Commit | Line | Data |
---|---|---|
61352667 | 1 | /* |
2 | * Copyright (C) 2005 SAN People | |
3 | * Copyright (C) 2008 Atmel | |
4 | * | |
5 | * This program is free software; you can redistribute it and/or modify | |
6 | * it under the terms of the GNU General Public License as published by | |
7 | * the Free Software Foundation; either version 2 of the License, or | |
8 | * (at your option) any later version. | |
9 | * | |
10 | * This program is distributed in the hope that it will be useful, | |
11 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
12 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
13 | * GNU General Public License for more details. | |
14 | * | |
15 | * You should have received a copy of the GNU General Public License | |
16 | * along with this program; if not, write to the Free Software | |
17 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
18 | */ | |
19 | ||
20 | #include <linux/types.h> | |
21 | #include <linux/init.h> | |
22 | #include <linux/mm.h> | |
23 | #include <linux/module.h> | |
24 | #include <linux/platform_device.h> | |
25 | #include <linux/spi/spi.h> | |
26 | #include <linux/spi/at73c213.h> | |
59c5fe6d NF |
27 | #include <linux/gpio_keys.h> |
28 | #include <linux/input.h> | |
61352667 | 29 | #include <linux/clk.h> |
5e886f68 DES |
30 | #include <linux/regulator/machine.h> |
31 | #include <linux/regulator/fixed.h> | |
32 | #include <linux/regulator/consumer.h> | |
61352667 | 33 | |
a09e64fb | 34 | #include <mach/hardware.h> |
61352667 | 35 | #include <asm/setup.h> |
36 | #include <asm/mach-types.h> | |
37 | #include <asm/irq.h> | |
38 | ||
39 | #include <asm/mach/arch.h> | |
40 | #include <asm/mach/map.h> | |
41 | #include <asm/mach/irq.h> | |
42 | ||
a09e64fb RK |
43 | #include <mach/board.h> |
44 | #include <mach/gpio.h> | |
8cdae51a | 45 | #include <mach/at91sam9_smc.h> |
61352667 | 46 | |
8cdae51a | 47 | #include "sam9_smc.h" |
61352667 | 48 | #include "generic.h" |
49 | ||
a6e016f1 JCPV |
50 | /* |
51 | * board revision encoding | |
52 | * bit 0: | |
53 | * 0 => 1 sd/mmc slot | |
54 | * 1 => 2 sd/mmc slots connectors (board from revision C) | |
55 | */ | |
56 | #define HAVE_2MMC (1 << 0) | |
57 | static int inline ek_have_2mmc(void) | |
58 | { | |
59 | return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC); | |
60 | } | |
61 | ||
61352667 | 62 | |
63 | static void __init ek_map_io(void) | |
64 | { | |
65 | /* Initialize processor: 18.432 MHz crystal */ | |
66 | at91sam9260_initialize(18432000); | |
67 | ||
4f37940d | 68 | /* DBGU on ttyS0. (Rx & Tx only) */ |
61352667 | 69 | at91_register_uart(0, 0, 0); |
70 | ||
71 | /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ | |
72 | at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS | |
73 | | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD | |
74 | | ATMEL_UART_RI); | |
75 | ||
76 | /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */ | |
77 | at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); | |
78 | ||
79 | /* set serial console to ttyS0 (ie, DBGU) */ | |
80 | at91_set_serial_console(0); | |
81 | } | |
82 | ||
83 | static void __init ek_init_irq(void) | |
84 | { | |
85 | at91sam9260_init_interrupts(NULL); | |
86 | } | |
87 | ||
88 | ||
89 | /* | |
90 | * USB Host port | |
91 | */ | |
92 | static struct at91_usbh_data __initdata ek_usbh_data = { | |
93 | .ports = 2, | |
94 | }; | |
95 | ||
96 | /* | |
97 | * USB Device port | |
98 | */ | |
99 | static struct at91_udc_data __initdata ek_udc_data = { | |
