[GitHub/mt8127/android_kernel_alcatel_ttab.git] / drivers / atm / Kconfig

#
# ATM device configuration
#

menuconfig ATM_DRIVERS
	bool "ATM drivers"
	depends on NETDEVICES && ATM
	default y

if ATM_DRIVERS

config ATM_DUMMY
	tristate "Dummy ATM driver"
	help
	  Dummy ATM driver. Useful for proxy signalling, testing,
	  and development.  If unsure, say N.

config ATM_TCP
	tristate "ATM over TCP"
	depends on INET
	help
	  ATM over TCP driver. Useful mainly for development and for
	  experiments. If unsure, say N.

config ATM_LANAI
	tristate "Efficient Networks Speedstream 3010"
	depends on PCI && ATM
	help
	  Supports ATM cards based on the Efficient Networks "Lanai"
	  chipset such as the Speedstream 3010 and the ENI-25p.  The
	  Speedstream 3060 is currently not supported since we don't
	  have the code to drive the on-board Alcatel DSL chipset (yet).

config ATM_ENI
	tristate "Efficient Networks ENI155P"
	depends on PCI
	---help---
	  Driver for the Efficient Networks ENI155p series and SMC ATM
	  Power155 155 Mbps ATM adapters. Both, the versions with 512KB and
	  2MB on-board RAM (Efficient calls them "C" and "S", respectively),
	  and the FPGA and the ASIC Tonga versions of the board are supported.
	  The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D)
	  adapters.

	  To compile this driver as a module, choose M here: the module will
	  be called eni.

config ATM_ENI_DEBUG
	bool "Enable extended debugging"
	depends on ATM_ENI
	help
	  Extended debugging records various events and displays that list
	  when an inconsistency is detected. This mechanism is faster than
	  generally using printks, but still has some impact on performance.
	  Note that extended debugging may create certain race conditions
	  itself. Enable this ONLY if you suspect problems with the driver.

config ATM_ENI_TUNE_BURST
	bool "Fine-tune burst settings"
	depends on ATM_ENI
	---help---
	  In order to obtain good throughput, the ENI NIC can transfer
	  multiple words of data per PCI bus access cycle. Such a multi-word
	  transfer is called a burst.

	  The default settings for the burst sizes are suitable for most PCI
	  chipsets. However, in some cases, large bursts may overrun buffers
	  in the PCI chipset and cause data corruption. In such cases, large
	  bursts must be disabled and only (slower) small bursts can be used.
	  The burst sizes can be set independently in the send (TX) and
	  receive (RX) direction.

	  Note that enabling many different burst sizes in the same direction
	  may increase the cost of setting up a transfer such that the
	  resulting throughput is lower than when using only the largest
	  available burst size.

	  Also, sometimes larger bursts lead to lower throughput, e.g. on an
	  Intel 440FX board, a drop from 135 Mbps to 103 Mbps was observed
	  when going from 8W to 16W bursts.

config ATM_ENI_BURST_TX_16W
	bool "Enable 16W TX bursts (discouraged)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst sixteen words at once in the send direction. This may work
	  with recent PCI chipsets, but is known to fail with older chipsets.

config ATM_ENI_BURST_TX_8W
	bool "Enable 8W TX bursts (recommended)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst eight words at once in the send direction. This is the default
	  setting.

config ATM_ENI_BURST_TX_4W
	bool "Enable 4W TX bursts (optional)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst four words at once in the send direction. You may want to try
	  this if you have disabled 8W bursts. Enabling 4W if 8W is also set
	  may or may not improve throughput.

config ATM_ENI_BURST_TX_2W
	bool "Enable 2W TX bursts (optional)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst two words at once in the send direction. You may want to try
	  this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or 8W
	  are also set may or may not improve throughput.

config ATM_ENI_BURST_RX_16W
	bool "Enable 16W RX bursts (discouraged)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst sixteen words at once in the receive direction. This may work
	  with recent PCI chipsets, but is known to fail with older chipsets.

config ATM_ENI_BURST_RX_8W
	bool "Enable 8W RX bursts (discouraged)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst eight words at once in the receive direction. This may work
	  with recent PCI chipsets, but is known to fail with older chipsets,
	  such as the Intel Neptune series.

config ATM_ENI_BURST_RX_4W
	bool "Enable 4W RX bursts (recommended)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst four words at once in the receive direction. This is the
	  default setting. Enabling 4W if 8W is also set may or may not
	  improve throughput.

config ATM_ENI_BURST_RX_2W
	bool "Enable 2W RX bursts (optional)"
	depends on ATM_ENI_TUNE_BURST
	help
	  Burst two words at once in the receive direction. You may want to
	  try this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or
	  8W are also set may or may not improve throughput.

config ATM_FIRESTREAM
	tristate "Fujitsu FireStream (FS50/FS155) "
	depends on PCI
	help
	  Driver for the Fujitsu FireStream 155 (MB86697) and
	  FireStream 50 (MB86695) ATM PCI chips.

