define ATMCI_CFG 0x0054 /* Configuration[2] */ |
| 120 | # define ATMCI_CFG_FIFOMODE_1DATA ( 1 << 0) /* MCI Internal FIFO control mode */ |
| 121 | # define ATMCI_CFG_FERRCTRL_COR ( 1 << 4) /* Flow Error flag reset control mode */ |
| 122 | # define ATMCI_CFG_HSMODE ( 1 << 8) /* High Speed Mode */ |
| 123 | # define ATMCI_CFG_LSYNC ( 1 << 12) /* Synchronize on the last block */ |
| 124 | #define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */ |
| 125 | # define ATMCI_WP_EN ( 1 << 0) /* WP Enable */ |
| 126 | # define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */ |
| 127 | #define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */ |
| 128 | # define ATMCI_GET_WP_VS(x) ((x) & 0x0f) |
| 129 | # define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff) |
| 130 | #define ATMCI_VERSION 0x00FC /* Version */ |
| 131 | #define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */ |
| 132 | |
| 133 | /* This is not including the FIFO Aperture on MCI2 */ |
| 134 | #define ATMCI_REGS_SIZE 0x100 |
| 135 | |
| 136 | /* Register access macros */ |
| 137 | #define atmci_readl(port,reg) \ |
| 138 | __raw_readl((port)->regs + reg) |
| 139 | #define atmci_writel(port,reg,value) \ |
| 140 | __raw_writel((value), (port)->regs + reg) |
| 141 | |
| 142 | #endif /* __DRIVERS_MMC_ATMEL_MCI_H__ */ |