100 | .vbus_pin = AT91_PIN_PC5, | |
101 | .pullup_pin = 0, /* pull-up driven by UDC */ | |
102 | }; | |
103 | ||
104 | ||
105 | /* | |
106 | * SPI devices. | |
107 | */ | |
108 | static struct spi_board_info ek_spi_devices[] = { | |
a6e016f1 | 109 | #if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91)) |
61352667 | 110 | { /* DataFlash chip */ |
111 | .modalias = "mtd_dataflash", | |
112 | .chip_select = 1, | |
113 | .max_speed_hz = 15 * 1000 * 1000, | |
114 | .bus_num = 0, | |
115 | }, | |
116 | #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD) | |
117 | { /* DataFlash card */ | |
118 | .modalias = "mtd_dataflash", | |
119 | .chip_select = 0, | |
120 | .max_speed_hz = 15 * 1000 * 1000, | |
121 | .bus_num = 0, | |
122 | }, | |
123 | #endif | |
124 | #endif | |
125 | }; | |
126 | ||
127 | ||
128 | /* | |
129 | * MACB Ethernet device | |
130 | */ | |
131 | static struct at91_eth_data __initdata ek_macb_data = { | |
132 | .phy_irq_pin = AT91_PIN_PA7, | |
133 | .is_rmii = 1, | |
134 | }; | |
135 | ||
a6e016f1 JCPV |
136 | static void __init ek_add_device_macb(void) |
137 | { | |
138 | if (ek_have_2mmc()) | |
139 | ek_macb_data.phy_irq_pin = AT91_PIN_PB0; | |
140 | ||
141 | at91_add_device_eth(&ek_macb_data); | |
142 | } | |
61352667 | 143 | |
144 | /* | |
145 | * NAND flash | |
146 | */ | |
147 | static struct mtd_partition __initdata ek_nand_partition[] = { | |
148 | { | |
149 | .name = "Bootstrap", | |
150 | .offset = 0, | |
e505240b | 151 | .size = 4 * SZ_1M, |
61352667 | 152 | }, |
153 | { | |
154 | .name = "Partition 1", | |
e505240b AV |
155 | .offset = MTDPART_OFS_NXTBLK, |
156 | .size = 60 * SZ_1M, | |
61352667 | 157 | }, |
158 | { | |
159 | .name = "Partition 2", | |
e505240b | 160 | .offset = MTDPART_OFS_NXTBLK, |
61352667 | 161 | .size = MTDPART_SIZ_FULL, |
162 | }, | |
163 | }; | |
164 | ||
165 | static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) | |
166 | { | |
167 | *num_partitions = ARRAY_SIZE(ek_nand_partition); | |
168 | return ek_nand_partition; | |
169 | } | |
170 | ||
171 | /* det_pin is not connected */ | |
7c896834 | 172 | static struct atmel_nand_data __initdata ek_nand_data = { |
61352667 | 173 | .ale = 21, |
174 | .cle = 22, | |
175 | .rdy_pin = AT91_PIN_PC13, | |
176 | .enable_pin = AT91_PIN_PC14, | |
177 | .partition_info = nand_partitions, | |
f6ed6f78 | 178 | #if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16) |
61352667 | 179 | .bus_width_16 = 1, |
180 | #else | |
181 | .bus_width_16 = 0, | |
182 | #endif | |
183 | }; | |
184 | ||
8cdae51a AV |
185 | static struct sam9_smc_config __initdata ek_nand_smc_config = { |
186 | .ncs_read_setup = 0, | |
187 | .nrd_setup = 2, | |
188 | .ncs_write_setup = 0, | |
189 | .nwe_setup = 2, | |
190 | ||
191 | .ncs_read_pulse = 4, | |
192 | .nrd_pulse = 4, | |
193 | .ncs_write_pulse = 4, | |
194 | .nwe_pulse = 4, | |
195 | ||
196 | .read_cycle = 7, | |
197 | .write_cycle = 7, | |
198 | ||
199 | .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, | |
200 | .tdf_cycles = 3, | |
201 | }; | |
202 | ||
203 | static void __init ek_add_device_nand(void) | |
204 | { | |
205 | /* setup bus-width (8 or 16) */ | |
206 | if (ek_nand_data.bus_width_16) | |
207 | ek_nand_smc_config.mode |= AT91_SMC_DBW_16; | |
208 | else | |
209 | ek_nand_smc_config.mode |= AT91_SMC_DBW_8; | |
210 | ||
211 | /* configure chip-select 3 (NAND) */ | |
212 | sam9_smc_configure(3, &ek_nand_smc_config); | |
213 | ||