	  To compile this driver as a module, choose M here: the module will
	  be called firestream.

config ATM_ZATM
	tristate "ZeitNet ZN1221/ZN1225"
	depends on PCI
	help
	  Driver for the ZeitNet ZN1221 (MMF) and ZN1225 (UTP-5) 155 Mbps ATM
	  adapters.

	  To compile this driver as a module, choose M here: the module will
	  be called zatm.

config ATM_ZATM_DEBUG
	bool "Enable extended debugging"
	depends on ATM_ZATM
	help
	  Extended debugging records various events and displays that list
	  when an inconsistency is detected. This mechanism is faster than
	  generally using printks, but still has some impact on performance.
	  Note that extended debugging may create certain race conditions
	  itself. Enable this ONLY if you suspect problems with the driver.

config ATM_NICSTAR
	tristate "IDT 77201 (NICStAR) (ForeRunnerLE)"
	depends on PCI && !64BIT
	help
	  The NICStAR chipset family is used in a large number of ATM NICs for
	  25 and for 155 Mbps, including IDT cards and the Fore ForeRunnerLE
	  series. Say Y if you have one of those.

	  To compile this driver as a module, choose M here: the module will
	  be called nicstar.

config ATM_NICSTAR_USE_SUNI
	bool "Use suni PHY driver (155Mbps)"
	depends on ATM_NICSTAR
	help
	  Support for the S-UNI and compatible PHYsical layer chips. These are
	  found in most 155Mbps NICStAR based ATM cards, namely in the
	  ForeRunner LE155 cards. This driver provides detection of cable~
	  removal and reinsertion and provides some statistics. This driver
	  doesn't have removal capability when compiled as a module, so if you
	  need that capability don't include S-UNI support (it's not needed to
	  make the card work).

config ATM_NICSTAR_USE_IDT77105
	bool "Use IDT77015 PHY driver (25Mbps)"
	depends on ATM_NICSTAR
	help
	  Support for the PHYsical layer chip in ForeRunner LE25 cards. In
	  addition to cable removal/reinsertion detection, this driver allows
	  you to control the loopback mode of the chip via a dedicated IOCTL.
	  This driver is required for proper handling of temporary carrier
	  loss, so if you have a 25Mbps NICStAR based ATM card you must say Y.

config ATM_IDT77252
	tristate "IDT 77252 (NICStAR II)"
	depends on PCI
	help
	  Driver for the IDT 77252 ATM PCI chips.

	  To compile this driver as a module, choose M here: the module will
	  be called idt77252.

config ATM_IDT77252_DEBUG
	bool "Enable debugging messages"
	depends on ATM_IDT77252
	help
	  Somewhat useful debugging messages are available. The choice of
	  messages is controlled by a bitmap.  This may be specified as a
	  module argument.  See the file <file:drivers/atm/idt77252.h> for
	  the meanings of the bits in the mask.

	  When active, these messages can have a significant impact on the
	  speed of the driver, and the size of your syslog files! When
	  inactive, they will have only a modest impact on performance.

config ATM_IDT77252_RCV_ALL
	bool "Receive ALL cells in raw queue"
	depends on ATM_IDT77252
	help
	  Enable receiving of all cells on the ATM link, that do not match
	  an open connection in the raw cell queue of the driver.  Useful
	  for debugging or special applications only, so the safe answer is N.

config ATM_IDT77252_USE_SUNI
	bool
	depends on ATM_IDT77252
	default y

config ATM_AMBASSADOR
	tristate "Madge Ambassador (Collage PCI 155 Server)"
	depends on PCI
	select BITREVERSE
	help
	  This is a driver for ATMizer based ATM card produced by Madge
	  Networks Ltd. Say Y (or M to compile as a module named ambassador)
	  here if you have one of these cards.

config ATM_AMBASSADOR_DEBUG
	bool "Enable debugging messages"
	depends on ATM_AMBASSADOR
	---help---
	  Somewhat useful debugging messages are available. The choice of
	  messages is controlled by a bitmap.  This may be specified as a
	  module argument (kernel command line argument as well?), changed
	  dynamically using an ioctl (not yet) or changed by sending the
	  string "Dxxxx" to VCI 1023 (where x is a hex digit).  See the file
	  <file:drivers/atm/ambassador.h> for the meanings of the bits in the
	  mask.

