| 1 | Kernel driver ltc4245 |
| 2 | ===================== |
| 3 | |
| 4 | Supported chips: |
| 5 | * Linear Technology LTC4245 |
| 6 | Prefix: 'ltc4245' |
| 7 | Addresses scanned: 0x20-0x3f |
| 8 | Datasheet: |
| 9 | http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517 |
| 10 | |
| 11 | Author: Ira W. Snyder <iws@ovro.caltech.edu> |
| 12 | |
| 13 | |
| 14 | Description |
| 15 | ----------- |
| 16 | |
| 17 | The LTC4245 controller allows a board to be safely inserted and removed |
| 18 | from a live backplane in multiple supply systems such as CompactPCI and |
| 19 | PCI Express. |
| 20 | |
| 21 | |
| 22 | Usage Notes |
| 23 | ----------- |
| 24 | |
| 25 | This driver does not probe for LTC4245 devices, due to the fact that some |
| 26 | of the possible addresses are unfriendly to probing. You will have to |
| 27 | instantiate the devices explicitly. |
| 28 | |
| 29 | Example: the following will load the driver for an LTC4245 at address 0x23 |
| 30 | on I2C bus #1: |
| 31 | $ modprobe ltc4245 |
| 32 | $ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device |
| 33 | |
| 34 | |
| 35 | Sysfs entries |
| 36 | ------------- |
| 37 | |
| 38 | The LTC4245 has built-in limits for over and under current warnings. This |
| 39 | makes it very likely that the reference circuit will be used. |
| 40 | |
| 41 | This driver uses the values in the datasheet to change the register values |
| 42 | into the values specified in the sysfs-interface document. The current readings |
| 43 | rely on the sense resistors listed in Table 2: "Sense Resistor Values". |
| 44 | |
| 45 | in1_input 12v input voltage (mV) |
| 46 | in2_input 5v input voltage (mV) |
| 47 | in3_input 3v input voltage (mV) |
| 48 | in4_input Vee (-12v) input voltage (mV) |
| 49 | |
| 50 | in1_min_alarm 12v input undervoltage alarm |
| 51 | in2_min_alarm 5v input undervoltage alarm |
| 52 | in3_min_alarm 3v input undervoltage alarm |
| 53 | in4_min_alarm Vee (-12v) input undervoltage alarm |
| 54 | |
| 55 | curr1_input 12v current (mA) |
| 56 | curr2_input 5v current (mA) |
| 57 | curr3_input 3v current (mA) |
| 58 | curr4_input Vee (-12v) current (mA) |
| 59 | |
| 60 | curr1_max_alarm 12v overcurrent alarm |
| 61 | curr2_max_alarm 5v overcurrent alarm |
| 62 | curr3_max_alarm 3v overcurrent alarm |
| 63 | curr4_max_alarm Vee (-12v) overcurrent alarm |
| 64 | |
| 65 | in5_input 12v output voltage (mV) |
| 66 | in6_input 5v output voltage (mV) |
| 67 | in7_input 3v output voltage (mV) |
| 68 | in8_input Vee (-12v) output voltage (mV) |
| 69 | |
| 70 | in5_min_alarm 12v output undervoltage alarm |
| 71 | in6_min_alarm 5v output undervoltage alarm |
| 72 | in7_min_alarm 3v output undervoltage alarm |
| 73 | in8_min_alarm Vee (-12v) output undervoltage alarm |
| 74 | |
| 75 | in9_input GPIO voltage data |
| 76 | |
| 77 | power1_input 12v power usage (mW) |
| 78 | power2_input 5v power usage (mW) |
| 79 | power3_input 3v power usage (mW) |
| 80 | power4_input Vee (-12v) power usage (mW) |