214 | at91_add_device_nand(&ek_nand_data); | |
215 | } | |
216 | ||
61352667 | 217 | |
218 | /* | |
219 | * MCI (SD/MMC) | |
a6e016f1 | 220 | * wp_pin and vcc_pin are not connected |
61352667 | 221 | */ |
a6e016f1 JCPV |
222 | #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) |
223 | static struct mci_platform_data __initdata ek_mmc_data = { | |
224 | .slot[1] = { | |
225 | .bus_width = 4, | |
226 | .detect_pin = AT91_PIN_PC9, | |
227 | }, | |
228 | ||
229 | }; | |
230 | #else | |
61352667 | 231 | static struct at91_mmc_data __initdata ek_mmc_data = { |
a6e016f1 | 232 | .slot_b = 1, /* Only one slot so use slot B */ |
61352667 | 233 | .wire4 = 1, |
a6e016f1 | 234 | .det_pin = AT91_PIN_PC9, |
61352667 | 235 | }; |
a6e016f1 | 236 | #endif |
61352667 | 237 | |
a6e016f1 JCPV |
238 | static void __init ek_add_device_mmc(void) |
239 | { | |
240 | #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE) | |
241 | if (ek_have_2mmc()) { | |
242 | ek_mmc_data.slot[0].bus_width = 4; | |
243 | ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; | |
244 | } | |
245 | at91_add_device_mci(0, &ek_mmc_data); | |
246 | #else | |
247 | at91_add_device_mmc(0, &ek_mmc_data); | |
248 | #endif | |
249 | } | |
61352667 | 250 | |
251 | /* | |
252 | * LEDs | |
253 | */ | |
254 | static struct gpio_led ek_leds[] = { | |
255 | { /* "bottom" led, green, userled1 to be defined */ | |
256 | .name = "ds5", | |
257 | .gpio = AT91_PIN_PA6, | |
258 | .active_low = 1, | |
259 | .default_trigger = "none", | |
260 | }, | |
261 | { /* "power" led, yellow */ | |
262 | .name = "ds1", | |
263 | .gpio = AT91_PIN_PA9, | |
264 | .default_trigger = "heartbeat", | |
265 | } | |
266 | }; | |
267 | ||
a6e016f1 JCPV |
268 | static void __init ek_add_device_gpio_leds(void) |
269 | { | |
270 | if (ek_have_2mmc()) { | |
271 | ek_leds[0].gpio = AT91_PIN_PB8; | |
272 | ek_leds[1].gpio = AT91_PIN_PB9; | |
273 | } | |
274 | ||
275 | at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); | |
276 | } | |
59c5fe6d NF |
277 | |
278 | /* | |
279 | * GPIO Buttons | |
280 | */ | |
281 | #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) | |
282 | static struct gpio_keys_button ek_buttons[] = { | |
283 | { | |
284 | .gpio = AT91_PIN_PA30, | |
285 | .code = BTN_3, | |
286 | .desc = "Button 3", | |
287 | .active_low = 1, | |
288 | .wakeup = 1, | |
289 | }, | |
290 | { | |
291 | .gpio = AT91_PIN_PA31, | |
292 | .code = BTN_4, | |
293 | .desc = "Button 4", | |
294 | .active_low = 1, | |
295 | .wakeup = 1, | |
296 | } | |
297 | }; | |
298 | ||
299 | static struct gpio_keys_platform_data ek_button_data = { | |
300 | .buttons = ek_buttons, | |
301 | .nbuttons = ARRAY_SIZE(ek_buttons), | |
302 | }; | |
303 | ||
304 | static struct platform_device ek_button_device = { | |
305 | .name = "gpio-keys", | |
306 | .id = -1, | |
307 | .num_resources = 0, | |
308 | .dev = { | |
309 | .platform_data = &ek_button_data, | |
310 | } | |
311 | }; | |
312 | ||
313 | static void __init ek_add_device_buttons(void) | |
314 | { | |
315 | at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */ | |
316 | at91_set_deglitch(AT91_PIN_PA30, 1); | |
317 | at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */ | |
318 | at91_set_deglitch(AT91_PIN_PA31, 1); | |
319 | ||
320 | platform_device_register(&ek_button_device); | |
321 | } | |
322 | #else | |
323 | static void __init ek_add_device_buttons(void) {} | |
324 | #endif | |
325 | ||
5e886f68 DES |
326 | #if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE) |