	  When active, these messages can have a significant impact on the
	  speed of the driver, and the size of your syslog files! When
	  inactive, they will have only a modest impact on performance.

config ATM_HORIZON
	tristate "Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)"
	depends on PCI
	help
	  This is a driver for the Horizon chipset ATM adapter cards once
	  produced by Madge Networks Ltd. Say Y (or M to compile as a module
	  named horizon) here if you have one of these cards.

config ATM_HORIZON_DEBUG
	bool "Enable debugging messages"
	depends on ATM_HORIZON
	---help---
	  Somewhat useful debugging messages are available. The choice of
	  messages is controlled by a bitmap.  This may be specified as a
	  module argument (kernel command line argument as well?), changed
	  dynamically using an ioctl (not yet) or changed by sending the
	  string "Dxxxx" to VCI 1023 (where x is a hex digit).  See the file
	  <file:drivers/atm/horizon.h> for the meanings of the bits in the
	  mask.

	  When active, these messages can have a significant impact on the
	  speed of the driver, and the size of your syslog files! When
	  inactive, they will have only a modest impact on performance.

config ATM_IA
	tristate "Interphase ATM PCI x575/x525/x531"
	depends on PCI && !64BIT
	---help---
	  This is a driver for the Interphase (i)ChipSAR adapter cards
	  which include a variety of variants in term of the size of the
	  control memory (128K-1KVC, 512K-4KVC), the size of the packet
	  memory (128K, 512K, 1M), and the PHY type (Single/Multi mode OC3,
	  UTP155, UTP25, DS3 and E3). Go to:
	  	<http://www.iphase.com/products/ClassSheet.cfm?ClassID=ATM>
	  for more info about the cards. Say Y (or M to compile as a module
	  named iphase) here if you have one of these cards.

	  See the file <file:Documentation/networking/iphase.txt> for further
	  details.

config ATM_IA_DEBUG
	bool "Enable debugging messages"
	depends on ATM_IA
	---help---
	  Somewhat useful debugging messages are available. The choice of
	  messages is controlled by a bitmap. This may be specified as a
	  module argument (kernel command line argument as well?), changed
	  dynamically using an ioctl (Get the debug utility, iadbg, from
	  <ftp://ftp.iphase.com/pub/atm/pci/>).

	  See the file <file:drivers/atm/iphase.h> for the meanings of the
	  bits in the mask.

	  When active, these messages can have a significant impact on the
	  speed of the driver, and the size of your syslog files! When
	  inactive, they will have only a modest impact on performance.

config ATM_FORE200E_MAYBE
	tristate "FORE Systems 200E-series"
	depends on PCI || SBUS
	---help---
	  This is a driver for the FORE Systems 200E-series ATM adapter
	  cards. It simultaneously supports PCA-200E and SBA-200E models
	  on PCI and SBUS hosts. Say Y (or M to compile as a module
	  named fore_200e) here if you have one of these ATM adapters.

	  Note that the driver will actually be compiled only if you
	  additionally enable the support for PCA-200E and/or SBA-200E
	  cards.

	  See the file <file:Documentation/networking/fore200e.txt> for
	  further details.

config ATM_FORE200E_PCA
	bool "PCA-200E support"
	depends on ATM_FORE200E_MAYBE && PCI
	help
	  Say Y here if you want your PCA-200E cards to be probed.

config ATM_FORE200E_PCA_DEFAULT_FW
	bool "Use default PCA-200E firmware (normally enabled)"
	depends on ATM_FORE200E_PCA
	help
	  Use the default PCA-200E firmware data shipped with the driver.

	  Normal users do not have to deal with the firmware stuff, so
	  they should say Y here.

config ATM_FORE200E_PCA_FW
	string "Pathname of user-supplied binary firmware"
	depends on ATM_FORE200E_PCA && !ATM_FORE200E_PCA_DEFAULT_FW
	default ""
	help
	  This defines the pathname of an alternative PCA-200E binary
	  firmware image supplied by the user. This pathname may be
	  absolute or relative to the drivers/atm directory.

	  The driver comes with an adequate firmware image, so normal users do
	  not have to supply an alternative one. They just say Y to "Use
	  default PCA-200E firmware" instead.

config ATM_FORE200E_SBA
	bool "SBA-200E support"
	depends on ATM_FORE200E_MAYBE && SBUS
	help
	  Say Y here if you want your SBA-200E cards to be probed.

config ATM_FORE200E_SBA_DEFAULT_FW
	bool "Use default SBA-200E firmware (normally enabled)"
	depends on ATM_FORE200E_SBA
	help
	  Use the default SBA-200E firmware data shipped with the driver.

	  Normal users do not have to deal with the firmware stuff, so
	  they should say Y here.

config ATM_FORE200E_SBA_FW
	string "Pathname of user-supplied binary firmware"
	depends on ATM_FORE200E_SBA && !ATM_FORE200E_SBA_DEFAULT_FW
	default ""
	help
	  This defines the pathname of an alternative SBA-200E binary
	  firmware image supplied by the user. This pathname may be
	  absolute or relative to the drivers/atm directory.

	  The driver comes with an adequate firmware image, so normal users do
	  not have to supply an alternative one. They just say Y to "Use
	  default SBA-200E firmware", above.

config ATM_FORE200E_USE_TASKLET
	bool "Defer interrupt work to a tasklet"
	depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA)
	default n
	help
	  This defers work to be done by the interrupt handler to a
	  tasklet instead of handling everything at interrupt time.  This
	  may improve the responsive of the host.

config ATM_FORE200E_TX_RETRY
	int "Maximum number of tx retries"
	depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA)
	default "16"
	---help---
	  Specifies the number of times the driver attempts to transmit
	  a message before giving up, if the transmit queue of the ATM card
	  is transiently saturated.

	  Saturation of the transmit queue may occur only under extreme
	  conditions, e.g. when a fast host continuously submits very small
	  frames (<64 bytes) or raw AAL0 cells (48 bytes) to the ATM adapter.

	  Note that under common conditions, it is unlikely that you encounter
	  a saturation of the transmit queue, so the retry mechanism never
	  comes into play.

config ATM_FORE200E_DEBUG
	int "Debugging level (0-3)"
	depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA)
	default "0"
	help
	  Specifies the level of debugging messages issued by the driver.
	  The verbosity of the driver increases with the value of this
	  parameter.

	  When active, these messages can have a significant impact on
	  the performances of the driver, and the size of your syslog files!
	  Keep the debugging level to 0 during normal operations.

config ATM_FORE200E
	tristate
	depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA)
	default m if ATM_FORE200E_MAYBE!=y
	default y if ATM_FORE200E_MAYBE=y

config ATM_HE
	tristate "ForeRunner HE Series"
	depends on PCI
	help
	  This is a driver for the Marconi ForeRunner HE-series ATM adapter
	  cards. It simultaneously supports the 155 and 622 versions.

config ATM_HE_USE_SUNI
	bool "Use S/UNI PHY driver"
	depends on ATM_HE
	help
	  Support for the S/UNI-Ultra and S/UNI-622 found in the ForeRunner
	  HE cards.  This driver provides carrier detection some statistics.