327 | static struct regulator_consumer_supply ek_audio_consumer_supplies[] = { | |
328 | REGULATOR_SUPPLY("AVDD", "0-001b"), | |
329 | REGULATOR_SUPPLY("HPVDD", "0-001b"), | |
330 | REGULATOR_SUPPLY("DBVDD", "0-001b"), | |
331 | REGULATOR_SUPPLY("DCVDD", "0-001b"), | |
332 | }; | |
333 | ||
334 | static struct regulator_init_data ek_avdd_reg_init_data = { | |
335 | .constraints = { | |
336 | .name = "3V3", | |
337 | .valid_ops_mask = REGULATOR_CHANGE_STATUS, | |
338 | }, | |
339 | .consumer_supplies = ek_audio_consumer_supplies, | |
340 | .num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies), | |
341 | }; | |
342 | ||
343 | static struct fixed_voltage_config ek_vdd_pdata = { | |
344 | .supply_name = "board-3V3", | |
345 | .microvolts = 3300000, | |
346 | .gpio = -EINVAL, | |
347 | .enabled_at_boot = 0, | |
348 | .init_data = &ek_avdd_reg_init_data, | |
349 | }; | |
350 | static struct platform_device ek_voltage_regulator = { | |
351 | .name = "reg-fixed-voltage", | |
352 | .id = -1, | |
353 | .num_resources = 0, | |
354 | .dev = { | |
355 | .platform_data = &ek_vdd_pdata, | |
356 | }, | |
357 | }; | |
358 | static void __init ek_add_regulators(void) | |
359 | { | |
360 | platform_device_register(&ek_voltage_regulator); | |
361 | } | |
362 | #else | |
363 | static void __init ek_add_regulators(void) {} | |
364 | #endif | |
365 | ||
59c5fe6d | 366 | |
6953e47e | 367 | static struct i2c_board_info __initdata ek_i2c_devices[] = { |
438ff39d RA |
368 | { |
369 | I2C_BOARD_INFO("24c512", 0x50) | |
370 | }, | |
371 | { | |
372 | I2C_BOARD_INFO("wm8731", 0x1b) | |
373 | }, | |
6953e47e DES |
374 | }; |
375 | ||
376 | ||
61352667 | 377 | static void __init ek_board_init(void) |
378 | { | |
379 | /* Serial */ | |
380 | at91_add_device_serial(); | |
381 | /* USB Host */ | |
382 | at91_add_device_usbh(&ek_usbh_data); | |
383 | /* USB Device */ | |
384 | at91_add_device_udc(&ek_udc_data); | |
385 | /* SPI */ | |
386 | at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); | |
387 | /* NAND */ | |
8cdae51a | 388 | ek_add_device_nand(); |
61352667 | 389 | /* Ethernet */ |
a6e016f1 | 390 | ek_add_device_macb(); |
5e886f68 DES |
391 | /* Regulators */ |
392 | ek_add_regulators(); | |
61352667 | 393 | /* MMC */ |
a6e016f1 | 394 | ek_add_device_mmc(); |
61352667 | 395 | /* I2C */ |
6953e47e | 396 | at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices)); |
61352667 | 397 | /* LEDs */ |
a6e016f1 | 398 | ek_add_device_gpio_leds(); |
59c5fe6d NF |
399 | /* Push Buttons */ |
400 | ek_add_device_buttons(); | |
423145a5 MB |
401 | /* PCK0 provides MCLK to the WM8731 */ |
402 | at91_set_B_periph(AT91_PIN_PC1, 0); | |
403 | /* SSC (for WM8731) */ | |
404 | at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); | |
61352667 | 405 | } |
406 | ||
407 | MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK") | |
408 | /* Maintainer: Atmel */ | |
61352667 | 409 | .boot_params = AT91_SDRAM_BASE + 0x100, |
410 | .timer = &at91sam926x_timer, | |
411 | .map_io = ek_map_io, | |
412 | .init_irq = ek_init_irq, | |
413 | .init_machine = ek_board_init, | |
414 | MACHINE_END | |
a6e016f1 JCPV |
415 | |
416 | MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod") | |
417 | /* Maintainer: Atmel */ | |
a6e016f1 JCPV |
418 | .boot_params = AT91_SDRAM_BASE + 0x100, |
419 | .timer = &at91sam926x_timer, | |
420 | .map_io = ek_map_io, | |
421 | .init_irq = ek_init_irq, | |
422 | .init_machine = ek_board_init, | |
423 | MACHINE_END |