endif # ATM
Commit	Line	Data
1da177e4 LT	1	#
	2	# ATM device configuration
	3	#
	4
4151ce31 JE	5	menuconfig ATM_DRIVERS
4151ce31 JE	6	bool "ATM drivers"
1da177e4	7	depends on NETDEVICES && ATM
4151ce31 JE	8	default y
	9
	10	if ATM_DRIVERS
1da177e4	11
fb296449 CW	12	config ATM_DUMMY
fb296449 CW	13	tristate "Dummy ATM driver"
fb296449 CW	14	help
	15	Dummy ATM driver. Useful for proxy signalling, testing,
	16	and development. If unsure, say N.
	17
1da177e4 LT	18	config ATM_TCP
1da177e4 LT	19	tristate "ATM over TCP"
4151ce31	20	depends on INET
1da177e4 LT	21	help
	22	ATM over TCP driver. Useful mainly for development and for
	23	experiments. If unsure, say N.
	24
	25	config ATM_LANAI
	26	tristate "Efficient Networks Speedstream 3010"
	27	depends on PCI && ATM
	28	help
	29	Supports ATM cards based on the Efficient Networks "Lanai"
	30	chipset such as the Speedstream 3010 and the ENI-25p. The
	31	Speedstream 3060 is currently not supported since we don't
	32	have the code to drive the on-board Alcatel DSL chipset (yet).
	33
	34	config ATM_ENI
	35	tristate "Efficient Networks ENI155P"
4151ce31	36	depends on PCI
1da177e4 LT	37	---help---
	38	Driver for the Efficient Networks ENI155p series and SMC ATM
	39	Power155 155 Mbps ATM adapters. Both, the versions with 512KB and
	40	2MB on-board RAM (Efficient calls them "C" and "S", respectively),
	41	and the FPGA and the ASIC Tonga versions of the board are supported.
	42	The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D)
	43	adapters.
	44
	45	To compile this driver as a module, choose M here: the module will
	46	be called eni.
	47
	48	config ATM_ENI_DEBUG
	49	bool "Enable extended debugging"
	50	depends on ATM_ENI
	51	help
	52	Extended debugging records various events and displays that list
	53	when an inconsistency is detected. This mechanism is faster than
	54	generally using printks, but still has some impact on performance.
	55	Note that extended debugging may create certain race conditions
	56	itself. Enable this ONLY if you suspect problems with the driver.
	57
	58	config ATM_ENI_TUNE_BURST
	59	bool "Fine-tune burst settings"
	60	depends on ATM_ENI
	61	---help---
	62	In order to obtain good throughput, the ENI NIC can transfer
	63	multiple words of data per PCI bus access cycle. Such a multi-word
	64	transfer is called a burst.
	65
	66	The default settings for the burst sizes are suitable for most PCI
	67	chipsets. However, in some cases, large bursts may overrun buffers
	68	in the PCI chipset and cause data corruption. In such cases, large
	69	bursts must be disabled and only (slower) small bursts can be used.
	70	The burst sizes can be set independently in the send (TX) and
	71	receive (RX) direction.
	72
	73	Note that enabling many different burst sizes in the same direction
	74	may increase the cost of setting up a transfer such that the
	75	resulting throughput is lower than when using only the largest
	76	available burst size.
	77
	78	Also, sometimes larger bursts lead to lower throughput, e.g. on an
	79	Intel 440FX board, a drop from 135 Mbps to 103 Mbps was observed
	80	when going from 8W to 16W bursts.
	81
	82	config ATM_ENI_BURST_TX_16W
	83	bool "Enable 16W TX bursts (discouraged)"
	84	depends on ATM_ENI_TUNE_BURST
	85	help
	86	Burst sixteen words at once in the send direction. This may work
	87	with recent PCI chipsets, but is known to fail with older chipsets.
	88
	89	config ATM_ENI_BURST_TX_8W
	90	bool "Enable 8W TX bursts (recommended)"
	91	depends on ATM_ENI_TUNE_BURST
	92	help
	93	Burst eight words at once in the send direction. This is the default
	94	setting.
	95
	96	config ATM_ENI_BURST_TX_4W
	97	bool "Enable 4W TX bursts (optional)"
	98	depends on ATM_ENI_TUNE_BURST
	99	help
	100	Burst four words at once in the send direction. You may want to try
101	this if you have disabled 8W bursts. Enabling 4W if 8W is also set
102	may or may not improve throughput.
103
104	config ATM_ENI_BURST_TX_2W
105	bool "Enable 2W TX bursts (optional)"
106	depends on ATM_ENI_TUNE_BURST
107	help
108	Burst two words at once in the send direction. You may want to try
109	this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or 8W
110	are also set may or may not improve throughput.
111
112	config ATM_ENI_BURST_RX_16W
113	bool "Enable 16W RX bursts (discouraged)"
114	depends on ATM_ENI_TUNE_BURST
115	help
116	Burst sixteen words at once in the receive direction. This may work
117	with recent PCI chipsets, but is known to fail with older chipsets.
118
119	config ATM_ENI_BURST_RX_8W
120	bool "Enable 8W RX bursts (discouraged)"
121	depends on ATM_ENI_TUNE_BURST
122	help
123	Burst eight words at once in the receive direction. This may work
124	with recent PCI chipsets, but is known to fail with older chipsets,
125	such as the Intel Neptune series.
126
127	config ATM_ENI_BURST_RX_4W
128	bool "Enable 4W RX bursts (recommended)"
129	depends on ATM_ENI_TUNE_BURST
130	help
131	Burst four words at once in the receive direction. This is the
132	default setting. Enabling 4W if 8W is also set may or may not
133	improve throughput.
134
135	config ATM_ENI_BURST_RX_2W
136	bool "Enable 2W RX bursts (optional)"
137	depends on ATM_ENI_TUNE_BURST
138	help
139	Burst two words at once in the receive direction. You may want to
140	try this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or
141	8W are also set may or may not improve throughput.
142
143	config ATM_FIRESTREAM
144	tristate "Fujitsu FireStream (FS50/FS155) "
4151ce31	145	depends on PCI
1da177e4 LT	146	help
	147	Driver for the Fujitsu FireStream 155 (MB86697) and
	148	FireStream 50 (MB86695) ATM PCI chips.
	149
	150	To compile this driver as a module, choose M here: the module will
	151	be called firestream.
	152
	153	config ATM_ZATM
	154	tristate "ZeitNet ZN1221/ZN1225"
4151ce31	155	depends on PCI
1da177e4 LT	156	help
	157	Driver for the ZeitNet ZN1221 (MMF) and ZN1225 (UTP-5) 155 Mbps ATM
	158	adapters.
	159
	160	To compile this driver as a module, choose M here: the module will
	161	be called zatm.
	162
	163	config ATM_ZATM_DEBUG
	164	bool "Enable extended debugging"
	165	depends on ATM_ZATM
	166	help
	167	Extended debugging records various events and displays that list
	168	when an inconsistency is detected. This mechanism is faster than
	169	generally using printks, but still has some impact on performance.
	170	Note that extended debugging may create certain race conditions
	171	itself. Enable this ONLY if you suspect problems with the driver.
	172
1da177e4 LT	173	config ATM_NICSTAR
1da177e4 LT	174	tristate "IDT 77201 (NICStAR) (ForeRunnerLE)"
4151ce31	175	depends on PCI && !64BIT
1da177e4 LT	176	help
	177	The NICStAR chipset family is used in a large number of ATM NICs for
	178	25 and for 155 Mbps, including IDT cards and the Fore ForeRunnerLE
	179	series. Say Y if you have one of those.
	180
	181	To compile this driver as a module, choose M here: the module will
	182	be called nicstar.
	183
	184	config ATM_NICSTAR_USE_SUNI
	185	bool "Use suni PHY driver (155Mbps)"
	186	depends on ATM_NICSTAR
	187	help
	188	Support for the S-UNI and compatible PHYsical layer chips. These are
	189	found in most 155Mbps NICStAR based ATM cards, namely in the
	190	ForeRunner LE155 cards. This driver provides detection of cable~
	191	removal and reinsertion and provides some statistics. This driver
	192	doesn't have removal capability when compiled as a module, so if you
	193	need that capability don't include S-UNI support (it's not needed to
	194	make the card work).
	195
	196	config ATM_NICSTAR_USE_IDT77105
	197	bool "Use IDT77015 PHY driver (25Mbps)"
	198	depends on ATM_NICSTAR
	199	help
	200	Support for the PHYsical layer chip in ForeRunner LE25 cards. In
	201	addition to cable removal/reinsertion detection, this driver allows
	202	you to control the loopback mode of the chip via a dedicated IOCTL.
	203	This driver is required for proper handling of temporary carrier
	204	loss, so if you have a 25Mbps NICStAR based ATM card you must say Y.
	205
	206	config ATM_IDT77252
	207	tristate "IDT 77252 (NICStAR II)"
4151ce31	208	depends on PCI
1da177e4 LT	209	help
	210	Driver for the IDT 77252 ATM PCI chips.
	211
	212	To compile this driver as a module, choose M here: the module will
	213	be called idt77252.
	214
	215	config ATM_IDT77252_DEBUG
	216	bool "Enable debugging messages"
	217	depends on ATM_IDT77252
	218	help
	219	Somewhat useful debugging messages are available. The choice of
	220	messages is controlled by a bitmap. This may be specified as a
	221	module argument. See the file <file:drivers/atm/idt77252.h> for
	222	the meanings of the bits in the mask.
	223
	224	When active, these messages can have a significant impact on the
	225	speed of the driver, and the size of your syslog files! When
	226	inactive, they will have only a modest impact on performance.
	227
	228	config ATM_IDT77252_RCV_ALL
	229	bool "Receive ALL cells in raw queue"
	230	depends on ATM_IDT77252
	231	help
	232	Enable receiving of all cells on the ATM link, that do not match
	233	an open connection in the raw cell queue of the driver. Useful
	234	for debugging or special applications only, so the safe answer is N.
	235
	236	config ATM_IDT77252_USE_SUNI
	237	bool
	238	depends on ATM_IDT77252
	239	default y
	240
	241	config ATM_AMBASSADOR
	242	tristate "Madge Ambassador (Collage PCI 155 Server)"
4151ce31	243	depends on PCI
0a858857	244	select BITREVERSE
1da177e4 LT	245	help
	246	This is a driver for ATMizer based ATM card produced by Madge
	247	Networks Ltd. Say Y (or M to compile as a module named ambassador)
	248	here if you have one of these cards.
	249
	250	config ATM_AMBASSADOR_DEBUG
	251	bool "Enable debugging messages"
	252	depends on ATM_AMBASSADOR
	253	---help---
	254	Somewhat useful debugging messages are available. The choice of
	255	messages is controlled by a bitmap. This may be specified as a
	256	module argument (kernel command line argument as well?), changed
	257	dynamically using an ioctl (not yet) or changed by sending the
	258	string "Dxxxx" to VCI 1023 (where x is a hex digit). See the file
	259	<file:drivers/atm/ambassador.h> for the meanings of the bits in the
	260	mask.
	261
	262	When active, these messages can have a significant impact on the
	263	speed of the driver, and the size of your syslog files! When
	264	inactive, they will have only a modest impact on performance.
	265
	266	config ATM_HORIZON
	267	tristate "Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)"
4151ce31	268	depends on PCI
1da177e4 LT	269	help
	270	This is a driver for the Horizon chipset ATM adapter cards once
	271	produced by Madge Networks Ltd. Say Y (or M to compile as a module
	272	named horizon) here if you have one of these cards.
	273
	274	config ATM_HORIZON_DEBUG
	275	bool "Enable debugging messages"
	276	depends on ATM_HORIZON
	277	---help---
	278	Somewhat useful debugging messages are available. The choice of
	279	messages is controlled by a bitmap. This may be specified as a
	280	module argument (kernel command line argument as well?), changed
	281	dynamically using an ioctl (not yet) or changed by sending the
	282	string "Dxxxx" to VCI 1023 (where x is a hex digit). See the file
	283	<file:drivers/atm/horizon.h> for the meanings of the bits in the
	284	mask.
	285
	286	When active, these messages can have a significant impact on the
	287	speed of the driver, and the size of your syslog files! When
	288	inactive, they will have only a modest impact on performance.
	289
	290	config ATM_IA
	291	tristate "Interphase ATM PCI x575/x525/x531"
4151ce31	292	depends on PCI && !64BIT
1da177e4 LT	293	---help---
	294	This is a driver for the Interphase (i)ChipSAR adapter cards
	295	which include a variety of variants in term of the size of the
	296	control memory (128K-1KVC, 512K-4KVC), the size of the packet
	297	memory (128K, 512K, 1M), and the PHY type (Single/Multi mode OC3,
	298	UTP155, UTP25, DS3 and E3). Go to:
	299	<http://www.iphase.com/products/ClassSheet.cfm?ClassID=ATM>
	300	for more info about the cards. Say Y (or M to compile as a module
	301	named iphase) here if you have one of these cards.
	302
	303	See the file <file:Documentation/networking/iphase.txt> for further
	304	details.
	305
	306	config ATM_IA_DEBUG
	307	bool "Enable debugging messages"
	308	depends on ATM_IA
	309	---help---
	310	Somewhat useful debugging messages are available. The choice of
	311	messages is controlled by a bitmap. This may be specified as a
	312	module argument (kernel command line argument as well?), changed
	313	dynamically using an ioctl (Get the debug utility, iadbg, from
	314	<ftp://ftp.iphase.com/pub/atm/pci/>).
	315
	316	See the file <file:drivers/atm/iphase.h> for the meanings of the
	317	bits in the mask.
	318
	319	When active, these messages can have a significant impact on the
	320	speed of the driver, and the size of your syslog files! When
	321	inactive, they will have only a modest impact on performance.
	322
	323	config ATM_FORE200E_MAYBE
	324	tristate "FORE Systems 200E-series"
4151ce31	325	depends on PCI \|\| SBUS
1da177e4 LT	326	---help---
	327	This is a driver for the FORE Systems 200E-series ATM adapter
	328	cards. It simultaneously supports PCA-200E and SBA-200E models
	329	on PCI and SBUS hosts. Say Y (or M to compile as a module
	330	named fore_200e) here if you have one of these ATM adapters.
	331
	332	Note that the driver will actually be compiled only if you
	333	additionally enable the support for PCA-200E and/or SBA-200E
	334	cards.
	335
	336	See the file <file:Documentation/networking/fore200e.txt> for
	337	further details.
	338
	339	config ATM_FORE200E_PCA
	340	bool "PCA-200E support"
	341	depends on ATM_FORE200E_MAYBE && PCI
	342	help
	343	Say Y here if you want your PCA-200E cards to be probed.
	344
	345	config ATM_FORE200E_PCA_DEFAULT_FW
	346	bool "Use default PCA-200E firmware (normally enabled)"
	347	depends on ATM_FORE200E_PCA
	348	help
	349	Use the default PCA-200E firmware data shipped with the driver.
	350
	351	Normal users do not have to deal with the firmware stuff, so
	352	they should say Y here.
	353
	354	config ATM_FORE200E_PCA_FW
	355	string "Pathname of user-supplied binary firmware"
	356	depends on ATM_FORE200E_PCA && !ATM_FORE200E_PCA_DEFAULT_FW
	357	default ""
	358	help
	359	This defines the pathname of an alternative PCA-200E binary
	360	firmware image supplied by the user. This pathname may be
	361	absolute or relative to the drivers/atm directory.
	362
	363	The driver comes with an adequate firmware image, so normal users do
	364	not have to supply an alternative one. They just say Y to "Use
	365	default PCA-200E firmware" instead.
	366
	367	config ATM_FORE200E_SBA
	368	bool "SBA-200E support"
	369	depends on ATM_FORE200E_MAYBE && SBUS
	370	help
	371	Say Y here if you want your SBA-200E cards to be probed.
	372
	373	config ATM_FORE200E_SBA_DEFAULT_FW
	374	bool "Use default SBA-200E firmware (normally enabled)"
	375	depends on ATM_FORE200E_SBA
	376	help
	377	Use the default SBA-200E firmware data shipped with the driver.
	378
	379	Normal users do not have to deal with the firmware stuff, so
	380	they should say Y here.
	381
	382	config ATM_FORE200E_SBA_FW
	383	string "Pathname of user-supplied binary firmware"
	384	depends on ATM_FORE200E_SBA && !ATM_FORE200E_SBA_DEFAULT_FW
	385	default ""
	386	help
	387	This defines the pathname of an alternative SBA-200E binary
	388	firmware image supplied by the user. This pathname may be
	389	absolute or relative to the drivers/atm directory.
390
391	The driver comes with an adequate firmware image, so normal users do
392	not have to supply an alternative one. They just say Y to "Use
393	default SBA-200E firmware", above.
394
395	config ATM_FORE200E_USE_TASKLET
396	bool "Defer interrupt work to a tasklet"
397	depends on (PCI \|\| SBUS) && (ATM_FORE200E_PCA \|\| ATM_FORE200E_SBA)
398	default n
399	help
400	This defers work to be done by the interrupt handler to a
00181fc9	401	tasklet instead of handling everything at interrupt time. This
1da177e4 LT	402	may improve the responsive of the host.
	403
	404	config ATM_FORE200E_TX_RETRY
	405	int "Maximum number of tx retries"
	406	depends on (PCI \|\| SBUS) && (ATM_FORE200E_PCA \|\| ATM_FORE200E_SBA)
	407	default "16"
	408	---help---
	409	Specifies the number of times the driver attempts to transmit
	410	a message before giving up, if the transmit queue of the ATM card
	411	is transiently saturated.
	412
	413	Saturation of the transmit queue may occur only under extreme
	414	conditions, e.g. when a fast host continuously submits very small
	415	frames (<64 bytes) or raw AAL0 cells (48 bytes) to the ATM adapter.
	416
	417	Note that under common conditions, it is unlikely that you encounter
	418	a saturation of the transmit queue, so the retry mechanism never
	419	comes into play.
	420
	421	config ATM_FORE200E_DEBUG
	422	int "Debugging level (0-3)"
	423	depends on (PCI \|\| SBUS) && (ATM_FORE200E_PCA \|\| ATM_FORE200E_SBA)
	424	default "0"
	425	help
	426	Specifies the level of debugging messages issued by the driver.
	427	The verbosity of the driver increases with the value of this
	428	parameter.
	429
	430	When active, these messages can have a significant impact on
	431	the performances of the driver, and the size of your syslog files!
	432	Keep the debugging level to 0 during normal operations.
	433
	434	config ATM_FORE200E
	435	tristate
	436	depends on (PCI \|\| SBUS) && (ATM_FORE200E_PCA \|\| ATM_FORE200E_SBA)
	437	default m if ATM_FORE200E_MAYBE!=y
	438	default y if ATM_FORE200E_MAYBE=y
	439
	440	config ATM_HE
	441	tristate "ForeRunner HE Series"
4151ce31	442	depends on PCI
1da177e4 LT	443	help
	444	This is a driver for the Marconi ForeRunner HE-series ATM adapter
	445	cards. It simultaneously supports the 155 and 622 versions.
	446
	447	config ATM_HE_USE_SUNI
	448	bool "Use S/UNI PHY driver"
	449	depends on ATM_HE
	450	help
	451	Support for the S/UNI-Ultra and S/UNI-622 found in the ForeRunner
	452	HE cards. This driver provides carrier detection some statistics.
	453
4151ce31	454	endif # ATM